Table of Contents
Advertisement
Quick Links
Instructions
Hose Power
Controller Kit
For replacing the AmpLok
HV-20/35 Proportioners.
Kit 297983
For 230V and 380V H-20/35 Pro and HV-20/35 Models equipped with an AmpLok
Kit 261287
For 460V H-20/35 Pro Models equipped with an AmpLok
Important Safety Instructions
Read all warnings and instructions in manuals
311393, 63942-1, and 63942-ID.
Save these instructions.
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001
®
Hose Controller on H-20/35 Pro Proportioners and
®
®
Hose Controller.
311510A
Hose Controller.
Advertisement
Table of Contents
Related Manuals for Graco GUSMER 297983
Summary of Contents for Graco GUSMER 297983
- Page 1 For 460V H-20/35 Pro Models equipped with an AmpLok Hose Controller. Important Safety Instructions Read all warnings and instructions in manuals 311393, 63942-1, and 63942-ID. Save these instructions. Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001...
-
Page 2: Table Of Contents
Controller ....6 Graco Information ......10 Install Hose Power Controller Kit . -
Page 3: H-20/35 Pro Models
H-20/35 Pro Models H-20/35 Pro Models Installing this equipment requires access to parts that may cause electrical shock or other serious bodily injury if work is not performed properly. This work should be performed by a qualified electrician. Refer to H-20/35 Pro Proportioner Service manual 311393 for current unit schematics. -
Page 4: Install Hose Power Controller Kit
H-20/35 Pro Models Install Hose Power Controller Kit 3. Connect the white N wire to a neutral (N) terminal. See F . 3. Mount Hose Power Controller Mount new hose power controller to bracket using the following guidelines: • Use the #8 nuts and washers provided. •... - Page 5 H-20/35 Pro Models • Install sensor on cable, and reconnect cable to 4. Turn on hose zone control switch (green light). circuit breaker. 5. Test newly installed hose power controller. See F • Connect sensor black wire and white wire to ter- minals #15 and #16 on left side of hose power controller.
-
Page 6: Hv-20/35 Models
HV-20/35 Models HV-20/35 Models Installing this equipment requires access to parts that may cause electrical shock or other serious bodily injury if work is not performed properly. This work should be performed by a qualified electrician. Refer to HV-20/35 Series Proportioning Unit with ®... -
Page 7: Install Hose Power Controller Kit
HV-20/35 Models Install Hose Power Controller Kit 7. Connect D Sensor doughnut wires to terminals #15 and #16. Polarity does not have any affect. Before you can install the new hose power controller kit, 8. Connect blue 5 Vdc signal wires. Connect 3501 to it must be positioned properly. -
Page 8: Parts
Parts Parts Kit 297983 Kit 261287 For 230V and 380V H-20/35 Pro and HV-20/35 Models For 460V H-20/35 Pro Models Part No. Description Qty. Part No. Description Qty. 120387 CONTROL, heater, 240V 120404 CONTROL, heater, 480V 15H611 BRACKET, mount, heater control 15H611 BRACKET, mount, heater control 103229 SCREW, cap, SCH 103229 SCREW, cap, SCH... -
Page 9: Notes
Notes Notes 311510A... -
Page 10: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.