Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Yeti ASR
Summary of Contents for Yeti ASR
- Page 1 YETI ASR OWNER’S MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS OWNER’S MANUAL OVERVIEW FRAME FEATURES ASR GEOMETRY FRAME STANDARDS MAINTENANCE FRAME ASSEMBLY BEARING PRESS ASSEMBLY CABLE ROUTING SET-UP DROPPER POST INSERTION GUIDE EXPLODED VIEW REBUILD KITS FREQUENTLY ASKED QUESTIONS LIFETIME WARRANTY CONTACT INFORMATION... -
Page 3: Overview
Whether you are a beginner cyclist, or a seasoned pro, your Yeti bicycle will provide endless hours of two-wheeled fun. This model specific manual is designed to be used in conjunction with the general Yeti Owner’s Manual and the manuals supplied by the suspension manufacturers. If you did not receive the Yeti Owner’s Manual or the manual provided by the suspension manufacturer,... -
Page 4: Frame Features
This may be an “XC” bike, but it has the soul of an enduro machine. We know you’ll be without compromising any performance. riding it with a dropper post. TWO WATER BOTTLE MOUNTS The ASR is able to fit two water bottles inside the main frame to keep you hydrated on those extra big days. -
Page 5: Asr Geometry
GEOMETRY ASR OWNER’S MANUAL 12 0 M M F O R K S E AT T U B E L E N G T H E F F. T O P T U B E L E N G T H H E A D T U B E A N G L E ˚... -
Page 6: Frame Standards
FRAME STANDARDS OWNER’S MANUAL T R A V E L 115MM W H E E L S I Z E 29” F R A M E S I Z E XS, SM, MD, LG, XL R E A R S H O C K 190MM X 40MM B O T T O M B R A C K E T BSA 73MM... -
Page 7: Maintenance
It is important to remember that service intervals can specifications for individual parts on the ASR are listed below, as well as in the step by step vary depending on climate, trail conditions and riding frequency. Servicing your bike requires assembly instructions later in the manual. -
Page 8: Frame Assembly
Place a Double Port Clamp (3.18) into both Torque: 5 Nm (or hand tight) • 10mm guide pins WARNING: Service on Yeti bicycles requires covers. Secure with M4 x 25L FHCS (3.19). • 8mm guide pins special knowledge and tools. Yeti Cycles Tighten until snug. - Page 9 OWNER’S MANUAL QC CHECK Place 2x Race Extender (3.4) onto rear triangle Place 2x Race Extenders (3.9) onto the lower Install 2x Seat Stay Pivot Screws (3.6) from the inside of the Link and partially into the Rear Cycle rear triangle through to make sure motion main pivot bearings.
-
Page 10: Bearing Press Assembly
BEARING PRESS ASSEMBLY OWNER’S MANUAL LINK BEARING PRESS MAIN PIVOT BEARING PRESS Press both upper bearings into the link using a 10x19mm arbor. Support space between the tabs Press one bearing at a time using a 12x24mm arbor on the link while pressing bearings to ensure the link does not bend or get damaged. NOTE : Use caution when contacting the inside carbon face to avoid any damage to the Clean outer bearing race with alcohol and apply bearing retaining compound (Green 609 Loctite) paint. -
Page 11: Cable Routing Set-Up
CABLE ROUTING SET-UP OWNER’S MANUAL NON DRIVE CABLE ROUTING DRIVE SIDE CABLE ROUTING REAR BRAKE DROPPER REAR POST DERAILLEUR CABLED LOCKOUT FRONT TRIANGLE - REAR TRIANGLE VIEW FROM BOTTOM Route brake cable first through the nondrive side port in the rear tri, cable routing grommet, and REAR REAR the top port in the headtube. - Page 12 CABLE ROUTING SET-UP OWNER’S MANUAL DROPPER POST ROUTING SET-UP With a 3mm allen wrench, remove the lower Install your seatpost housing into the drive-side The hole under the downtube protector While pushing the housing into the head tube access door. head tube port, pushing until it exits near the provides an access point to use your finger to port, continue guiding the cable up the seat...
-
Page 13: Dropper Post Insertion Guide
Please confirm both of these measurements, they are both required to ensure proper X-SMALL dropper fitment. SMALL 287.5 If you have any questions, please contact Yeti or your local bike shop. FRAME SIZE MEDIUM LARGE X-LARGE *Subtract 34mm for a cabled dropper to accommodate housing bend angle. -
Page 14: Exploded View
3.33 3.30 3.18 3.17 3.37 3.19 ITEM NO. VIP/YETI PART NUMBER STOCK CODE DESCRIPTIO 14765 ASSY, ASR FT, T/C SER 3.24 EXTRA PARTS SUPPLIED IN HARDWARE KIT VIP (T/C) 3.22 12787 300040561 GUARD, DT, YETI (SL) 14770 300040569 PROTECTOR, DT, C... - Page 15 ASR FRONT TRIANGLE ASSEMBLY 3.20 300040563 ROUTING GROMMET, DUAL PORT, ASR 300040561 GUARD, DT, ASR 3.21 300060083 YETI SEAT COLLAR BOLT ON 36.4, T-SERIES BIKE YOKE SQUEEZY, 36.4 300040569 PROTECTOR, DT, CLEAR, ASR 3.22 300020056 BEARING, 6901-2RS, 12x24x6 3.23 300030357 SHCS, LOW PROFILE, M5 X 0.8, 16L...
-
Page 16: Rebuild Kits
ACCESS COVER, DOWN TUBE, ASR 300040561 DOWNTUBE GUARD, MY24 ASR 300040564 REAR TRIANGLE MAIN PIVOT GUARD, ASR 200020470 ASR 7075 ALLOY LINK W/ BEARINGS 2024-CURRENT 300040566 CHAINSTAY GUARD UPPER, ASR 200020469 ASR 6061 ALLOY LINK W/ BEARINGS 2024-CURRENT 200020480 ASR CHAINGUIDE REBUILD KIT 2024-CURRENT... - Page 17 TURQ Series bikes are manufactured with the highest quality and best-performing carbon fiber The short answer is the ASR can accept up to a 2.4” tire. There is great tire clearance on the ASR available and offer the perfect balance of stiffness, durability, and compliance. The result is a bike but tire sizes vary widely by manufacturers, so it is hard to give a number that works for all brands.
-
Page 18: Frequently Asked Questions
• Minimum Chainring Size: 28t (All sizes) on your saddle. Your local Yeti dealer can help you sort this out. We run 125mm drop on XS-SM Confused? Ask your local dealer or call us 303.278.6909. -
Page 19: Lifetime Warranty
Yeti Cycles is not responsible for any damages to you or others arising from riding, transporting or other use of your bicycle. In the event that your frame breaks or malfunctions, Yeti Cycles shall have no liability or obligation beyond the repair or replacement of your frame pursuant to the terms outlined in the warranty.