Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dahua A
Summary of Contents for Dahua A
- Page 1 HDCVI Camera User’s Manual Version 1.0.0...
-
Page 2: Table Of Contents
General Introduction ........................1 Overview ..........................1 Features..........................1 Device Framework .......................... 2 Installation ............................5 Model A ............................5 Model B1 and B2..........................6 Model C ............................7 Model D ............................8 Model E ............................9 Model F............................10 Menu .............................. -
Page 3: Important Safeguards And Warnings
Welcome Thank you for purchasing our HDCVI camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference! Important Safeguards and Warnings 1. - Page 4 damage to the device. Any device is not supported to be connected between the camera and PoC XVR when the camera is in the condition of PoC power supply, including UTC, Balun, optical transceiver, distributor and convertor etc. Otherwise it may burn the connected device. ...
-
Page 5: General Introduction
1 General Introduction 1.1 Overview This series HDCVI camera conforms to the HDCVI standard. It supports video signal high- speed long distance transmission without any delay. It can be controlled by the HCVR conforming to the HDCVI. 1.2 Features High-performance CMOS image sensor, megapixel definition. -
Page 6: Device Framework
2 Device Framework See Figure 2-1 for the dimension of model A. Figure 2-1 See Figure 2-2 and Figure 2-3 for the dimension of model B1 and model B2. Figure 2-2 Figure 2-3... -
Page 7: Figure
See Figure 2-4 for the dimension of model C. Figure 2-4 See Figure 2-5 for the dimension of model D. Figure 2-5 See Figure 2-6 for the dimension of model E. Figure 2-6 See Figure 2-7 for the dimension of model F. - Page 8 Figure 2-7 The device ports include one DC12V power input port and one BNC video output port. Please refer to Figure 2-8 for DC12V power input port. Figure 2-8 Please refer to Figure 2-9 for video output port. Figure 2-9 Note ...
-
Page 9: Installation
Step 5 Rotate the decoration ring and fix it slightly, rotate the enclosure and dome body to a proper monitoring location; connect the video output port of device cable to back-end encoding device, and connect power port to power;... -
Page 10: Model B1 And B2
Focus end. 3. It needs to select a proper slotted screwdriver when adjusting Zoom and Focus. It is recommended that the size of screwdriver head should be 3.5*0.7mm (width*depth). -
Page 11: Model C
Step 5 Put the enclosure and dome body into the pedestal, insert locking screws clockwise and fix them slightly; rotate enclosure and dome body to a proper monitoring location; finally fasten the locking screws firmly. So far the device installation and cable connection are completed; you can check the monitoring image via back-end coding device. -
Page 12: Model D
Step 5 Rotate the decoration ring and fix it slightly, rotate the compression cover and dome body to a proper monitoring location; finally rotate the decoration ring firmly. -
Page 13: Model E
Step 5 Make the enclosure buckle get stuck into the pedestal, rotate the enclosure and dome body to a proper monitoring location. So far the device installation and cable connection are completed; you can check the image via back-end coding device. -
Page 14: Model F
Step 5 Put the enclosure and dome body into the pedestal, insert locking screws clockwise and fix them slightly; rotate enclosure and dome body to a proper monitoring location; finally fasten the locking screws firmly. So far the device installation and cable connection are completed; you can check the monitoring image via back-end coding device. - Page 15 Figure 3-7 Step 1 Use expansion bolts to fix the pedestal on the mounting surface. Step 2 Align the dome body with the location of U-shaped groove, and lay the dome body into the enclosure; buckle the enclosure on the device pedestal. Step 3 Install the rotation ring after the enclosure is fixed on the pedestal together with the dome body;...
-
Page 16: Menu
4 Menu 4.1 HCVR Settings This HDCVI camera series can adjust OSD menu via coaxial control. After connected the camera to the HDCVI series HCVR, from Main Menu->Setting->System->PTZ, you need to select the channel number for access and set control mode as HDCVI and the protocol as HD- CVI. -
Page 17: Set Audio Coax
Figure 4-3 See Sheet 4-1 for the details of button functions. Button Function Open menu 、 Select menu item Select menu value 、 Sheet 4-1 4.3 Set Audio Coax From “Main Menu > Setting > Camera > Encode > Encode”, you need to set “Audio Format” as “G711a”... - Page 18 Figure 4-4 If there is “ ”, click the “Confirm” button in “Menu Operation” interface to go to the 2nd menu. Click “Return” button to go back to the previous menu interface. Please use an UTC controller or enter the OSD menu for to switchover between HD & SD video output.
Need help?
Do you have a question about the A and is the answer not in the manual?
Questions and answers