Table of Contents
Advertisement
VHF Radio Information
This product may be used only on specific radio frequencies,
which vary depending on the country of use. The handheld
device and the dog device allow the user to install a different
antenna. Changing the antenna can result in improved radio
performance and higher radiated power. You must not use the
device with a third party antenna or an antenna not approved by
Garmin
®
. Go to
www.garmin.com/tracking-legal
the performance and radio frequency of this product, lawful
accessories, and power limits for countries.
Adding a Dog to the Atemos 100 Handheld Using
Wireless Pairing
1
If the dog collar device is on, turn off the dog collar device
(Turning Off the Devices, page
2
Hold
until the dog collar device emits two series of beeps
(about 2 seconds), and then release .
The status LED flashes rapidly in green. The dog collar
device is now ready to be linked, or paired, with a handheld
device.
3
On the handheld device, select Dog List > Add Dog.
4
Bring the dog collar device near the handheld device, and
select Yes.
5
After successfully adding the dog collar device, enter the
name of the dog, and select
Adding a Dog Using the Track and Control Codes
NOTE: This feature varies based on dog collar device type and
feature availability in your area.
Before you can add a dog using the track and control codes, the
dog owner must find the track and control codes
Dog ID and Track and Control Codes, page
to you.
You can use track and control codes to authorize a handheld
device to interact with your dog collar device. If you are not near
the dog you want to add or you cannot put the collar into pairing
mode, you can add the dog using the track and control codes.
1
Select Add Dog.
2
When asked if you are near the collar, select No.
3
When asked if you know the track and control codes, select
Yes.
4
Enter the track or control code for the collar, and select
The dog's track code allows you to track the dog. The dog's
control code allows you to both track and train (correct) the
dog.
5
Enter the name of the dog, and select OK.
Finding the Dog ID and Track and Control Codes
You can share a dog's track code so another person can track
your dog. Also, you can share a dog's control code so another
person can track and train (correct) your dog.
1
Select Dog List.
2
Select a dog.
3
Select Show Info.
Editing Dog Information
Resetting a Dog's Statistics and Track
You might want to clear the dog statistics and track before a
new hunt.
1
Select Dog List.
2
Select a dog.
3
Select Show Info > Reset > Yes.
Dog Collar Device Setup
for details about
2).
> OK.
(Finding the
3) and tell them
.
Changing the Length of the Dog's Track
You can adjust the length of the dog's tracks shown on the map.
Showing less tracks on the map can help to declutter the map
view. Changing the length of the track shown on the map does
not affect the tracks stored in the internal memory.
1
Select Setup > Dogs > Dog Track On Map.
2
Select an option to show more or less of the tracks on the
map.
Changing the Dog Name
1
Select Dog List.
2
Select a dog.
3
Select Show Info.
4
Select the dog's name.
5
Enter the name, and select
Changing the Color of the Dog's Track
You can change the track color of the dog. It is helpful to have
the track color match the color of the collar strap, if possible.
1
Select Dog List.
2
Select a dog.
3
Select Show Info.
4
Select the colored square next to the dog's name.
5
Select a color.
Changing the Dog Type
Before you can change the dog type, the collar must be turned
on and within range of the handheld device.
1
Select Dog List.
2
Select a dog.
3
Select Show Info >
> Change Dog Type.
4
Select a dog type.
Changing the Dog ID
Before you can change the dog ID, the collar must be turned on
and within range of the handheld device.
If you are experiencing interference from other collars or
handheld devices in the area, you might need to change the ID
for the dog.
1
Select Dog List.
2
Select a dog.
3
Select Show Info.
4
Select
> Change ID.
5
Select an available ID.
If another handheld device is tracking this dog, for best results,
remove the dog from the device, and use the track and control
codes to add the dog again
Control Codes, page
3).
Setting Dog Alerts
You can adjust how the handheld device alerts you to certain
actions of the dog.
1
Select Setup > Dogs > Dog Alerts.
2
Select an action.
3
Select the method the device uses to alert you for this action.
4
Repeat steps 2 and 3 as needed.
Removing a Dog
1
Select Dog List.
2
Select a dog.
3
Select Remove.
> OK.
(Adding a Dog Using the Track and
3
Advertisement
Table of Contents
