PS2900H Note:PS2900H = PS2900H-M+PS2900H-S The battery chemistry of these products is Lithium Iron Phosphate. This manual is designed for qualified personnel only. The tasks described in this document should be performed by authorized and qualified technicians only.
· Do not connect different battery types together. · Please ensure that all the batteries are grounded properly. · Do not open the battery to repair or disassemble. Only Energizer Solar is allowed to carry out any such repairs. · In case of fire, use only dry powder fire extinguisher. Liquid extinguishers should not be used.
1. PS2900H-S is the battery module, and PS2900H-M includes system controller and battery module; 2. PS2900H-M contains the controller of the entire system, so each system must have one PS2900H-M; 3. Our system consists of at least 1 PS2900H-M +1 PS2900H-S and up to 1 PS2900H-M +6 PS2900H-S. 5.1 PS2900H-S Specifications Specifications for PS2900H-S Model NO.
Ground Fault, Over Temp, In rush current · Battery Protection: Internal Short Circuit, Over voltage, over current, over temp, Under voltage The battery system contains the following Interface to allow it to connect and operate efficiently. PS2900H-S Features: - interface: PS2900H-M Features:...
6.2 Monitoring Methods Battery system remote monitoring available via inverter app. 7. Installation 7.1 Items in the package Please check if following items are including with the package: For PS2900H-S Items Quick Mounting screw pack Installation Installation guide...
Items Items Mounting screw pack DC output cable Fixing bracket Installation guide Footstand Expansion tube*2 & Expansion screw*2 Communication cable (BMS-Inverter) Waterproof cover Grounding cable RJ45 7.2 Installation Precaution Make sure the installation site meets the following conditions: Not in direct sunlight. Not in areas where highly flammable materials are stored.
7.5 Installation Steps PS2900H-S Step 1: Install a PS2900H-S with four footstand (Item E) and place it on the ground and adjust it to the level. After installing the footstand, use a track level bar to confirm the level. Insert the waterproof cover...
Page 11
Step 2: Place the battery 20mm against the wall. Note: Please make sure the Operating Status LED is on your left handside when you facing the battery model. Step 3: Stack the batteries one by one. Step 4: Place the two fixing brackets (Item D) close to the wall and install them on both sides of the battery. Step 5: Mark the wall through the bracket hole.
Page 12
Step 6: Punch after removing the PS2900H-M. Drill holes with electric drill, make sure the holes are at least 50mm deep, and then tighten the expansion tubes (Item J). Step 7: After stacking PS2900H-M again, fix the battery on the wall.
Page 13
Step 8: Fix the mounting screw packs (Item C) on both sides of the battery, the installation is over. Note: Please make sure each system including 1 PS2900H-M and 1 PS2900H-S. PS2900H-S less than 6(1~6) pieces: PS2900H-S Total of 6...
Follow the stePS2900H-S below to securely connect the PS2900H-M power cable. Step 1: Connect the supplied power cable to the DC connectors of the PS2900H-M module. The DC+ is connected to the PS2900H-M+ connector and the DC- is connected to the PS2900H-M- connector.
Step 2: Crimp the cable with a Rj45 plug which is inside of the cable connector. B: Connect the grounding cable to ensure that all batteries are grounded. Wiring shall be connected in the sequence as shown in below. 7.7 System Start up ·...
8. Commissioning The operating status light on the left side of the battery pack shows its working status. For PS2900H-S Green LED Red LED Batteries Status On for 0.5s, Off for 0.5s On for 0.5s, Off for 0.5s Runing in boot On for 0.1s, Off for 0.1s...
Page 17
Fault Green LED Red LED LED4-1 Under voltage fault ■ ● Over voltage fault ■ ● Over temperature fault ■ ● ● Under temperature fault ■ ● Discharge over current ■ ● ● Charge over current ■ ● ● Discharge over power ■...
· In case of force majeure (ex: lightning, storm, flood, fire, earthquake, etc.). · There are no warranties-implied or express-other than those stipulated herein.Energizer Solar orEnergizer Solar shall not be liable for any consequential or indirect damages arising or in connection with the product specification, battery or pack.
11.2 Troubleshooting When the red / green LED on the panel is flashing or normally on, it does not mean that the PS2900H-S is abnormal, it may be just an alarm or protection. Please check the ‘LED status indicators’ in chapter 7 for the detailed faulty definition before any trouble-shooting steps PS2900H-S.