Features This chapter includes: Introduction on page 1-2 ■ ■ Package Contents on page 1-2 ■ Hardware on page 1-3 Xerox WNA-100 Wireless Network Adapter...
The Wireless Network Adapter is a LAN bridge that transparently transmits network traffic from the wireless LAN to the wired network. It can be used with a large number of Xerox printers and multifunction devices and can also be configured to work in a large number of wireless environments.
Hardware Status LEDs The following table provides an overview of each LED: LED Number LED Definition Power Ethernet Xerox WNA-100 Wireless Network Adapter Color Description Green On: Power enabled. Orange Flashing: Internal error. Off: No power. Green On: 10/100 Base Tx Link.
Page 7
LED Number LED Definition Wireless Error Xerox WNA-100 Wireless Network Adapter Color Description Green On: Link > 11 Mbps. Green Flashing: Data > 11 Mbps. On: Link ≤ 11 Mbps. Orange Flashing: Data ≤ 11 Mbps. Orange Off: No Wireless network activity.
Page 8
Power Connector Only use the power adapter supplied with the Xerox Wireless Network Adapter. Ethernet Port Use the included Ethernet crossover cable to connect directly to your PC, and then your Ethernet enabled product. Default (Reset Button) A quick press of the Reset button prints a configuration page.
Configuring the Adapter This chapter includes: Setting Up the Adapter on page 2-2 ■ ■ Configuring the Adapter Using Your Web Browser ■ Configuring the Screens on page 2-6 Xerox WNA-100 Wireless Network Adapter on page 2-4...
Setting Up the Adapter To set up your Wireless Network Adapter: Connect the antenna to the adapter. Connect the power cord to the adapter. Xerox WNA-100 Wireless Network Adapter Setting Up the Adapter...
Page 11
The adapter is not intended for use on a switch or hub. The adapter is expecting to be connected to a single device using the Ethernet crossover cable provided. See also: Installation Guide at www.xerox.com/office/wna Xerox WNA-100 Wireless Network Adapter Setting Up the Adapter...
Click the Restart button in the Reset section of the Administrative Utilities page. Xerox WNA-100 Wireless Network Adapter Configuring the Adapter Using Your Web Browser on page 1-5 for more information.
Use a wireless repeater to extend the range of your wireless adapter. ■ Avoid using cell phones or other wireless electronics nearby. Xerox WNA-100 Wireless Network Adapter Configuring the Adapter Using Your Web Browser Hardware on page 1-3 for more information.
SSL (HTTPS) Settings: Secure HTTP allows you to encrypt the transmission to the device during configuration. ■ SNMP Settings (Simple Network Management Protocol): Allows you to use standard SNMP tools to configure the wireless interface. Xerox WNA-100 Wireless Network Adapter Configuring the Screens...
Default Configuration Interface: Allows you to change the default configuration interface. ■ Reset: Allows you to reset the interface or configuration. Support The Support page lists helpful links on the Xerox website. Xerox WNA-100 Wireless Network Adapter Configuring the Screens...
Troubleshooting This chapter includes: Troubleshooting Wireless Configuration Problems ■ See also: Online Support Assistant at www.xerox.com/office/wna Xerox WNA-100 Wireless Network Adapter on page 3-2...
If you are connected to a printer, you can print an adapter configuration page with a short click of the Reset button. ■ Is the correct IP address in the browser? Does the IP address match the IP address of the adapter? Xerox WNA-100 Wireless Network Adapter Troubleshooting Wireless Configuration Problems on page 2-4...
Online Support Assistant The Online Support Assistant is a knowledge base that provides instructions and troubleshooting help to solve your adapter problems. To access the Online Support Assistant, go to www.xerox.com/office/wna. Xerox WNA-100 Wireless Network Adapter Troubleshooting Wireless Configuration Problems...
Operating: 10% – 90% non-condensing (40% – 60% recommended) Electrical Specifications Available in three configurations: ■ North America: Part number 097S03740 United Kingdom: Part number 097S03741 (available in 2007) ■ ■ European Union: Part number 097S03742 (available in 2007) Xerox WNA-100 Wireless Network Adapter...
Page 20
■ Minimum: 16 dBm at 54 Mbps Controller Specifications 166 MHz processor ■ Memory 2 MB of flash memory ■ ■ 4 MB of SDRAM Interfaces ■ Ethernet 10 Base T and 100 Base Tx Xerox WNA-100 Wireless Network Adapter...
Page 21
Security and Regulations Xerox has tested this product to electromagnetic emission and immunity standards. These standards are designed to mitigate interference caused or received by this product in a typical office environment. Information for United States Users This equipment has been tested and found to comply within the limits for Class B digital device pursuant to Part 15 of the FCC Rules.
Page 22
According to 47CFR, Part 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers, Xerox declares under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device FOR HOME OR OFFICE USE.
Page 23
(pacemakers, hearing aids, etc.) regarding any restrictions on the use of 802.11x wireless technology. Xerox Corporation cannot be responsible for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product. Declaration of Conformity (CE) Product: Ethernet and Wireless 802.11a, 802.11b, and 802.11g-enabled print server...