Related Manuals for Dahua EW5541-AS
Summary of Contents for Dahua EW5541-AS
- Page 1 IR Fisheye Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.2...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, WARNING could result in slight or moderate injury. - Page 3 Quick Start Guide All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners. Please visit our website, contact the supplier or customer service if there is any problem occurred when using the device. If there is any uncertainty or controversy, please refer to our final explanation.
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings Electrical Safety All installation and operation shall conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited Power Source requirement according to IEC60950-1. Note that the power supply requirement is subject to the device label. - Page 5 Quick Start Guide It is recommended to ground the device to enhance reliability. Do not touch the image sensor (CMOS) directly. Dust and dirt can be removed with air blower, or you can wipe the lens gently with soft cloth that is moistened with alcohol. You can clean the device body with soft dry cloth, and for stubborn stains, use the cloth with mild ...
-
Page 6: Table Of Contents
Quick Start Guide Table of Contents Foreword ................................I Important Safeguards and Warnings ......................III 1 Introduction ..............................1 General ......................................1 Device Ports ....................................1 Connecting Alarm Input/output ............................2 2 Network Configuration ..........................4 Initializing Device ..................................4 Modifying Device IP Address .............................. -
Page 7: Introduction
Quick Start Guide Introduction General This series of digital video cameras use internet protocol, and they can send and receive audio and video data through network independently. They are equipped with fisheye lens and advanced algorithm of fisheye image rectification; they support surveillance with no dead zone and panorama image output with multiple image screens, and every screen supports virtual PTZ. -
Page 8: Connecting Alarm Input/Output
Quick Start Guide Table 1-2 Alarm I/O port information Port Port Name Function ALARM_OUT Outputs alarm signal to alarm device. Alarm I/O ALARM_IN Receives the switch signal of external alarm source. ALARM_GND Ground connection. Connecting Alarm Input/output Alarm input/output is available on select models. Connect alarm input device to the alarm input end of the I/O port. - Page 9 Quick Start Guide Mode B Log in to web interface, and configure alarm input and alarm output in alarm setting. The alarm input on the web interface is corresponding to the alarm input end of the I/O port. There will be high level and low level alarm signal generated by the alarm input device when alarm occurs, set the input mode to "NO"...
-
Page 10: Network Configuration
Quick Start Guide Network Configuration Device initialization and IP address setting can be finished with the "ConfigTool" or on web interface. Web Operation Manual For more information, see the Device initialization is available on select models, and it is required at first use or after the device ... -
Page 11: Modifying Device Ip Address
Quick Start Guide Select the devices that need initialization, and then click Initialize. The password setting interface is displayed. See Figure 2-2. Password setting Set and confirm the password of the devices, then enter a valid email address, and then click Next. -
Page 12: Logging In To Web Interface
Quick Start Guide Modify IP Address Select Static mode, and then enter start IP, subnet mask, and gateway. IP addresses of multiple devices will be set to the same if you select the Same IP check box. If DHCP server is available in the network, devices will automatically obtain IP addresses ... -
Page 13: Installation
Quick Start Guide Installation Packing List The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool information are contained in the disk or the QR code, and ... -
Page 14: Installing Device
Quick Start Guide Installing Device 3.3.1 Installation Type 3.3.2 Installing SD Card (Optional) Disconnect the power before installing or removing the SD card. -
Page 15: Attaching Device
Quick Start Guide Press the WPS button on your router, and then press and hold the WPS button on the camera for 1-2 s, the camera would be connected to your router within 1 min. Press and hold the WPS button on the camera for at least 10 s during proper operation state, and ... - Page 16 Quick Start Guide Mounting plate Positioning map Locking Mounting Plate The mounting plate is at the "open" state by default, make sure it stays "open" when installing the camera; and adjust it to the "close" state after installation. When the mounting plate is at the "open" state, you can install, adjust, or remove the camera; and ...
- Page 17 Quick Start Guide Fixing Device Cable going through the mounting surface...
- Page 18 Quick Start Guide Cable going through the side cable tray...
- Page 19 Quick Start Guide...