Table of Contents
Advertisement
a,
a,
.....
N
r--
N
.....
0
0
0:
co
Programming the buttons (version B)
Appl ies to: vehicles with garage door opener (Homelink)
Fig. 44 Dist ance between the radiat or grill e and t he hand
tra nsmi tt er
Programming the button: Part 1 with the
controls
1.
Switch the ignition o n.
2 . Press and ho ld both outer buttons in the roof
headliner
c::>
page 46, fig. 43
unti l the LED@
turns off completely (after about 20 sec-
onds). This procedure clears the standard co-
des that were set at the factory and does
not
need to be repeated aga in to program the
other buttons .
3 . Briefly press t he button on the roof headline r
th at you wou ld like to prog ram.
4 . Wait un t il the LE D@ begi ns t o blink quick ly.
Programm ing mode is act ive for 5 minutes .
5 . Move in front of yo ur vehicle while holding
the orig inal remote contro l for the system
that would like to program to a button in the
roof headliner.
Programming the button : Part 2 at the
radiator grille
6 . Hold the remote control up to the radiator
grille on your vehicle ¢
fig.
44.
7 . Press and ho ld the remote control until t he
turn signals on your vehicle blink. This may
tak e up to 30 seconds .
8 . If t he emergen cy flashers blink th ree ti mes,
the progr amming wa s suc cessful. If t he
emergency flas hers only blink one t ime, t he
5 minute time limit for t he programm ing has
ended or the programm ing was not success-
ful. Repeat the programming from the third
step, or try changing the distance to the radi-
ator grille.
Open ing and closing
9 . If t he garage door or ot her syst em does not
open using the buttons in the roof head liner
even tho ugh the programming was success-
ful, the system may use a rolling code in-
stead of a fixed code.
Rolling code program-
ming
must be perfo rmed
c::>
page
48.
The other two buttons in the roof hea dli ner can
be programmed according to the inst ruct ions
above. Begin with the third step.
Erasing button programming
The programmed but t ons can not be erased indi-
vidually . They must a ll be erase d together . Re-
program the buttons if necessary .
"' Switch t he ignit ion on.
"' Press an d hold both out er but t ons in the roof
headliner until the LED@ tu rns off complete ly
(after about 20 seconds).
Reprogramming the buttons
"' Switch t he ignit ion on.
"' To reprogram an individu al but t on, press and
hold the button unti l the LED@ starts to flash
quickly (afte r about 10 seconds) . Release the
button immediate ly. Prog ramming mode is ac-
tive for 5 m inutes.
"' Continue with the fifth step.
@
Tips
- Prog ramming using the buttons in t he roof
head liner is not poss ible with a ll Infota in-
ment systems . If this is the case, p rogram
t he buttons as described in vers io n A
c::>
page 46.
- The required distance between t he hand
t ransmitte r and t he Homelink module in
t he radiat or grille ¢
fig.
44 depend s on th e
syste m t hat you ar e prog ramming.
- Depending on the mo de l of t he syst em, you
may need t o relea se th e butt on o n t he re-
mot e cont rol dur ing progra mm ing and
press it ag ain. Hold each position you try for
at least 15 seco nds befo re t rying anot her
posit ion . Keep the turn s ignals on your veh i-
cle in view whe n doin g this.
47
Advertisement
Table of Contents
