Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt XR Li-Ion DCF680-XE
Summary of Contents for DeWalt XR Li-Ion DCF680-XE
- Page 1 INSTRUCTION MANUAL DCF680-XE 7.2 V HEAVY-DUTY CORDLESS SCREWDRIVER...
-
Page 3: Definitions: Safety Guidelines
Vibration total values (triax vector sum) determined according to EN 60745: Definitions: Safety Guidelines Vibration emission value a The definitions below describe the level of severity for each signal Screwdriving without impact word. Please read the manual and pay attention to these symbols. m/s²... -
Page 4: Work Area Safety
SAVE ALL WARNINGS AND INSTRUCTIONS FOR 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when FUTURE REFERENCE operating a power tool. Do not use a power tool while you are tired or The term “power tool” in the warnings refers to your mains-operated (corded) power under the influence of drugs, alcohol or medication. -
Page 5: Extension Cords
Electrical Safety d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the The electric motor has been designed for one voltage range only. Always check that power tool. -
Page 6: Important Safety Instructions For All Battery Packs
• The label on your tool may include the following symbols. The symbols and their WARNING: ALWAYS wear approved protective safety equipment complying with definitions are as follows: the following standards: V ....volts A ......amperes • Eye protection: AS/NZS1337 Eye Protectors for Industrial Applications; Hz .... -
Page 7: Specific Safety Instructions For Lithium Ion (Li-Ion)
• DO NOT splash or immerse in water or other liquids. • Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention. • Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 40 °C (105 °F) (such as outside sheds WARNING: Burn hazard. -
Page 8: Charge Indicators
FIG. 1 Charging Procedure (Fig. 1) • Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock or 1. Plug the charger into an appropriate outlet before electrocution. -
Page 9: Important Charging Notes
c. Move the charger and battery pack to a location where the surrounding air HOT/COLD DELAY temperature is approximately 18 ° – 24 °C (65 °F and 75 °F); This charger has a hot/cold delay feature: when the charger detects a battery that is hot, it automatically starts a delay, suspending charging until the battery has cooled. - Page 10 COMPONENTS (Fig. 2) INTENDED USE This cordless screwdriver is designed for professional fastening applications. WARNING: Never modify the power tool or any part of it. Damage or personal DO NOT use under wet conditions or in presence of flammable liquids or gases. injury could result.
-
Page 11: Operation
OPERATION For more information regarding fuel gauge battery packs, please contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call 1800 338 002 or (NZ) WARNING: To reduce the risk of serious personal injury, turn the tool off and 0800 339 258. -
Page 12: Maintenance
Cleaning VARIABLE SPEED • The spindle speed is dependent upon the speed that you rotate your hand. WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once • The slower you rotate your hand, the slower the screwdriver turns. a week. - Page 16 Stanley Black & Decker 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (MAR13) Part No. 239583 DCF680-XE Copyright © 2013 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...