Table of Contents
Advertisement
Quick Links
Instructions
Air Control Solenoid Valve
for Fluid Defender
For regulating air powered equipment connected to the Fluid Defender. For professional
use only.
Not approved for use in explosive atmospheres or hazardous (classified) locations.
Models:
25V482 - Kit, Solenoid, Air, Pump
145 psi (1.0 MPa, 10 bar) Maximum Working Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual before using the equipment.
Save these instructions.
Related Manuals
Manual in
Description
English
®
Pulse
Fluid Management, Register Your
130641
Devices quick guide
3A9335
Fluid Defender
3A7279
Fluid Defender Level Sensor
™
3A7280A
EN
Advertisement
Table of Contents
Related Manuals for Graco 25V482
Summary of Contents for Graco 25V482
- Page 1 For regulating air powered equipment connected to the Fluid Defender. For professional use only. Not approved for use in explosive atmospheres or hazardous (classified) locations. Models: 25V482 - Kit, Solenoid, Air, Pump 145 psi (1.0 MPa, 10 bar) Maximum Working Pressure Important Safety Instructions Read all warnings and instructions in this manual before using the equipment.
- Page 2 Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
-
Page 3: Typical Installation
. 3 are the three targeted applications for the Fluid Defender. Each typical installation shown is configurable as a single separate channel. Follow all local codes and regulations for tank installations. Consult your local Graco representative or distributor for system design assistance. - Page 4 Typical Installation Fresh Oil Low Level 3A7280A...
- Page 5 Typical Installation Remote Bulk Fill Stop 3A7280A...
- Page 6 Overview Overview Air Control Solenoid Valves Air control solenoid valves are a Fluid Defender system component used to control air operated pumps and air actuated control valves. These devices are used to stop fluid flow into the monitored tank. They are an optional system component, but required for fluid flow interruption.
-
Page 7: Installation
Installation Installation 2. Turn the Fluid Defender keyed power control off to de-energize the connected air control solenoid valves. OMPONENT UPTURE AZARD 3. Follow the pressure relief procedure for all connected equipment, such as pumps and The air actuated control valve, and all of the fill piping dispense valves from your component instruction and connections between the air actuated control manuals. - Page 8 Installation 5. Attach all accessory wires to the Fluid Defender control box following all local codes and regulations. Reference the Technical Specifications, page 13, for information on maximum wire runs. All accessory circuits are low voltage (less than 48 VDC). 3A7280A...
-
Page 9: Operation
Only use manual override for system setup, or when manual override switch screw counterclockwise instructed by Graco for troubleshooting. Always set the back to the original position (F . 6). mode of operation back to the normal operating position. -
Page 10: Recycling And Disposal
Recycling and Disposal Recycling and Disposal Troubleshooting End of Product Life At the end of a product’s useful life, recycle it in a responsible manner. Follow the pressure relief instructions in your pump manual, before checking or repairing the system. See Fluid Defender manual, Related Manuals, page 1 for Troubleshooting information. - Page 11 Part No. 25V482 Part No. 24Z670 3A7280A...
- Page 12 Dimensions Dimensions 3A7280A...
-
Page 13: Technical Specifications
Technical Specifications Technical Specifications Air Control Solenoid Valve for Fluid Defender Metric Minimum Operating Pressure 36 psi 250 kPa, 2.5 bar Maximum Operating Pressure 145 psi 1.0 MPa, 10 bar 93 scfm Maximum Air Flow 2.6 m /min. Operating Power 3.3 W Voltage 24 VDC... -
Page 14: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.