Aqueon OptiBright+ - LED Aquarium Light Manual

PRODUCT INSTALLATION INSTRUCTIONS

• This product is recommended for use over glass-covered aquariums.
• Aqueon glass covers fit on the inside lip of the aquarium to prevent seepage out of the aquarium.
  

1. Position the fixture over aquarium by adjusting the legs (Fig 1) to the proper length so they securely hold the fixture in place. Always center the fixture so that it provides maximum exposure of light to all aquarium inhabitants.
   
2. Connect the transformer to the connector on the side of the light fixture.
3. Plug the transformer into an acceptable outlet. Be sure to incorporate a "drip loop" to prevent water droplets from running down the cord and into the outlet should any water get onto the cord.
4. The light fixture will turn on to a standard setting and you can program the fixture to your preferred settings using the included remote. (Initial standard setting is set to white LED, blue LED and purple RGB.)

*Average output @ 12"

REMOTE LAYOUT

On/Off
Use when setting the timer function for White, Blue and RGBs to be on or off

Adjust Brightness
Color intensity can be increased or decreased in 10% increments

LCD screen will indicate the time of day (AM/PM) as well as which lights are on: W/B/RGB

Set/Enter
Use when setting the time and storing the timer function for White, Blue and RGBs

RGB Scroll
Scroll through RGB colors in 3 different speeds.

RGB On/Off
What is RGB?
Red, green and blue LEDs are mixed together to create a broad array of colors. 8 preset options were created for quick customization.

REMOTE INSTRUCTIONS

Installing the Batteries

1. Remove the cover from the back of the remote.
2. Install 2 (AAA) batteries (included).
3. Close the cover – the remote is now ready for use.

Setting the Time

1. Press and hold for 3 seconds until you see the hour blinking
2. Use the and buttons to set the hour – 'AM/PM' will be displayed on the screen.
3. Press . The minutes will be blinking. Use the and buttons to set the minute.
4. Press . The time will be set.

Programming Desired Color Options

Set the fixture to the desired color combination by following the steps below:

1. Setting the White LEDs
   1. Press to turn the White LEDs on – 'W' will be displayed on the screen.
   2. Use the and buttons to adjust the color intensity of the White LEDs only.
   3. Press to turn the White LEDs off.
2. Setting the Blue LEDs
   1. Press to turn the Blue LEDs on – 'B' will be displayed on the screen.
   2. Use the and buttons to adjust the color intensity of the Blue LEDs only.
   3. Press to turn the Blue LEDs off.
3. Setting the RGB LED Color Option
   1. Press one of the 8 preset color options to turn the RGBs on – 'RGB' will be displayed on the screen.
   2. Use the and buttons to adjust the color intensity of the RGBs only.
   3. Press to turn the RGBs off.

Note: To program different color intensities for each of the White, Blue and RGBs – each specific color must be on by itself. If all three colors (or two) are on at the same time the intensity will be adjusted for all 3 colors to the same intensity. Ex: If you see 'W' on the screen and you use the and buttons, the color intensity will be adjusted for only the White LEDs. If you see 'W' and 'B' on the screen and you use the and buttons, the color intensity will be adjusted for the same amount for both the White AND Blue LEDs.

Programming the Timer

Note: Make sure your desired colors are in the 'ON' setting before you start programming the timer. 'W', 'B' and 'RGB' should be displayed on the screen.

1. Press and hold for 3 seconds until you see the hour blinking.
2. Press twice – you will see 'W' and 'ON' on the screen to set the White LEDs ON.
3. Use the and buttons to set the hour – 'AM/PM' will be displayed on the screen.
4. Press . The minutes will be blinking. Use the and buttons to set the minute.
5. Press – you will see 'W' and 'OFF' on the screen to set the White LEDs OFF. Repeat steps 3-4.
6. Press – you will see 'B' and 'ON' on the screen to set the Blue LEDs ON. Repeat steps 3-4.
7. Press – you will see 'B' and 'OFF' on the screen to set the Blue LEDs OFF. Repeat steps 3-4.
8. Press – you will see 'RGB' and 'ON' on the screen to set the RGBs ON. Repeat steps 3-4.
9. Press – you will see 'RGB' and 'OFF' on the screen to set the RGBs OFF. Repeat steps 3-4.
10. Press – your fixture is now programmed to your custom settings.

Note: If you don't want to set the LEDs to turn on/off you can leave them both at 12:00AM.

RGB LED Scroll Mode

1. Press to scroll through the different color options at different speeds.
   1. 25 – Color will change every 5 seconds.
   2. 50 – Color will change every 4 seconds.
   3. 75 – Color will change every 3 seconds.
   4. 100 – Color will stop scrolling and be set to the color you selected.

IMPORTANT CLEANING & SERVICING PRECAUTIONS

CLEANING:
It is important to keep this appliance clean. Unplug and remove the unit from the aquarium. Wipe exposed surfaces carefully with a damp cloth to remove any dust or mineral deposits which may collect over time. Make sure all surfaces are dry before reinstalling.

SERVICING:
In order to assure proper electrical connections and polarity, replacement parts and servicing should be performed only by a qualified electrician.

IMPORTANT SAFETY INSTRUCTIONS

To guard against injury, basic safety precautions should be observed including the following:

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2. 
   To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment. For each of the following situations, do not attempt to repair yourself; return the appliance to an authorized service facility for service or discard the appliance.
   1. If the appliance falls into the water, DO NOT reach for it! First unplug it and then retrieve it. If electrical components of the appliance get wet, unplug the appliance immediately.
   2. Carefully examine the appliance after installation. It should not be plugged in if there is water on the parts not intended to be wet.
   3. Do not operate any appliance if it has a damaged cord or plug, if it is malfunctioning or if it is dropped or damaged in any manner.
   4. To avoid the possibility of the appliance plug getting wet, position aquarium stand and tank to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug. A "drip loop", shown in the figure below, should be arranged by the user for each cord connecting an aquarium appliance to the receptacle. The "drip loop" is the part of the cord below the level of the receptacle, or the connector if an extension cord is used, to prevent water traveling along the cord and coming in contact with the receptacle. If the plug or receptacle does get wet, DO NOT unplug the cord. Disconnect the fuse to the circuit breaker that supplies power to the appliance. Then unplug and examine for the presence of water in the receptacle.
      
3. Close supervision is necessary when any appliance is used by or near children.
4. To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs, and the like.
5. Always unplug the appliance from the outlet when not in use, before putting on or taking off parts, and before cleaning. Never yank the cord to pull plug from outlet. Grasp the plug and pull to disconnect.
6. Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition.
7. Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing.
8. Make sure an appliance mounted on a tank is securely installed before operating it.
9. Read and observe all the important notices on the appliance.
10. If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.
11. This appliance is recommended for use over a glass aquarium cover or panel. The appliance is intended FOR HOUSEHOLD USE ONLY.
12. SAVE THESE INSTRUCTIONS.

LIMITED WARRANTY

Any notice to Central Aquatics must be delivered by United States or electronic mail to one of the following addresses:
U.S. Mail: Central Aquatics - Aqueon, 5401 West Oakwood Park Drive, Franklin, Wisconsin 53132
Electronic Mail: info@central-aquatics.com

For additional information regarding this limited warranty, please contact us at the addresses above, or call us at 888-255-4527.

Central Aquatics
5401 West Oakwood Park Drive
Franklin, WI 53132

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Aqueon OptiBright+ - LED Aquarium Light Manual