PRODUCT FEATURES
- Full spectrum aquarium light: Light promotes optimal coral growth, enhances coral's vibrant colors, and creates a soft glow throughout the aquarium.
- Smart fan for light temperature control: The integrated fan effectively dissipates excess heat, maintaining an optimal light temperature.
- Adjustable Light Height: By lengthening or shortening the line on the light, and adjusting the height of the bracket to determine the appropriate light height.
- Suitable for tanks less than 0.80 inches thick: This LED aquarium light is compatible with most rimmed and rimless tanks with glass up to 0.80 inches thick.
PRODUCT PARAMETERS
Model | Output Voltage | Power | Led Quantity | Light Size | Suitable Tank Size | Power Cord |
HG107 | DC24V | 50W | 56PCS | 3.70" (9.4cm) | 24"x24"x24" (61 cm x61 cm x61cm) | 4.92ft+2.96ft (1.5m+1m) |
PRODUCT DETAILS
![HYGGER - HG-107 - Product overview Product overview]()
INSTALLATION INSTRUCTION
- Take products and accessories out of the package.
- Install screws
on the base, take
bracket, align the end of the band gap with the two holes of the base, and screw down with screws
.
![HYGGER - HG-107 - Installation - Step 1 - Install screws on the base Installation - Step 1 - Install screws on the base]()
- Connect
bracket, align the gap of
bracket with the screw holes of
bracket, adjust the required length, and screw down with screws. - Take the
bracket, and attach the screw holes of the
bracket to the screw holes of the
bracket and screw down with screws
.
![HYGGER - HG-107 - Installation - Step 2 - Take the bracket Installation - Step 2 - Take the bracket]()
- Loop the wire on the light through the gap in the bracket, adjust to a suitable length, and tighten the wire lock with a screw.
![HYGGER - HG-107 - Installation - Step 3 Installation - Step 3]()
- Run the wire around the bend of the bracket head and secure the wire and lamp wire with clamps.
![HYGGER - HG-107 - Installation - Step 4 Installation - Step 4]()
- Connect the extension cable for the light and the extension cable for the power adapter.
![HYGGER - HG-107 - Installation - Step 5 Installation - Step 5]()
- Loosen the base knob to match the tank thickness and install it securely in the fish tank.
![HYGGER - HG-107 - Installation - Step 6 - Loosen the base knob Installation - Step 6 - Loosen the base knob]()
- Finally, plug in the power supply and select the desired light settings.
OPERATION METHOD
- The light offers five levels of brightness adjustment: 100%-77%-55% -32%-10%, cycling from the darkest to the brightest. It also offers three color options: blue, white, and warm white. Additionally, you can set the duration of the light with three time settings: 6H, 9H, and 12H.
- DIY mode setting:
Press the "color setting" button to set the desired color. After the color setting is completed, press the "brightness" button
to adjust the brightness. Finally, press the "time" button
to set the desired time. The light will come on according to the color, brightness and time you set.
Attention: When you press the "6H", the indicator is yellow, and "9H" is green, "12H" is red.
6H timing: The yellow light on the controller indicates that the 6-hour timing mode is on, and the cycle is 24 hours. The light will work according to the set color and brightness for 6 hours and then turn off automatically and turn on at the same time the next day.
9H timing: The green light on the controller indicates that the 9-hour timing mode is on for a 24-hour cycle. The light will work according to the set color and brightness for 9 hours and then turn off automatically and turn on again at the same time the next day.
12H timing: The red light on the controller indicates that the 12-hour timing mode is on for a 24-hour cycle. The light will work according to the set color and brightness for 12 hours and then turn off automatically and turn on again at the same time the next day.
PACKING LIST
1 x User manual
1 x Light
1 x Power adapter
1 x Controller
3x Clamp (2 spare parts)
3x Bracket
8x Screw
1 x Hex wrench
1 x Base
![]()
To avoid possible electrical shock, do not immerse the switch in water. If the switch falls into the water or otherwise becomes wet, do not touch it until you have unplugged it. Basic safety precautions should be observed including the following:
- Read and follow this user manual strictly.
![]()
To avoid possible electric shock, special care should be taken. For each of the following situations, do not attempt to repair yourself; return the light to an authorized service facility for service or discard the light. - Carefully examine the light after installation. It should not be plugged in if there is water on parts not intended to be wet.
- Do not operate the light if it has a damaged cord or plug, if it is malfunctioning or if it is dropped or damaged in any manner. The power cord of this light cannot be replaced, if the cord is damaged, the light should be discarded.
- To avoid the possibility of the light plug getting wet, position the aquarium stand and tank to one side of a wall-mounted receptacle to prevent water from dripping onto the receptacle or plug. A "drip loop", shown in the figure below, should be arranged by the user for each cord connecting the light to the receptacle. The "drip loop" is the part of the cord below the level of the receptacle or the connector. If an extension cord is used, to prevent water from traveling along the cord and coming in contact with the receptacle. Ifthe plug or receptacle does get wet, DO NOT unplug the cord. Disconnect the fuse to the circuit breaker that supplies power to the light. Then unplug and examine for the presence of water in the receptacle.
![]()
- Close supervision is necessary when the light is used near children.
- To avoid injury, do not touch moving or hot parts.
- Make sure the light is securely installed before operating it.
- Read and observe all the important notices on the light.
- 1f an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.
- The light is intended FOR HOUSEHOLD USE ONLY.
Distributed by: Hygger Aquarium, Inc.
13941 Magnolia Ave, Chino, CA 91710
Contact us at www.hygger-online.com
Email: mago@hygger-online.com
![]()
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Need help?
Do you have a question about the HG-107 and is the answer not in the manual?
Questions and answers