Important Safety Instructions - Schartec Move 3 Series Manual

Please read the manual carefully before you begin the installation and use of the opener. The installation of your new garage door opener must
be performed by a competent expert or a specialist company. A competent person is, in accordance with EN 12635, considered a person who has
appropriate training, qualified knowledge and practical experience in order to mount and maintain a door system properly and safely. The installa-
tion or repair without technical qualifications can lead to property damage, serious injury, and/or death.
Dear Customer
Thank you for choosing a quality product from the Schartec brand. Thanks to our unique quality management system, as well as continuous
product development, Schartec garage door openers meet the highest standards of quality and comfort. We thank you for your trust and wish you
much pleasure with your new Schartec garage door opener.
Declaration of Conformity (CE)
Schartec Move garage door openers meet the requirements of the applicable European and national directives. Conformity has been proven, the
corresponding declarations, certificates, test reports and documents can be requested at info@schartec.de. The Declaration of Conformity can
also be found on page 32. The supplied radio system type T-11 (Art.No.ST801007) complies with Directive 2014/53/EU. The full text of the EU Dec-
laration of Conformity is available at the following Internet address: www.schartec.de
1. Intended use
The garage door opener is intended exclusively for the impulse operation of spring-balanced sectional and up-and-over doors in the private/
non-commercial sector. Door systems that are located in the public area and only have a protective device, e.g. force limiter, may only be operat-
ed under supervision. The garage door opener is designed for operation in dry rooms.
2. Non-intended use
The garage door opener must not be used for purposes other than garage door opener automation. Continuous operation and use in commercial
areas is not permitted. The opener must not be used on doors without fall protection.
3. Qualification of the fitter and installer
Only correct installation and maintenance by a competent/knowledgeable company or a competent/knowledgeable person in accordance with
the instructions can ensure the safe and intended functioning of an installation. According to EN 12635, a competent person is a person who has
suitable training, qualified knowledge and practical experience to correctly and safely assemble, inspect and maintain a garage door system.
4. Safety instructions for assembly, repair, maintenance and disassembly of the garage door system
DANGER!
Balancing springs are under high tension
Adjusting or loosening the balancing springs can cause serious injuries! For your own safety, only have work on the balancing springs of the door
and, if necessary, maintenance and repair work carried out by an expert! Never attempt to replace, readjust, repair or relocate the balancing
springs of the door or their brackets yourself. Also check the entire garage door system (joints, door bearings, cables, springs and fastening parts)
for wear and possible damage. Check for existing rust, corrosion, and cracks. Faults in the garage door system or misaligned doors can result in
serious injury! Do not use the garage door system if repair or adjustment work has to be carried out!
Mains voltage
In case of contact with the mains voltage, there is a risk of fatal electric shock. It is therefore essential that you observe the following instructions:
Electrical connections may only be carried out by a qualified electrician. The on-site electrical installation must comply with the relevant protec-
tion regulations (230/240 V AC, 50/60 Hz). Disconnect the mains plug before carrying out any work on the opener.
WARNING!
Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Warranty conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Before installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Connection of external controls and accessories . . . . . . . . . . . . . . . . . . . .28
Manual unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Troubleshooting cont. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Important safety instructions

WARNING
Contents
18