Advertisement
Quick Links
Assembly Instructions
Model:
Description:
Part Number:
Assembly Time:
Before you beign, read thought these instructions and check that
all parts are present. Please note that MB Quart cannot assume any
responsibility for damage resulting from incorrect installation.
No.
1
6.5in Midbass Speaker Kit (JW1-116E)
2
6.5in Lower Dash Speaker Enclosure (JE1-116)
3
3.5in Coaxial Speakers (JC1-108)
4
6x9in Rear Coaxial Kit (JC1-169SB)
5
Speaker Harness
1
Bojo or Panel Tool
2
Philips Screwdriver
3
8, 10, 13mm Socket
4
Rachet
Jeep JL (Wrangler) & JT (Gladiator)
Front, Rear, Top Dash Speaker Install
MBQJ-STG6-1
120 Min (2-Hours)
Parts List
Component Name
Tools Required
Page 1 of 33
Parts List
Qty
2
2
2
2
2
Advertisement
Related Manuals for MB QUART MBQJ-STG6-1
Summary of Contents for MB QUART MBQJ-STG6-1
- Page 1 Part Number: 120 Min (2-Hours) Assembly Time: Before you beign, read thought these instructions and check that all parts are present. Please note that MB Quart cannot assume any responsibility for damage resulting from incorrect installation. Parts List Parts List Component Name 6.5in Midbass Speaker Kit (JW1-116E)
- Page 2 Dash Disassembly ● Unclip and remove panel below the steering column ● Remove (2) Phillips screws ● Unclip, unplug, and remove the climate control panel Page 2 of 33...
- Page 3 Dash Disassembly ● Remove (2) Phillips screws securing the radio trim panel, then unclip and remove ● Remove (1) Phillips screw securing the front dash pad, carefully unclip and remove by pulling forward toward the front seats Page 3 of 33...
- Page 4 Dash Disassembly ● Carefully unclip the instrument panel shroud along the bottom and remove ● Unclip the lower steering column shroud and move toward steering wheel Page 4 of 33...
- Page 5 Dash Disassembly ● Unclip and remove the panel on the side of the dash ● Remove (5) Phillips screws that are exposed ● Unclip kick panel cover Page 5 of 33...
- Page 6 Dash Disassembly ● Remove (1) Phillips screw from lower left dash ● Remove (2) Phillips screws near steering column ● Remove (2) Phillips screws on the top of the left dash then unclip and disconnect wiring on back of light switch to remove panel from vehicle Page 6 of 33...
- Page 7 Lower Speaker Removal ● Remove (4) 10mm bolts below steering column. (one is hidden behind the cross brace behind the left down support) ● Remove (1) 8mm bolt below the speaker and this will free the lower support brace to aid in the removal of the speaker enclosure ●...
- Page 8 Lower Speaker Removal ● Disconnect harness from the enclosure and module mounted on the back side, then remove from vehicle ● Remove the module from the OEM enclosure Page 8 of 33...
- Page 9 Dash Disassembly ● Install the module on the new enclosure using the OEM hardware ● On passenger side remove (4) Phillips screws Page 9 of 33...
- Page 10 Dash Disassembly ● Unclip and remove the panel on the side of the dash ● Using a panel tool carefully remove the grab handle cover (starting on the left) Page 10 of 33...
- Page 11 Dash Disassembly ● Remove (2) 10mm bolts securing the grab handle and set handle aside ● Unclip the airbag cover panel ● Remove (2) Phillips screws that have been exposed Page 11 of 33...
- Page 12 Dash Disassembly ● Remove glove box by opening and lifting the upper tab and removing the latch on the left side ● Remove three Phillips screws that have been exposed ● Looking in the glovebox cavity up high, remove two 13mm bolts securing the back of the passenger side airbag Page 12 of 33...
- Page 13 Dash Disassembly ● Carefully unclip the air bag. (this does NOT need to be removed from the vehicle) ● Lifting the airbag slightly will expose (5) Phillips screws that need to be removed Page 13 of 33...
- Page 14 Dash Disassembly ● Remove (3) Phillips screws holding the passenger speaker enclosure, then disconnect wires and remove from vehicle Page 14 of 33...
- Page 15 Upper Speaker Replacement ● If you are replacing the upper speakers as well, complete Steps 34 and 35 for driver and passenger side. Unclip and remove dash grill ● Remove (2) Phillips screws, disconnect wiring and remove speaker from vehicle ●...
