Be Cool travel carrier + Instruction Manual page 14

EN
3_ INSTALL POSITION OF THE CHILD
SEAT IN VEHICLE
3.1_ Only suitable if the approved vehicles are fitted
with adult 3-point belt, approved to UN/ECE
Regulation No.16 or other equivalent standards.
Always check that the shoulder straps are at the
correct height for your child. The child's shoulder
straps should always be threaded through the slots
in the cover and seat shell that are closest to the top
of your child's shoulders.
3.2_ CHECKING THE SHOULDER STRAP HEIGHT.
Not to use rearward-facing in seating positions
where an active frontal airbag is installed.
Only use on this seat if ISOFIX anchorages are fitted.
3.3_ USAGE OF BUCKLE.
1: Get the left and the right pieces of buckle together.
2: Insert the two pieces into the slot of the buckle.
At the same time, hearing "click" means the buckle
gets stuck, pull the pieces of the buckle and check
whether the buckle is locked correctly.
3: If you want to release the safety belts, it needs to
press the red button,then the pieces pop up.
26
3.4 ADJUST THE LENGTH OF THE Y-SHAPED BELTS
1: Loosen the Y-shaped belts
The Y-shaped belts can be slackened by pressing the
adjuster(under the seat cover). Press the adjuster as
you grip the two Y-shaped belts with your another
hand.Pull the Y-shaped belt towards you to loose the
Y-shaped belts.
2: Tighten the Y-shaped belts. Pull the front upwards
until the Y-shaped belt is fully tightened. The Y-sha-
ped belt should be adjusted tightly without causing
discomfort to your child. A loose Y-shaped belt can
be dangerous.
Check the Y-shaped belt adjuster and tighten it each
time when the child is placed in the seat.
3.5 ADJUST THE HANDLE
The handle can be adjusted in 3 positions. At the
same time, hold the handle knob at both ends of the
handle, rotate the handle to the desired gear, and
release the handle adjusting button. Turn the handle
front and rear, make sure the handle is locked by the
handle adjusting button.
3.6 REMOVE THE BUCKLE
As shown in the picture, pass through the iron sheet
from the bottom hole back into the infant carrier,
and then the buckle can be removed.
3.7 INSTALL THE SUNROOF HOLDER (High version)
As shown in the picture, insert the bracket socket (e)
of the awning into the sockets ( f ) on both sides.
As shown in the picture, the expansion and contrac-
tion of the awning can be adjusted according to your
own situation.
Note: If you need to remove the awning, pls operated in
reverse according to the installation sequence of
the awning.
Note: The high version is equipped with aluminum hand-
les, and the awning can be used in the car.
3.8 ADJUST THE ISOFIX ATTACHMENTS
The ISOFIX attachments can be adjusted for many
positions to fit the different positions of ISOFIX low
anchorages expending from car seat. Press down the
release button to adjust ISOFIX attachment
of both sides to the longest.
Then put the ISOFIX attachments into guide sleeves,
and insert them into ISOFIX anchorages. Make sure
that you have heared a "click"and the ISOFIX latching
indication shows GREEN.
If you want to release the ISOFIX attachments, just
installation of the ISOFIX attachments is finished.
Push the red release button of the ISOFIX chuck at
the direction as shown, the ISOFIX chuck will be
released.
After installed the ISOFIX chuck, push the child
restraint forwards until it is tight against the car seat.
Now, the ISOFIX base is installed in place.
3.9 ADJUST THE LENGTH OF SUPPORT LEG
1: Take out the support leg from the lower cover
of the base, which keep about 90°to the base.
2: The method to adjust the length of the support
leg: Press and hold the adjustment button on the
support leg, then adjust the length up and down until
it hits the car ground. The bottom of the support leg
will turn green.
3.10 INSTALL / DISASSEMBLE THE INFANT CARRIER
AND BASE
1: How to install:
The base of the infant carrier has two shafts. Align
the two shafts with the slot of the base and place
EN
27