Table of Contents
Advertisement
RET Button – Use to Retract either slideouts or awnings.
•
Use in conjunction with the arrow buttons to select an awning or
slideout (also used when pairing wall mounted remotes to the
system).
Menu Display (between arrow buttons) use the arrow keys to
scroll through the selections.
•
Menu Display shows A1 or A2 (awnings). Cycle between
awnings with the arrows. Press and hold EXT or RET to
extend or retract the selected awning.
•
Menu Display shows S1, S2, S3 or S4 (slideouts). Cycle
between slides using the arrow buttons. Press and hold EXT or
RET to extend or retract the selected slideout.
•
Menu Display shows OF (OFF). Pressing the EXT button turns
off all lights,fans, and the touchscreen). This does not shut down
the generator. Press any of the numbered light buttons to turn
the touchscreen back on.
•
Menu Display shows PA (pair). Press EXT to pair your phone
or tablet or press RET to pair one of the wall mounted remote
controls. The PA on the small display will flash on and off
indicating the system is in pairing mode and can be connected to
a Bluetooth smart device. When the device is paired, PA display
will go out.
Pairing a Smart Device to the JAYCOMMAND/TravelLINK App
Download and install the JAYCOMMAND/TravelLINK app from the
Google Play or Apple App Store. Follow the instructions in the app to
connect to the system. Up to (3) personal Bluetooth devices can be
connected to the JAYCOMMAND/TravelLINK system at the same
time.
The JAYCOMMAND/TravelLINK "Motors" screen automatically
locks on your smart device after connecting to the app to prevent
inadvertent operation of the systems in the RV. The lockout indicator
on the screen must be swiped to unlock the motor controls. When
operating any motor control, the system locks out all other control
devices (e.g. smartphone or command panel) until the motorized
device in use has stopped.
Heating/Cooling operation
There are no thermostats located in the RV. Heating and cooling
is controlled through the BMPRO JAYCOMMAND/TravelLINK
touchscreen Climate screen. One or more small sensors are located
on the walls of the RV. These sensors work with the touchscreen to
monitor the temperature in an area of the RV and adjust according to
climate settings on the touchscreen.
Home Screen
Shows an overview of the key features of your RV: climate, lights,
motors, tanks and energy.
Water Screen
Shows tank monitors (black, gray, fresh) water pump switch, water
heater switches for gas and electric and possibly the tank heater
switch.
Page 42
ELECTRICAL
Motors Screen
Shows controls for the leveling system, awnings, slideouts, jacks and
the ramp door (if applicable).
•
The app on your smart device automatically locks out the Motors
screen on your device. You must swipe to unlock the screen in
order to operate motors.
•
Only one motor may be operated at a time.
•
When a motor is in operation, motor control is disabled on any
other device running the JAYCOMMAND/TravelLINK app.
Climate Screen
Shows the thermostat to control heating and cooling and fan speed.
Lights Screen
Turn lights on and off as well as dim certain lighting with sliders.
Energy Center Screen
Shows generator on/off, AGS (auto generator start), battery levels,
Inverter on/off, solar data, and fuel levels.
Fans and Vents Screen
Shows kitchen and bath fans and automatic vents (if equipped). Turn
fans on and off, and open and close automatic vents.
System Switches (remote controls)
The system will come with multiple individual smart
remote controls installed on the wall in each room.
The smart RV system remote controls use a 3-volt
Lithium CR2032 coin cell battery.
To access the battery on the back of the remote,
remove the remote from the wall:
1.
Pull the bottom of the remote away from the wall. There will be
an audible snap as it releases from the clip.
2.
Lift the remote upwards to unhook it at the top.
3.
The remote will separate from the wall mount.
To replace the remote on the wall:
1.
Hook the top of the remote on the top of the wall bracket.
2.
Push the bottom of the remote back in place. There will be an
audible snap as it attaches to the mount.
Tire Pressure Monitor System (TPMS)
Depending on your model, you may have a Tire
Pressure Monitor System (TPMS). The TPMS
system is monitored by sensors paired to the
system through the touchscreen. The TPMS
System comes with sensors that screw on to the
valve stem either inside or on the outside of each
tire. The sensors are programmed according to
their tire position on the trailer, and not to each
individual tire.
(See page 54)
External TPMS Sensor
Advertisement
Table of Contents