- Page 16 Upper Speaker Replacement ● Install new speaker enclosure and secure with (3) Phillips screws ● Connect the speaker enclosure to the wiring Note – If just replacing the pods, but not adding amplifiers, then you will connect to OEM plug, but if you are adding amplifiers, then you will connect to the new harness.
- Page 17 Upper Speaker Replacement ● Lifting the airbag slightly and install (5) Phillips screws ● Remove (2) Phillips screws, disconnect wiring and remove speaker from vehicle ● Carefully clip the airbag into place Page 17 of 33...
- Page 18 Upper Speaker Replacement ● Looking in the glovebox cavity up high, install (2) 13mm bolts securing the back of the passenger side airbag ● Install (3) Phillips screws at bottom of glovebox opening ● Install glovebox by installing bottom hinge and pivoting up. (Also install left side gear arm) Page 18 of 33...
- Page 19 Upper Speaker Replacement ● Install (2) Phillips screw at the bottom of the passenger airbag ● Clip the airbag cover panel into place ● Install (2) 10mm bolts securing the grab handle Page 19 of 33...
- Page 20 Upper Speaker Replacement ● Slide ears on cover into slot and snap grab handle cover into place ● Install (5) Phillips screws on the side of dash ● Clip the passenger side dash cover into place Page 20 of 33...
- Page 21 Upper Speaker Replacement ● Install (4) Phillips screws on the top of the air bag ● Connect the speaker enclosure to the wiring Note – If just replacing the pods, but not adding amplifiers, then you will connect to OEM plug, but if you are adding amplifiers, then you will connect to the new harness.
- Page 22 Lower Speaker Install ● Install (3) Phillips screw to secure the enclosure ● Install (1) 8mm bolt below the speaker ● Install (4) 10mm bolts below steering column. (one is hidden behind the cross brace behind the left down support) Page 22 of 33...
- Page 23 Dash Reassembly ● Connect and install driver side dash ● Install (2) Phillips screws on the top of the left dash ● Install (1) Phillips screw from lower left dash Page 23 of 33...
- Page 24 Dash Reassembly ● Install (1) Phillips screw from lower left dash ● Clip kick panel cover into place ● Install (5) Phillips screws on driver side of dash Page 24 of 33...
- Page 25 Dash Re-assembly ● Clip the dash side panel into place ● Clip the steering column shroud into place ● Install (2) Phillips screws on shroud Page 25 of 33...
- Page 26 Dash Reassembly ● Clip the instrument panel shroud into place ● Install (4) Phillips screws on the driver side securing instrument panel shroud ● Clip top of dash into place Page 26 of 33...
- Page 27 Dash Reassembly ● Install (1) Phillips screw ● Clip the radio shroud into place and install (2) Phillips screws ● Connect the wiring Page 27 of 33...
- Page 28 Dash Re-assembly ● Connect the wiring and clip the climate control panel into place ● Install and clip in place the lower steering column cover ● If you are replacing the top dash speakers, make sure to connect the wires that you passed from the lower pod to the speaker Page 28 of 33...
- Page 29 Upper Speaker Replacement ● Install speaker with (2) Phillips screws ● Clip top dash grill into place Page 29 of 33...
- Page 30 Rear Speaker Installation ● Remove four 5mm Allen bolts to remove the OEM Grill ● Remove and disconnect (4) T30 Torx screws from the port and (5) T20 Torx screws from both speakers ● Apply painter tape to the soundbar, then hold the 6x9 speaker mounting plate up and mark the speaker opening Page 30 of 33...
- Page 31 Rear Speaker Installation ● Remove 6x9 mounting plate to show roughly the cutting and using a rotary cutting tool, cut a hole similar to the picture on the right BE VERY CAREFUL not to cut the OEM wiring as this will be used with the 6x9 speaker ●...
- Page 32 Rear Speaker Installation ● Connect the harness adapter to the OEM plug and connect to the 6x9, then mount the 6x9 to the mounting plate using (4) M4 Screws and washers ● Mount the new soundbar grill for the 6x9 with the OEM 5mm bolts Page 32 of 33...
- Page 33 This equipment complied with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. MBQJ-STG6-1 REV 01 Page 33 of 33...