Maytag MHN30PD Installation Instructions Manual page 14

CODE EXPLANATION CODE EXPLANATION
H. 01 SUPER CYCLE UPGRADE PRICE
(Skipped unless super cycle pricing is enabled.)
H. 01 This represents the number of coin 1 required to
upgrade a base cycle to a super cycle. Advance
from 0-39 by pressing the PERM. PRESS button.
-> Press the DELICATES AND KNITS button once
to advance to next code.
h. 01 SUPER CYCLE TYPE
(Skipped unless Super Cycle pricing is enabled.)
h. 01 This represents the Super Cycle upgrade option.
Press the PERM. PRESS button to step through
upgrade options 1-3 as follows:
01 - enhanced wash, extra 3 minutes of wash
tumble in addition to the programmed wash time.
02 - extra rinse for all cycles.
03 - both 01 and 02.
--> Press the DELICATES AND KNITS button once
to advance to next code.
t t
J. Cd COiN/DEBIT OPTION
J. Cd Both coin & debit selected. Press the QUICK
CYCLE button 3 consecutive times to change this
selection.
J. C_ Coins selected, debit disabled. Press the QUICK
CYCLE button 3 consecutive times to change this
selection.
J. _d Debit card selected, coins disabled. This is the
factory default for PN models. Press the QUICK
CYCLE button 3 consecutive times to change this
selection.
J. Ed Enhanced Debit is self-selected when a
Generation 2 card reader is installed in the
washer. The Ed option cannot be manually
selected or deselected.
--> Press the DELICATES AND KNITS button once
to advance to next code.
L. 00 PRICE SUPPRESSION OPTION
This option causes the customer display to show
'ADD' or 'AVAILABLE' rather than the amount of
money to add. (Used mainly in debit installations.)
L. 00 Not Selected 'OFR'
h PS Selected 'ON.' Press the QUICK CYCLE button
once for this selection.
--> Press the DELICATES AND KN{TS button once
to advance to next code.
n. CE CLEAR ESCROW OPTION
When selected, money held in escrow for
30 minutes without further escrow or cycle
activity will be cleared.
00 Not Selected 'OFF'.
r. 800
r. 800
TOP SPIN SPEED RPM
This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm. Step between speeds by
pressing the PERM. PRESS button. Factory
pre-set for 800 rpm.
--> Press the DELICATES AND KNITS button once
to advance to next code.
i,
U. 00 PENNY iNCREMENT OFFSET
U. 00 This option is not supported for European Models
and the value must be set to 00.
A1.
--> Press the DELICATES AND KNITS button once
to advance to next code.
00 PREWASH LENGTH
Choose 0 to disable the prewash or select
between 2 and 7 minutes by pressing the PERM.
PRESS button.
--> Press the DELICATES AND KNITS button once
to advance to next code.
A2. 03 FINAL SPIN LENGTH
A2. 03 This is the number of minutes of final high speed
spin. Choose from 3-8 minutes by pressing the
PERM. PRESS button.
--> Press the DELICATES AND KNITS button once
to advance to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Number of cycles in HUNDREDS. 1 02 = 200
2 00 Number of cycles in ONES. 2 2.5 = 25
TOTAL CYCLES = 225
This is 'VIEW ONLY' and cannot be cleared.
--> Press the DELICATES AND KNITS button once to
advance to next code.
If money counter (1.00 or 1.00) is selected, the following
is true:
3 00 Currency amount in HUNDREDS.
4 00 Currency amount in ONES.
5 00 Currency amount in HUNDREDTHS.
END OF SET-UP PROCEDURES
301=100.00
4 68 = 68.00
5 7.5= 00.75
TOTAL = 168.75
EXIT FROM SET-UP MODE
[] PD Models: Reinstall access door.
[] PN MODELS WiTH PROGRAMMING SWITCH:
Turn key clockwise and remove.
CE Selected 'ON'. Press the QUICK CYCLE button
once for this selection.
--> Press the DELICATES AND KNITS button once
to advance to next code.
14