Hardware Configuration; Power Connections; Switches, Jumpers, And Leds; Table 3-1. Switch Description Of The Tsw14J59 - Texas Instruments SW14J59EVM JESD204C User Manual

www.ti.com

3 Hardware Configuration

This section describes the various portions of the TSW14J59EVM hardware.

3.1 Power Connections

The TSW14J59EVM hardware is designed to operate from a single supply voltage of +12 V DC at 4 Amps. The
power input is controlled by the on and off switch, SW1. 12 V is enabled on the FMC+ using switch SW5. Make
sure both switches are in the off position before inserting the provided power cable. Insert the connector end of
the power cable into J38 of the EVM. The board can also be powered up by providing +12 V DC to the red test
point, TP1, and the return to any black GND test point.
The typical power supply range for the TSW14J59EVM is 12 V with a power consumption of about
16.5W. TI recommends that at least a 4A rated supply be provided to the TSW14J59EVM due to the
current consumption increase when data is being captured by HSDC Pro.

3.2 Switches, Jumpers, and LEDs

3.2.1 Switches and Push-Buttons
The TSW14J59 contains several switches and push-buttons that enable certain functions on the board. The
description of the switches is found in
Component
SW1
SW2
SW3
SW4
SW5
3.2.2 Jumpers
The TSW14J59 contains several jumpers (JP) and solder jumpers (SJP) that enable certain functions on the
board. The description of the jumpers is found in
Component Description
J11 Disables VCCO_3V3 supply when installed
JP5 USB3.0 PMODE1 configuration. With shunt installed, this sets PMODE1 high
JP6 USB3.0 PMODE2 configuration. With shunt installed this sets PMODE2 low
J19 Disables VCCO_1V2 supply when installed
J4 Disables VCCO_1V8 supply when installed
J16 Disables MGTAVCC_0V9 supply when installed
J15 Disables MGTAVTT_1V2 supply when installed
J17 Disables MGTAVCCAUX_1V8 supply when installed
J10 Disables VCCO_2V5 supply when installed
J21 Output SYNCA/B/C and input TRIG_IN translator voltage level select. With shunt on pins
1–2, voltage is 3.3V. With shunt on pins 2–3, voltage is controlled by TP30.
J28 Buffers U38, U44, U46 enable. With shunt on pins 1–2, U44 is enabled and U38 and U46 are
disabled. With shunt on pins 2–3, U44 is disabled and U38 and U46 are enabled.
J29 USB2.0 JTAG MUX enable. With shunt on pins 1–2, MUX is enabled. With shunt on pins
2–3, MUX enable is controlled by USB2.0 device.
J30 U47 buffer enable. With shunt on pins 1–2, U47 is disabled. With shunt on pins 2–3, U47 is
enabled.
J34 Status LEDs enable. With shunt on pins 1–2, LEDs are disabled. With shunt on pins 2–3,
LEDs are enabled.
SLWU095 – APRIL 2023
Submit Document Feedback
Table 3-1.
Table 3-1. Switch Description of the TSW14J59 Device
12 V Input power switch
FPGA reset
UCD Power monitor reset
USB reset
FMC+ 12,V power switch
Table

Table 3-2. Jumper Description of the TSW14J59 Device

Copyright © 2023 Texas Instruments Incorporated
Note
Description
3-2.
TSW14J59EVM JESD204C Data Capture and Pattern Generator Card
Hardware Configuration
Default
Open
Open
Installed
Open
Open
Open
Open
Open
Open
1 to 2
1 to 2
2 to 3
1 to 2
1 to 2
5