Advertisement
Scanner Features
Cord Attachment/Removal
Programming Bar Codes
Set Defaults
Set Defaults
Carriage Return/Line Feed
DATA><SUFFIX1>
USB Host Types
HID Keyboard Emulation
IBM Hand-Held USB
SNAPI with Imaging Interface
SNAPI Without Imaging
IBM 46XX Host Types
Port 5B
Port 9B
Port 17
RS-232 Host Types
Standard RS-232
Nixdorf RS-232 Mode A
Nixdorf RS-232 Mode B
ICL RS-232
Fujitsu RS-232
OPOS/JPOS
RFID Same Tag Timeout
Disable
2 Seconds
5 Minutes
RFID Trigger Modes
Continuous
Single Tag
Continuous Re-report
Continuous Flush
RFID Data Transmission Format
Raw
GS1-128
EPC URI
Data Capture
Hands-Free Scanning
Hand-Held Scanning
Triggers
Hands-Free RFID
Hand-Held RFID
LED Indications
| Indication | LED |
| Hand-Held Scanning / RFID | |
| The scanner is on and ready to scan/read, or no power to the scanner | Off |
| The scanner successfully decoded a bar code or read an RFID tag | Green |
| Transmission error | Red |
| Hands-Free (Presentation) Scanning | |
| No power to the scanner | Off |
| The scanner is ready to scan | Green |
| A bar code is successfully decoded | Off momentarily |
| Transmission error | Red |
Beeper Indications
| Indication | Beeper Sequence |
| Standard Use | |
| Power up | Low/medium/high beep |
| A bar code is successfully decoded | Short medium beep |
| Transmission error, data is ignored | 4 long low beeps |
| RFID | |
| An RFID tag was read (if RFID read beeper is enabled) | Medium/high (two-tone) beep |
| Unexpected RFID indication | High/medium/low/low beeps |
| Parameter Menu Scanning | |
| Successful parameter setting | High/low/high/low beep |
| Correct programming sequence performed | High/low beep |
| Incorrect programming sequence, or Cancel bar code scanned | Low/high beep |
Optimum Arm Position
Avoid Extreme Wrist Angles
Avoid Bending and Reaching
Alternate left and right hands. Taking breaks and task rotation recommended.
Troubleshooting
| Problem | Possible Solution |
| Scanner not working | |
| No power to scanner | Check system power; ensure power supply, if required, is connected |
| Incorrect interface cable used | Use correct interface cable |
| Interface/power cables are loose | Ensure all cable connections are secure |
| Scanner does not decode bar code | |
| Scanner not programmed for bar code type | Ensure the scanner is programmed to read the type of bar code being scanned |
| Bar code is unreadable | Ensure the bar code is not defaced; scan a test bar code of the same bar code type |
| Distance between scanner and bar code is incorrect | Move the scanner closer to or further from the bar code |
| Scanner decodes bar code but does not transmit data to host | |
| Scanner not programmed for correct host interface | Scan appropriate host parameter bar codes |
| Interface cable is loose | Ensure all cable connections are secure |
| Scanned data incorrectly displayed on host | |
| Scanner not programmed for correct host interface | Scan appropriate host parameter bar codes |
Ergonomic Recommendations
In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury.
- Reduce or eliminate repetitive motion
- Maintain a natural position
- Reduce or eliminate excessive force
- Keep objects that are used frequently within easy reach
- Perform tasks at correct heights
- Reduce or eliminate vibration
- Reduce or eliminate direct pressure
- Provide adjustable workstations
- Provide adequate clearance
- Provide a suitable working environment
- Improve work procedures.
Service Information
If you have a problem using the equipment, contact your facility's Technical or Systems Support. If there is a problem with the equipment, they will contact the Global Customer Support Center at: http://www.zebra.com/support.
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the DS9808-R and is the answer not in the manual?
Questions and answers