DeWalt DCF630 Instruction Manual page 31

installing attachments or accessories. An
accidental start‑up can cause injury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ chip 23 communicates with an optional
application for your smart device (such as a smart phone
or tablet) that connects the device to utilize the mobile
application for inventory management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
Installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
the screws.
4. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Collated attachment (Fig. K)
optional accessory
The DCF6202 collated drywall magazine attachment is
designed to be used with your cordless screwgun for
professional driving of collated screws.
Installing and Removing the Magazine from the
screwgun (Fig. K)
NOTICE: For proper operation only use D
collated screwdriver bit (catalog #: DCF6202PH2).
1. Remove the nose cone from the screwgun.
2. To remove the bit and bit holder:
a. Grab the bit holder.
b. Push it into the gear case depressing the sleeve.
c. Rotate the bit holder until the clutch engages.
d. While holding the sleeve depressed, pull the bit
holder out.
NoTE: Refer to and follow all instructions on changing
bits and holders in your screwgun manual.
3. Push and rotate the provided DCF6202PH2 phillips bit
for collated drywall screwgun attachment
spindle until ball lock snaps in groove of the bit shank.
4. With the the nose cone removed and provided driver bit
installed, push the DCF6202 collated drywall screwgun
attachment 24 over the bit onto the screw driver until
the magazine clicks into place and ensure that it does
not disengage.
NoTE: Make sure the forward/reverse control button is set to
forward rotation before use.
5. Refer to DCF6202 Collated Magazine Attachment
Instruction Sheet for further instructions.
Belt Hook (Fig. I)

WARNING: To reduce the risk of serious personal
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
21 that hold the Tool
22 into the tool.
.
23
WALT
e
into the
25
tool from a work belt. DO NOT use the belt hook
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or suspend
objects from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.
IMpoRTaNT: When attaching or replacing the belt hook
, use only the screw that is provided. Be sure to securely
tighten the screw.
The belt hook can be be attached to either side of the
11
tool using only the screw provided, to accommodate left‑ or
right‑ handed users. If the hook is not desired at all, it can be
removed from the tool.
To move belt hook, remove the screw that holds it in place
then reassemble on the opposite side. Be sure to securely
tighten the screw.
Nosecone Maintenance (Fig. A)
If the nose cone becomes hard to turn it may be
4
contaminated with drywall dust.
1. Remove nose cone from tool.
2. Rinse thoroughly with warm water while rotating both
screw depth adjustment collar
Never use oil or solvents.
3. Dry the nosecone completely before reattaching to tool.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement) should be performed
WALT factory service center or a DEWalT
by a D
e
authorized service center. Always use identical
replacement parts.
ENglIsh
11
and locking collar .
2 3
29