Please check the status and power of the lithium battery upon receipt. promptly. If there are any quality issues, please contact Godox or our authorized Dot not use damaged equipment or accessories. Allow professional repair dealer within the warranty period.
TTL/M Mode Switch Function 16. Battery Compartment Screen Lock 17. Battery Remove Button 18. Sync Cord Jack Mode Lock 19. USB-C Upgrading Port The Reason & Solution of Not Triggering in Godox Control Panel 2.4G Wireless Other Applications Sync Triggering Modeling Flash ⑥...
Detachable Sub Flash SU-1 Radio Transmission Shooting: Transmitter Unit (2.4G Wireless Transmitting) ② ① ⑦ ③ ① ⑧ ⑨ ④ 1. Flash Tube ② ⑩ 2. Detaching Pusher ⑤ LCD Panel ⑥ i-TTL Auto Flash 1. Radio Transmission Shooting 6. Group C: Receiver Unit Group C 2.
Battery Then rotate it to the right until it locks Detaching battery: Installing battery: Detaching the camera flash: Press and rotate the hot shoe fixing Press and hold the battery remove Insert the battery into the battery buckle to the left until it is loosened, button, then push the battery out compartment in the direction then take off the camera flash.
Flash Mode — i-TTL Auto Flash 1. Set the flash sync speed to 1/320s (auto FP) or 1/250s (auto FP) in Nikon camera setting. Half press the shutter button and < > will be displayed on In i-TTL mode, the camera's metering system detects the flash reflected the LCD panel.
S2 Optic Control Unit Setting Note: 1. Multi flash is most effective with a highly reflective subject against a dark background. In M manual flash mode, press <S1/S2> button so that this flash can also 2. Using a tripod and TTL flash trigger XPROII is recommended. function as an optic S2 secondary flash with optic sensor.
Positioning and Operation Range (Example of wireless flash Wireless Settings shooting) You can switch between normal flash and wireless flash. For normal flash shooting, be sure to set the wireless setting to “OFF”, and the < > won’t be displayed on the LCD panel. Auto Flash Shooting with One Receiver Unit Setting the Flash as A Transmitter Unit Press <...
ID Settings 2. Receiver Unit Setting Press the wireless button and the Change the wireless channels and wireless ID to avoid interference for it can <RX> is displayed on the LCD panel, only be triggered after the wireless channels and IDs of the transmitter unit then the V1Pro S wirelessly controlled and the receiver unit are set to the same.
Using Automatic Wireless Flash with Multiple Receiver Units 2. Set the Flash Output of Each Flash Group Press function button <M/A/B/C > When stronger flash output or more to choose a group. Turn the select convenient lighting operation is needed, dial to set the flash output of the increase the number of receiver units group, then press the set button to...
This can soften shadows The Reason & Solution of Not Triggering in Godox behind the subject for a more 2.4G Wireless natural-looking shot. This is called bounce flash.
C.Fn: Setting Custom Functions Number of flashes that will activate over-temperature protection: Press the menu button to enter C.Fn settings. Power Output Level Number of Flashes Custom Function Signs Function Options Settings & Description 1/2 (+0.1~+0.9) m/ft Distance indicator 1/4(+0.1~+0.9) Feet 1/8(+0.1~+0.9) AF-assist beam...
USB-C cable (sold separately). Recycle Time Approx. 1.3 seconds. Green LED indicator will light 2. As the firmware upgrade needs the support of Godox G3 software, please up when the flash is ready. download and install the "Godox G3 firmware upgrade software" before Number of Flashes at 1/1 Approx.
Page 14
Maximum EIRP Power: -10.82dBm 品使用过程中正常的脱色,磨损和消耗,不是保修范围内的故障。 Declaration of Conformity GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in 产品保修 compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this 产品的保修期和服务类型按以下《产品保修信息》执行:...
Page 15
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot...
Need help?
Do you have a question about the V1 N PRO and is the answer not in the manual?
Questions and answers