Table of Contents
Advertisement
CONTENTS
1.
Installation ........................................................................ 1
1.1.
Technical data ......................................................... 2
1.2.
Floor Protector ........................................................ 2
1.3.
Positioning the heater ............................................. 2
1.4.
Installing the flue ..................................................... 3
1.5.
Assembly prior to installation.................................. 3
1.6.
Prior to installation - Jøtul F 305 with legs .............. 3
1.7.
Prior to installation - Jøtul F 305 with base ............. 4
1.8.
Fitting the flue pipe ................................................. 4
1.9.
Fitting the baffle ...................................................... 4
1.10.
Fitting the log retainer ............................................. 5
1.11.
Performance check .................................................. 5
2.
Operating .......................................................................... 6
2.1.
Safety ....................................................................... 6
2.2.
Using the fireplace for the first time ....................... 6
2.3.
Wood quality ........................................................... 6
2.4.
Initial lighting ........................................................... 7
2.5.
Adding firewood ...................................................... 7
2.6.
Danger of overheating ............................................. 7
2.7.
Ash removal ............................................................. 7
2.8.
Stacking wood ......................................................... 7
3.
Maintenance ..................................................................... 8
3.1.
Cleaning the glass .................................................... 8
3.2.
Cleaning and soot removal ...................................... 8
3.3.
Cleaning the Flue ..................................................... 8
3.4.
Inspection of the fireplace ....................................... 8
3.5.
Exterior maintenance .............................................. 8
4.
Servicing ............................................................................ 9
4.1.
Replacing parts in the burn chamber ...................... 9
4.2.
Dismounting the door ............................................. 9
4.3.
Replacing glass and gaskets in the door .................. 9
4.4.
Adjusting the door ................................................. 11
5.
Troubleshooting .............................................................. 11
5.1.
Poor draught.......................................................... 11
5.2.
The fire extinguishes after a while ........................ 11
5.3.
Unusual amount of soot on glass .......................... 11
6.
Manufacturer/Distributor ............................................... 11
7.
Dimensions...................................................................... 12
1. Installation
THE INSTALLATION INSTRUCTIONS IN THIS MANUAL
APPLY TO THE JØTUL F305 WOOD HEATER MODEL.
IT HAS BEEN TESTED FOR EMISSIONS AND EFFICIENCY
AND COMPLY ACCORDING TO AS/NZS 4012:2014 &
AS/NZS 4013:2014.
Most building regulatory authorities in Australia require any
wood heater installation to comply with Installation Standard
AS/NZS 2918. Different states and councils may have varying
regulations. Check local building regulations before installing
the appliance.
All Jøtul wood heaters have been tested to ensure they will
meet the appropriate safety standard requirements if the
instructions in this manual are followed. As the safety and
emissions performance can be affected by altering the
appliance, no modifications are allowed without written
permission from the manufacturer.
WE RECOMMEND THAT THE INSTALLATION OF YOUR JØTUL
WOOD HEATER BE CARRIED OUT BY A QUALIFIED INSTALLER.
WARNING: THE APPLIANCE AND FLUE-SYSTEM SHALL BE
INSTALLED IN ACCORDANCE WITH AS/NZS 2918 AND THE
APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING
CODE OR CODES.
WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH
THIS STANDARD SHALL COMPLY WITH THE REQUIREMENTS
OF AS/NZS 4013 WHERE REQUIRED BY THE REGULATORY
AUTHORITY, I.E. THE APPLIANCE SHALL BE IDENTIFIABLE BY A
COMPLIANCE PLATE WITH THE MARKING 'TESTED TO AS/NZS
4013'.
ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN
APPROVED IN WRITING BY THE TESTING AUTHORITY IS
CONSIDERED TO BE IN BREACH OF THE APPROVAL GRANTED
FOR COMPLIANCE WITH AS/NZS 4013.
CAUTION: MIXING OF APPLIANCE OR FLUE-SYSTEM
COMPONENTS FROM DIFFERENT SOURCES OR MODIFYING
THE DIMENSIONAL SPECIFICATION OF COMPONENTS MAY
RESULT IN HAZARDOUS CONDITIONS. WHERE SUCH ACTION IS
CONSIDERED, THE MANUFACTURER SHOULD BE CONSULTED
IN THE FIRST INSTANCE.
CAUTION: CRACKED AND BROKEN COMPONENTS, e.g. GLASS
PANELS OR CERAMIC TILES, MAY RENDER THE INSTALLATION
UNSAFE.
1
Advertisement
Table of Contents
