Kenwood TS-870S Instruction Manual page 32
Intelligent digital enhanced communications system
Hide thumbs
Also See for TS-870S:
- Instruction manual (105 pages) ,
- In-depth manual (28 pages) ,
- Operation manual (8 pages)
Table of Contents
Advertisement
Menu
5 MENU SETUP
: Z Menu item :
: Function
28
VOX.GAIN
| VOX gain
0~7
4
*
0 (minimum gain) > 7 (maximum gain)
29
TX.WIDTH
| TX bandwidth for SSB and AM modes
1800/ 2000/ 2300/]
29300 Hz | 47
2600/ 3000 Hz
TX.SHIFT
| 1X bandshift
for SSB and AM modes
O/ 100/ 200/ 300/ | 300Hz | 47
400/ 500 Hz
TX EQ.
TX equalizer for SSB made
H/C/B
H
47
+
H:
High boost
*
C: Comb fiiter
+
B: Bass boost
AUTO.RET | Transceiver Status after tuning with the antenna tuner
OFF/ON
ON
+
OFF:
Transmit status maintained
=
*
ON:
Receive status restored
Note:
if OFF is selected, the transmit status can be aborted by
pressing [AT TUNE}.
OFF may be selected if using a linear amplifier.
|
TUN.WIDE
Allowable SWR range for Antenna Tuner
OFF/ON
OFF
49
*
Tuning stops if:
OFF:
SWR € 1.2:1 (approx.)
ON:
SWR < 1.6:1 (approx.}
AUT.MODE | Automatic Made
OFF/ON
OFF
| 48
BEEP
Button confirmation/ Alarm tone enable
OFF/ON
ON
64
+
OFF:
No Confirmation or Alarm tones
+
ON:
Confirmation and Alarm tones audible
BP. MODE
| Morse code enable for the operating mode
OFF/ON
ON
65
«
OFF:
Single beep
«+
ON:
Morse code
WARN. BP | Error message enable for alarm notification
OFF/ON
ON
65
+
OFF:
Triple beep
+
ON:
Morse error message
BP LV
Beep output level
0~9
4
64
+
0 (minimum level} > 9 (maximum level}
REPEAT
Playback repeat
OFFION
OFF
67
REP.TIME _ | Interval between repeated playbacks
H/ 2/ 3/ 4/5/ 10/15)
Ssec
| 68
20/ 25/ 30/ 35/ 40/
45/ 50/ 55/ 60 sec
F.STEP
Frequency change for one revolution of the
5/10 kHz
40 kHz | 21
Tuning control in SSB, CW, FSK (FINE : OFF)
BC.STEP
|9kHz step enable for the M.CH/VFO.CH control in the
OFF/ON
See page|
21
AM Broadcast band for AM mode
reference
+
OFF:
10 kHz steps
+
ON:
9 kHz steps
43
CH. STEP
| Frequency step size outside the AM broadcast band for
4/5/10 kHz
10kHz | 21
L
the M.CH/VFO.CH control
44
STEPADJ | Alters the function of the M.CH/VFO.CH control if you
24
are operating in VFO mode.
DEBION
ON
+
OFF:
M.CH/VFO.CH steps the VFO frequency from
the current frequency without rounding.
+
ON:
M.CH/VFO.CH steps the VFO frequency but
first rounds off the current frequency.
45
PF.KEY.UL
| Programmable Function button (upper left)
OFF, 00 ~ 73
69
63
(ENTER)
46 | PFKEY.UR
| Programmable Function button (upper right)
OFF, 00 ~ 73
70
63
(TF-SET)
47
PEKEY.LR
| Programmable Function button (lower right)
OFF, 00~73
= |71 (1MHz)
26
Advertisement
Table of Contents
