Beyerdynamic MMX 100 - Gaming Headset Manual

Also See for MMX 100:

Table of Contents

SUPPLIED ACCESSORIES

1 x 5-pole jack to 4-pole jack cable, 1.2 m (3.9 ft), to connect the headset to mobile devices
1 x 5-pole jack to 2 x 3-pole jack cable, 2 m (6.5 ft), to connect the headset to a computer or console
1 x Microphone pop shield

Accessories and replacement equipment can be found at: www.beyerdynamic.com
If you have technical questions while using the headset or need further guidance, please visit our FAQ website at:
support.beyerdynamic.com

Use a soft cloth moistened with water to clean the surface.
Make sure that no water enters the headset.
Do not use cleaning agents containing solvents.
Never use a vacuum cleaner for cleaning the headset, as this may cause irreparable damage.

Observe the position of the jack.

Connect the jack connector to the headset.
Connect the cable to the headset - Step 1

Pull the connection carefully to disconnect, if you want to use another cable.
Connect the cable to the headset - Step 2

Connect the flat 5-pole jack to the headset and the round 4-pole jack to your device such as console controllers, external soundcards, notebooks, tablets etc.
For devices with 1/4" jack (6.35 mm), please use a third party adapter. Make sure that it is a 4-pole adapter, as the microphone will not work with a 3-pole 1/4" (6.35 mm) TRS adapter.
Connect the round 4-pole jack connector of the cable to a headphone socket only!
If you connect the headset to any other jack socket, the headset could be damaged.

Connect the flat 5-pole jack to the headset and the two round 3-pole jack connectors to a headphone output and microphone input of a PC or notebook, which have a mini combination jack (3.5 mm).
For devices with 1/4" jack (6.35 mm), please use one of ours or a third-party adapter.
Connect the round 3-pole jack connectors of the cable to a headphone and microphone socket only!
If you connect the headset to any other jack sockets, the headset could be damaged.

To attach the ear pad, place it on to the orange housing and gently turn it clockwise until it sits tight.

Headphone
Transducer type		Dynamic
Operating principle		Closed
Sound coupling to the ear		Circumaural
Frequency response		5 - 30,000 Hz
Impedance		32 Ω
Max. sound pressure level @1 mW / 500 Hz		116 dB SPL
T.H.D.		< 0.5%
Headband pressure		4.5 N
Connection		5-pole mini jack plug (3.5 mm)
Weight (headphone)		296 g (10.44 oz)
Microphone
Transducer type		Electret condenser
Capsule diameter		9.9 mm (0.39")
Polar pattern		Cardioid
Frequency response		5 - 18,000 Hz
Max. sound pressure level		118 dB
Signal-to-noise ratio		67 dB

Risk of injury

We would like to point out that excessively high volumes and long listening times may cause hearing damage. Hearing defects always constitute an irreversible impairment of hearing ability. If you suffer from tinnitus, do not use headphones or reduce the volume.
When connecting the headset, please ensure that the volume is turned down to minimum. Adjust the volume after putting on the headset.

warning
Danger to life

Headphones drastically reduce perception of external sounds. Using headphones in road traffic can be potentially dangerous. The user's hearing must not be impaired to the extent that it causes road safety risks. Please also make sure that you do not use the headphones in traffic, especially within an area of potentially dangerous machines and tools.
Furthermore, avoid using headphones in situations where hearing must not be affected, especially when crossing a railway crossing or at a construction site.

Liability / intended use

Do not use the product for any application which is not described in this product information.
beyerdynamic is not liable for improper use of the product and its accessories.

If you require service, please contact qualified service personnel or directly:
beyerdynamic Service- und Logistik Center
E-mail: service@beyerdynamic.de
Dismantling the headset yourself will invalidate the guarantee.