HC40 Advanced | Contents Preface ������������������������������������������������������������������������������������������������������������������������������������������ 4 Terms of use ���������������������������������������������������������������������������������������������������������������������������������� 5 Important safety information ��������������������������������������������������������������������������������������������������������� 6 General safety instructions ��������������������������������������������������������������������������������������������������������� 7 Only for EU markets������������������������������������������������������������������������������������������������������������������� 9 Only for Non EU markets ����������������������������������������������������������������������������������������������������������� 9 Misuse ��������������������������������������������������������������������������������������������������������������������������������������� 9 Informations de sécurité importantes ������������������������������������������������������������������������������������������� 10 Consignes générales de sécurité...
This User Manual does not address the end user� It is intended as a source of information for the equipment or system manufacturer only, and it will tell you how to install, use and maintain your LINAK electronics� The manufacturer of the end product has the responsibility to provide a User Manual where relevant safety information from this manual is passed on to the end user�...
LINAK, LINAK subsidiaries, or LINAK affiliates� All sales are subject to the ‘Standard Terms of Sale and Delivery for LINAK A/S’ available on LINAK websites� LINAK and the LINAK logotype are registered trademarks of LINAK A/S� All rights reserved�...
Failure to comply with instructions marked with the ”NOTICE” symbol may result in serious damage to the system or one of its components� Read all instructions before using this product� Important safety information on LINAK products can be found under the following headings: ®...
HC40 Advanced | General safety instructions Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed� Failure to comply with instructions marked with the ”NOTE” symbol may result in serious damage to the system or one of its components�...
Page 8
HC40 Advanced | This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation •...
HC40 Advanced | Only for EU markets This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved�...
Le non-respect des instructions marquées du symbole “AVIS” peut entraîner de graves dommages au système ou à l’un de ses composants� Lisez toutes les instructions avant d’utiliser ce produit� Des informations de sécurité importantes sur les produits LINAK peuvent être trouvées sous les rubriques ®...
HC40 Advanced | 11 Consignes générales de sécurité Le non respect de ces instructions peut entraîner des accidents impliquant des blessures graves� Ne pas suivre ces instructions peut entraîner l´endommagement ou destruction du produit� L´utilisation en toute sécurité du système n´est possible que si l´intégralité des instructions ont été lues et ont été...
Page 12
HC40 Advanced | 12 Cet appareil est pleinement conforme à la section 15 des réglementations FCC. Le fonctionnement est sujet aux deux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences dangereuses, et (2) cet appareil doit supporter les interférences, y compris celles pouvant provoquer un fonctionnement non désiré...
HC40 Advanced | 13 Seulement pour les marchés au sein de l´UE Cet appareil peut-être utilisé par des enfants âgés de 8 ans et plus, ainsi que les personnes dont les capacités physiques, sensorielles ou mentales sont réduites ou ayant un manque d´expérience et de connaissance si elles ont bénéficié...
EU DECLARATION OF CONFORMITY LINAK A/S Smedevænget 8 DK - 6430 Nordborg hereby declares under our sole responsibility that LINAK actuator system items Wireless accessory: BLE2LIN Wireless handset: HC05BL, HC10BL, HC1ABL, HC10ECO, HC2xBL, HC30BL, HC40BL, BP10BL, DPG1B, DPG1C, DPG1M, DPI-C complies with the Radio Equipment Directive (RED) 2014/53/EU (OJ L 153, 22.5.2014, p.
UK Declaration of Conformity LINAK A/S Smedevænget 8 DK - 6430 Nordborg hereby declares under our sole responsibility that LINAK Actuator System items: Wireless accessory: BLE2LIN Wireless handset: HC05BL, HC10BL, HC1ABL, HC10ECO, HC2xBL, HC30BL HC40BL, BP10BL, DPG1B, DPG1C, DPG1M, DPI-C Complies with Radio Equipment Regulations 2017 according to following standards: Safety Reg.
Use the HC40BL in an environment with temperature between -10 and +50 ºC� Otherwise, the HC40BL may be damaged� It can be operated at altitudes up to 2000 m� Hereby, LINAK A/S declares that the radio equipment type HC40BL is compliant with Directive 2014/53/EU� Caution: For battery: Risk of explosion if the battery is replaced with an incorrect type�...
HC40 Advanced | 17 Warranty This HOMELINE product is subject to warranty pursuant to the terms of the LINAK HOMELINE Warranty ® ® Paper� Maintenance Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for damage and breaks�...
HC40 Advanced | 18 Batteries HC40 FRAME™ The hand control needs two AAA batteries� 1� Press the button located inside the oval arch at the bottom of the hand control� Take off the battery lid� 2� Put in the new batteries as indicated in the housing�...
HC40 Advanced | 19 HC40 TWIST™ The hand control needs two AAA batteries� 1� Open the battery lid on the front of the HC40, by pressing and sliding it in the opposite direction of the keypad� 2� Put in the new batteries as indicated in the housing�...
HC40 Advanced | 20 Getting started Navigation The HC40 has ten buttons� The picture below explains the functionality of the buttons: Button 2 - refers to text in display Button 1 Button 3 - refers to text - refers to text in display...
HC40 Advanced | 21 Setting time and day 1� Press button 1 to switch between 24H and AM/PM� 2� Adjust the time by using the ‘up’ and ‘down’ buttons on the keypad� Once the hours and minutes are adjusted, “SAVE” appears in the display� Press the ‘select’ button or button 3 “SAVE” to save the time�...
