Beninca BRAINY Quick Start Manual

QUICK START GUIDE
BRAINY
Full feature control panel
QUICK START GUIDE
USE THIS QUICK START GUIDE TOGETHER
BRAINY
WITH THE INSTRUCTION MANUAL PROVIDED.
Full feature control panel
F2
A
F1
GND
L N
115/230Vac
50/60Hz
1.
USE THIS QUICK START GUIDE TOGETHER
WITH THE INSTRUCTION MANUAL PROVIDED.
STAGE 1:
STAGE 1:
First stage is to correctly wire in the motors
to the panel via terminals 4, 5 & 6 for Motor
First stage is to correctly wire in the
1 and 7, 8 & 9 for Motor 2
motors to the panel via terminals A
using a single operator, ensure to just use
4, 5 & 6 for Motor 1 A and 7, 8 & 9
the motor 1 terminals 4,5, & 6 and turn for Motor 2 B . If only using a single
operator, ensure to just use the motor
to ON in the logic menu.
1 terminals 4,5, & 6 and turn Inot to
ON in the logic menu.
! !
Most of the parameters can
be pre-determined via the
Most of the parameters can be pre-
autoset feature. This can
determined via the autoset feature.
only be used when using motors
This can only be used when using
equipped with encoders.
motors equipped with encoders.
If installing motors without
If installing motors without encoders
encoders then set up of the panel
then set up of the panel must be
must be completed manually. To
completed manually. To do this, you
do this, you must ensure that the
must ensure that the LOGIC setting
LOGIC setting Enc is turned OFF.
ENC is turned OFF.
UNITED
KINGDOM
QUICK START GUIDE
BRAINY
Full feature control panel
F2
AUX 2
J2 DAS
Close
DAS 8K2
J2 DAS
Open
AUX 1 DAS N.C.
B
A
F1
GND
L N
115/230Vac
50/60Hz
USE THIS QUICK START GUIDE TOGETHER
NAVIGATING THE PANEL
WITH THE INSTRUCTION MANUAL PROVIDED.
BUTTONS:
+ Navigate up / Increase value
NAVIGATING THE PANEL
STAGE 1:
OK Enter / Select / Confirm
BUTTONS:
First stage is to correctly wire in the motors
-
to the panel via terminals 4, 5 & 6 for Motor
. If only +
B
1 and 7, 8 & 9 for Motor 2
A
OK Enter / Select / Confirm
using a single operator, ensure to just use
-
the motor 1 terminals 4,5, & 6 and turn
UNDERSTANDING
to ON in the logic menu.
THE BASIC MENUS
UNDERSTANDING PARAMETERS ( PAr ) All settings
THE BASIC MENUS
with numerical values that can be
altered. Time, force, percentages.
PARAMETERS
Most of the parameters can be pre-
LOGIC ( LOG ) All settings that can
numerical values that can be altered.
determined via the autoset feature.
be turned on or off.
Time, force, percentages.
This can only be used when using
RADIO ( RAD ) All settings relating to
LOGIC
motors equipped with encoders.
adding or removing transmitters.
turned on or off.
If installing motors without encoders
Autoset ( AUto ) Self calibration
RADIO
then set up of the panel must be
setting of encoded motors.
adding or removing transmitters.
completed manually. To do this, you
Autoset (
must ensure that the LOGIC setting
of encoded motors.
ENC is turned OFF.
STOP
PHOT (Close)
PHOT
CLOSE
OPEN
PED.
AUX 2
P.P.
COM
COM
SWC-M2 (Close)
SWO-M2 (Open)
J2 DAS
Close
SWC-M1 (Close)
DAS 8K2
SWO-M1 (Open)
J2 DAS
Open
AUX 1 DAS N.C.
B
+ Brown
S Green
- White
Navigate down / Decrease
Navigate up / Increase value
value / Trigger
. If only
B
Navigate down / Decrease value /
Trigger
( )
PAr
All settings with
( )
LOG
All settings that can be
( )
RAD
All settings relating to
Auto
Self calibration setting
)
01488 658 276
Beninca Automation UK Ltd
info@beninca.co.uk
Unit 4, Plenty Close,
Newbury, Berkshire, RG14 5RL
beninca.co.uk
STOP
PHOT (Close)
PHOT
CLOSE
OPEN
PED.
P.P.
COM
COM
SWC-M2 (Close)
SWO-M2 (Open)
SWC-M1 (Close)
SWO-M1 (Open)
2.
STAGE 2:
STAGE 2:
NAVIGATING THE PANEL Power up the control. At this point, you
should have only the motors wired in.
Power up the control. At this point,
BUTTONS:
you should have only the motors
Press the < - > button to trigger the gates.
+ Navigate up / Increase value
wired in.
Both gates should attempt to open. If
OK Enter / Select / Confirm
Press the < - > button to trigger the
either begins to close upon triggering you
- Navigate down / Decrease value / gates. Both gates should attempt to
will need to reverse the phases of that
open. If either begins to close upon
Trigger
particular motor.
triggering you will need to reverse the
Note; the DL4 light will constantly flash.
phases of that particular motor.
UNDERSTANDING
This is perfectly normal.
THE BASIC MENUS Note; the DL4 light will constantly
flash. This is perfectly normal.
( )
PAr
All settings with
PARAMETERS
numerical values that can be altered.
Time, force, percentages.
( )
LOG
All settings that can be
LOGIC
turned on or off.
( )
RAD
All settings relating to
RADIO
adding or removing transmitters.
Auto
Self calibration setting
Autoset ( )
of encoded motors.
beninca.co.uk
Beninca Automation UK Ltd
01488 658 276
Unit 4, Plenty Close,
info@beninca.co.uk
Newbury, Berkshire, RG14 5RL
+ Brown
S Green
- White
STAGE 2:
Power up the contr
should have only t
Press the < - > butt
Both gates should a
either begins to clo
will need to reverse
particular motor.
Note; the DL4 light
This is perfectly nor