Advertisement
Neyiess ^nucK uperanon
Catalog Numbers CD231, CD431, HP131, HP231, HP331,HP431, FS432, FS632, FS840 -Two Sleeve
Chucks - To attach accessories, grasp the rear half of the chuck with one hand and use your other hand to
rotate the front half In the counterclockwise direction. Insert the bit or other occesso^ fully into the chuck, and
tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction
OS viewed from the chuck end.
Catalog Numbers CD632, HP532, HP932, FS1320- Single Sleeve Chuck with Automatic Spindle Lock -
Loosen the chuck by rotating the sleeve counterclockwise. Insert the bit or other accessory fully into the chuck,
and tighten securely by rotating the front portion In the clockwise direction as viewed from the chuck end.
Drilling
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the Safety Instructions.
• Use appropriate and required safely equipment, as instructed in the safely instructions.
• Secure and maintain work area, as instructed In the safely Instructions.
• Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from
slipping out of It.
• Apply pressure In a straight line with the bit. Use enough pressure to keep the bit biting but not so
much as to stall the motor or deflect the bit.
• Hold the drill firmly to control its twisting action.
• DO NOT CUCK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN AHEMPT TO START IT.
DAMAGE TO THE DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure and slowly drilling through lost part of hol^,
• Keep the motor running while pulling the bit out of a drilled hole This will help reduce jamming.
• Use a cutting lubricant when drilling metals. The exceptions ore cost iron and brass which should be
drilled dry. Lubricants that work best are sulphurized cutting oil or lard oil.
• When using twist drill bits to drill holes in wood. It will be necessary to pull the bits out frequently to
clear chips from the flutes.
•
Make sure swtch turns drill on and off.
A WARNING: It is important to support work properly and to hold the drill firmly to prevent loss of control
which could cause personal injury if you have quesfions on how to operate tool, coll: 1-800'54-HOW-TO
Maintenance
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never Immerse
any port of the tool into a liquid. IMPORTANT: To assure product SAFETY and REUABIUTY, repairs,
maintenance and adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement ports.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corparation)Seal on the nickel-cadmium bottery
(or battery pock) indicates that the costs to recycle the battery (or battery pack) at the end of Its
useful life have already been paid by Black & Decker. In some areas, it Is illegal to place spent
nickel-cadmium batteries in the trash or municipal solid waste stream and the RBRC program
provides an environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established programs in the United
States and Canada to facilitate the collection of spent nlckel-codmlum batteries. Help protect our environment
and conserve natural resources by returning the spent nickel-cadmium battery to an authorized Black &
Decker service center or to your local retailer for recycling. You may also contact your local recycling center
for information on where to drop off the spent battery, or call T -800-8-BATTERY.
Accessories
Recommended accessories for use with your tool ore avalloble from your local dealer or authorized service
center. If you need assistance regarding accessories, please call: 1-800-54-HOW-TO. The following
accessaries should be used only in the sizes specified below: BITS, METAL DRILLING - Up to 3/8" (9.5mm);
BITS, MASONRY DRILUNG - Up to 3/8" (9.5mm); WOOD DRILUNG - Up to 1 /2" (12.7mm).
AwARNING: The use of any accessory not recommended for use with this tool could be hazardous.
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against onv defects in material or
workmanship. The defective product will be replaced or repaired at no chorge in either of two ways. The first,
which will result In exchanges only. Is to return the product to the retailer from svhom It was purchased
(provided that the store is a participating retailer). Returns should be mode within the time period of the
retailer's policy for exchanges (usuolly 30 to 90 days after the sale). Proof of purchase may be required.
Please check with the retailer for their specific return policy regarding returns that are beyond the time set for
exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service
Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned
and authorized service centers are listed under "Tools-Electric" In the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have
other rights which vary from state to state. Should you have any questions, contact the manager of your
nearest Black & Decker Service Center. This product is not intend^ for commercial use.
SPECIAL WARRANTY NOTE TO CONTRAQORS:
FIRESTORM^'^ bronded products ore offered as high end CONSUMER home use tools and carry a HOME
USE WARRANTY. These fools ore designed, manufactured and tested to meet or exceed the needs of the do-
ihyourselfer in the execution of projects and repairs in and around the home. With proper use they will
prowde the home owner with step up power and performance well beyond flieir two year warranty.
However, if you use fools for a living and use FIRESTORM™ branded products or any of Black & Decker's
other Consumer Home Use tools ON THE JOBSITE you should know that they CANNOT BE COVERED
UNDER OUR WARRANTY.
I YOUTfEGOTTHETOOL |
Imported by
(1-80D-54-HOW-TD
Black & Cwker (U.S.) Inc.,
^ ' * — « ' '
701 E. Jop^ Rd.
[ltttpV/gra.blacbii(ldecter.coBj
- Yellow Pages -
Towson, MD 21286 U.S.A.
i^iowEgnraraofrHOwJ
Service & Sates
Advertisement