HC40 if the hand control is delivered to the end user with batteries in� We recommend the same to LINAK salespeople before a customer visit� The software can be prepared before the visit, but before starting the trip to the customer, please take out the batteries�...
HC40 Advanced | 23 Demo mode and how to pair As long as the remote is not paired to any actuator system, the menu structure will be accessible to loop around in for demonstration purposes� We call this demo mode�...
HC40 Advanced | 24 Favourite positions Saving favourite positions The HC40 allows for storing up to four favourite positions� 1� Drive the bed to the desired position� 2� Loop to the “SAVE FAVOURITE” screen using the ‘left’ and ‘right’ buttons�...
Page 25
HC40 Advanced | 25 From the screen with the favourite position, there are three options: A. Driving to the favourite position 1� Press and hold button 3 ”GO TO” or the ‘select’ button� 2� The system now drives towards the position while the name flashes in the display�...
Page 26
HC40 Advanced | 26 C. Deleting a favourite position 1� Press button 1 “DELETE”� 2� Confirm the deletion by pressing button 3 “YES”� 3� The position is now deleted and removed from the general menu loop�...
HC40 Advanced | 27 Massage Controlling massage The HC40 can control up to two massage references� The two standard options are called “MASSAGE BACK” and “MASSAGE LEG”� Loop in the menu to find the massage screens� From the massage screen it is possible to: •...
HC40 Advanced | 28 Changing massage mode 1� Press button 2 “MODE” to change massage mode� 2� A green circle appears, and the massage mode is now changed� 3� Repeat to toggle between more available modes� Note: The number of massage modes depends on the configuration in the actuator system�...
HC40 Advanced | 29 Adjusting intensity 1� Use the ‘up’ button to increase the massage intensity� 2� Use the ‘down’ button to decrease the massage intensity�...
HC40 Advanced | 30 MY BED menu The “MY BED” menu is accessed by looping the menu with the ‘left’ or ‘right’ button, or via button 3 “MENU” on the main screen� Once “MY BED” appears, press the ‘select’ button to access the “MY BED”...
HC40 Advanced | 31 ABOUT The “ABOUT” section contains information about the product: the item number, the software number and version, and whether the control has been reconfigured� The item and software numbers also appear on the product label underneath the battery lid�...
Page 32
HC40 Advanced | 32 In the “ME” section it is possible to enter a name� By entering a name, the notifications get personalised, meaning “HAVE A NICE DAY” is now followed by the entered name� 1� Highlight the “ME” bar in the “MY BED” menu and press the ‘select’ button�...
HC40 Advanced | 33 ALARMS The alarm menu is accessible for systems including massage� When the alarm goes off, the massage motors start, providing a soundless wake-up� 1� Highlight the “ALARMS” bar in the “MY BED” menu and press the ‘select’ button to access the alarm menu, which contains three alarms�...
HC40� When the timer elapses, the bed drives to flat position and he can sleep in a comfortable position� The sleep timer functionality requires impulse drive enabled� The LINAK subsidiary and customer must have a written agreement that the customer takes full responsibility for this functionality�...
HC40 Advanced | 35 SHORTCUTS It is possible to set shortcuts on the HC40� The shortcuts are meant for the user to put in his/her most used features, so they are only one click away from the main screen� This way the hand control can be personalised to the needs of the individual user�...
HC40 Advanced | 36 TIME & DAY It is possible to adjust the time set during set-up of the hand control in the “TIME&DAY” menu in the “MY BED” menu� 1� Highlight the “TIME&DAY” bar in the “MY BED” menu and press the ‘select’ button to access�...
HC40 Advanced | 37 LANGUAGE The HC40 comes in ten different languages: English, French, Spanish, German, Swedish, Danish, Korean, Chinese, Finnish, and Norwegian� 1� Highlight the “LANGUAGE” bar in the “MY BED” menu and press the ‘select’ button to access the menu�...
HC40 Advanced | 38 CHILD LOCK It is possible to set a child lock on the HC40, meaning a specific button combination must be pressed to unlock the hand control before it is possible to run the bed� Enabling the child lock 1�...
HC40 Advanced | 39 TORCH On the backside of the hand control is a torch� Turning the torch on/off 1� Highlight the “TORCH” bar in the “MY BED” menu� 2� Press the ‘select’ button to enable the torch� The first five times a tip on how to turn on/off the torch by shaking the hand control shows� Press the ‘select’...
HC40 Advanced | 40 Notifications The HC40 sends notifications to the user to give a personal experience� When a name is typed in, the notification will adapt to that� The standard notification “HAVE A NICE DAY [name]” appears when the hand control is picked up in the time slot from 05�00 to 11�00 every third Saturday�...
LINAK service centre� In order to avoid the risk of malfunction, all actuator repairs must only be carried out by an authorised LINAK Service shop or repairers, as special tools and parts must be used�...
LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question�...
LINAK, LINAK subsidiaries, or LINAK affiliates. the same reason, LINAK cannot guarantee the correctness and actual status of imprinted information on All sales are subject to the ‘Standard Terms of Sale and Delivery for LINAK A/S’ available on LINAK websites. its products.
Need help?
Do you have a question about the HC40 Advanced and is the answer not in the manual?
Questions and answers