Advertisement
Quick Links
INSTALLATION GUIDE
HYPERSTAT
INTRODUCTION
HyperStat is a wall-mount thermostat. Its thoughtful design ensures that it blends into most
commercial spaces while still giving a fresh and contemporary feel compared to dated
building control interfaces.
PACKAGE CONTENTS
•
HyperStat device
•
Mounting accessories
SPECIFICATIONS
Power
Operating range
Communication
Onboard Sensors
Inputs
(7C-HS-C2W-X)
Power Source: 24V AC/DC input (+/- 15%)
Peak consumption: 1.4VA Maximum
Temperature 32 to 122°F (0°C to 50°C)
Humidity 20-85% non-condensing.
Sensor bus for daisy chained sensor communication and low power 3V dc.
4-wire interface for RS 485 communication @ 115200 baud and 5V
DC, 100mA power source
900-928 MHz Mesh IEEE 802.15.4-compliant, for communications to CCU
Bluetooth: BLE 4.1 for commissioning, and communication to wireless sensors
Temperature range of 32 to 122°F with an accuracy of +/-1°F
Humidity 0 to 100% with an accuracy of 2%
CO2 sensor with a range of 0 - 40,000 ppm, accuracy of +/-30ppm
VOC sensor; Typical Accuracy: 15% of measured value; TVOC: 0 - 60,000
ppb;
Occupancy sensor based on passive infrared (PIR) with a detection range of
4m with a 15-degree angle
Light Sensor. Ambient light sensor • <100 LUX resolution • High-accuracy UV
index sensor • Matches erythermal curve
Sound sensor with 40-120dB response for 100Hz to 10KHz
PM2.5, PM10 sensor (optional). Detection range of 0-1000µg/m3 and accuracy
of +/-10µg/m3 (PM2.5, 0-100µg/m3) or +/-25µg/m3 (PM10, 0-
100µg/m3). Maximum long-term mass concentration precision limit drift:
•
0 to 100 µg/m3 ±1.25 µg/m3/year
•
100 to 1000 µg/m3 ±1.25 % mV/year
2 x 10K Type-2 thermistor inputs with 2% accuracy
2 x 0-10V Analog voltage inputs with 2% detection accuracy (2-10V)
Touch slider for temperature control along with 3 mechanical buttons
For more information, contact your local Carrier Controls Expert
©2023 Carrier. All Rights Reserved. Cat. No. 11-808-959-01
Scan this QR
code to get a
more detailed
version of the
Installation
Guide
Advertisement
Related Manuals for Carrier HYPERSTAT
Summary of Contents for Carrier HYPERSTAT
- Page 1 INSTALLATION GUIDE HYPERSTAT (7C-HS-C2W-X) INTRODUCTION HyperStat is a wall-mount thermostat. Its thoughtful design ensures that it blends into most commercial spaces while still giving a fresh and contemporary feel compared to dated building control interfaces. PACKAGE CONTENTS Scan this QR...
- Page 2 • Do not assemble the front to the back plate while it is powered on. • Once Installed the HyperStat takes seven days to auto-calibrate and settles at a steady state value. • Avoid mechanical stress on the CO2 sensor to get accurate readings.
- Page 3 DIS-ASSEMBLING If the HyperStat is mounted on the wall, hold the front plastic with both hands and pull it away from the wall. If you are holding the HyperStat in your hands, insert a flat head screwdriver in the notch provided (marked by the two arrows shown in the image) between the front and back plastic and twist to separate them.
- Page 4 Scan this QR code to get a more detailed version of the Installation Guide If you need help beyond that, please reach out to your local Carrier distributor for support. Note • • Favorable for Pollution degree 2 or the equivalent Rated impulse voltage –...