Sp L Ci F Icatio Ns - Wavetek 3001 Instruction Manual

1 .2 SP
E
CI
F
ICATIO
N
S
1 .2 .1
FRE
Q
UEN
CY
RA NGE
1 ΜΗτ (Model 30011 or 1 kHz (Model 3002) to 520 MHz selectable in
1 kH z steps .
RE ADOUT
6
d
igit
L
ever / Ιη dίεαιοι switc h es
RE
SO
LU
TIO
N
Ι
k
Η:
ACCUR ACY All modes (C W. AM an d FM) "0.001% after 15
m
in .
(Τγρ τ0 .002% after 2 hours with in 3 months of cali bration) . 00 .001%
τ 10 kH z when FREQUENCY VERN IER is not in CA L position, FRE .
QUENCY VERN IER ra nge is τ 5 kHz .)
STABI LITY
All
m
odes (C W, AM and FM) < 0.2 ppm/hour
(500 Hz per 10 min when FRE QUE NCY VERN I ER is not i n CA L
position Ι
PR OG RAMM A B I LITY Frequ ency is programmable via ιααr -ςιαπ e1 ίιιριιι connector
u
sing BC
D
.
coded TT L voltages or BCD-co ded contact clos ures (negative tr ue logic),
12 .2 RF
O
UTPU T
POWER LEVEL R ANG E +13 dΒm το 137 dBm (1io .03 μVRM 51
LEVEL CO NTR OL Co ntinuously adjustable in 10
d
θ steps with an 11 d8 VERNIER. Output
level is in dicated on α front-panel M
ETER cali b rated in volts RIMS and
d8m.
TOTA L LEVEL ACCUR ACY 4 13 to -7
d
8 m
t 1,25
d
8 (Typ τ0.75 dB)
7 to -77 d9 m
t 1 .95 dB (Τγρ s :1 .25 d
8)
-77 to -137 dB m
τ 2 .75 d
B ( Τγρ τ1 .5 d8)
Accuracy Brea kdow n Flatness ί+13 to .7 dB m) +0 .75 dB ΙΤγρ τ0 .5
d
8)
Output ME T ER 10 .5
d
e
Step Attenuator
τ0 .5 d8 το 70
d
β (t0 .2
d
8 calibr atio n er ror)
'-1 .0 d8 1υ 130
d
B (f0-5 dB calibration errorli
IMPE DA N C E 50 o hm s
SW R
" r
1 .2 at RF ουτρυι leνels below 0 1 VRMS
OU T PU T CONNECTO R
Τγρe Ν
RF I LE AKAG E < 1 μV is induced in α two-t urn, one-inch
d
iameter loop which is
h
eld
one inch away from any
s
urface.
L
oop feeds a 50 ohm receiver .
1 .2 .3
SPECT RA L PURITY
H
ARM ONIC OUTP UT < -30
d
8c from 10 to 520 ΜΗτ and from 1 kH z to 1 MHz (Model 3002)
< -26
d
Oc from 1 to 10 MHz
SUB - HARM ON ICS N
one detectable
1-2