Table of Contents

Advertisement

Quick Links

HOLIDAY RAMBLER MOTORHOME LIMITED WARRANTY
WHAT THE PERIOD OF COVERAGE IS:
If you use your Holiday Rambler® motorhome only for recreational travel and
family camping purposes, the Limited Warranty provided by Holiday Rambler
("Warrantor") covers your new motorhome when sold by an authorized dealer, for
twelve (12) months from the original retail purchase date or the first 24,000 miles of
use, whichever occurs first. However, the Limited Warranty provided by Warrantor
covers the steel or aluminum frame structure of the sidewalls (excluding slide outs),
roof, and rear and front walls for sixty (60) months from the original retail purchase
date or the first 50,000 miles of use, whichever occurs first.
If you use your motorhome for any rental, commercial or business purposes
whatsoever, the Limited Warranty provided by Warrantor covers your new motorhome
when sold by an authorized dealer for ninety (90) days from the original retail purchase
date or the first 24,000 miles of use, whichever occurs first. In addition, the Limited
Warranty provided by Warrantor covers the steel or aluminum frame structure of the
sidewalls (excluding slide outs), roof, and rear and front walls for twelve (12) months
from the original retail purchase date or the first 24,000 miles of use, whichever occurs
first. A conclusive presumption that your motorhome has been used for commercial
and/or business purposes arises if you have filed a federal or state tax form claiming
any business tax benefit related to your ownership of the motorhome.
The above Limited Warranty coverage applies to all owners, including subsequent
owners, of the motorhome. However, a subsequent owner must submit a warranty
transfer form by filing the form through an authorized Holiday Rambler dealer. A
subsequent owner's warranty coverage period is the remaining balance of the warranty
coverage period the prior owner was entitled to under this Limited Warranty. Warranty
transfer forms can be obtained by contacting the Customer Relations Department.
There is no charge for the transfer.
LIMITATION OF IMPLIED WARRANTIES:
IMPLIED WARRANTIES, IF ANY, ARISING BY WAY OF STATE LAW,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY AND
ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE TERM OF THIS LIMITED
WARRANTY AND ARE LIMITED IN SCOPE OF COVERAGE TO THOSE
PORTIONS OF THE MOTORHOME COVERED BY THIS LIMITED
WARRANTY. Warrantor disclaims all implied and express warranties, including
the implied warranty of merchantability and the implied warranty of fitness for a
particular purpose, on components and appliances excluded from coverage as set forth
below. There is no warranty of any nature made by Warrantor beyond that contained
in this Limited Warranty. No person has authority to enlarge, amend or modify this
Limited Warranty. The dealer is not the Warrantor's agent but is an independent entity.
Warrantor is not responsible for any undertaking, representation or warranty made by
any dealer or other person beyond those expressly set forth in this Limited Warranty.
Some states do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you.
2006 Holiday RambleR limited waRRanty
WHAT THE WARRANTY COVERS:
Warrantor's Limited Warranty covers defects in the manufacture of your motorhome
and defects in materials used to manufacture your motorhome. "Defect" means the
failure of the motorhome and/or the materials used to assemble the motorhome to
conform to Warrantor's design and manufacturing specification and tolerances. Also
see the section "What the Warranty Does Not Cover" set out below.
WHAT WE WILL DO TO CORRECT PROBLEMS:
Warrantor will repair and/or replace, at its option, any covered defect if: (1) you
notify Warrantor or one of its authorized servicing dealers of the defect within the
warranty coverage period and within five (5) days of discovering the defect; and (2)
you deliver your Motorhome to Warrantor or Warrantor's authorized servicing dealer
at your cost and expense. It is reasonable to expect some service items to occur during
the warranty period. The performance of warranty repairs shall not extend the original
warranty coverage period. Further, any performance of repairs after the warranty
coverage period has expired or any performance of repairs to component parts and
appliances excluded from coverage shall be considered "good will" repairs, which shall
not alter the express terms of this limited warranty.
Warrantor may use new and/or remanufactured parts and/or components of
substantially equal quality to complete any repair.
Defects and/or damage to interior and exterior surfaces, trim, upholstery and other
appearance items may occur at the factory during manufacture, during delivery of
the motorhome to the selling dealer or on the selling dealer's lot. Normally, any such
defect or damage is detected and corrected at the factory or by the selling dealer during
the inspection process performed by the Warrantor and the selling dealer. If, however,
you discover any such defect or damage when you take delivery of the motorhome, you
must notify your dealer or Warrantor within five days of the date of purchase to have
repairs performed to the defect at no cost to you as provided by this Limited Warranty.
If either three or more unsuccessful repair attempts have been made to correct any
covered defect that you believe substantially impairs the value, use or safety of your
motorhome or repairs to any covered defect(s), which you believe substantially impairs
the value, use or safety of your motorhome, have taken 30 or more days to complete,
you must, to the extent permitted by law, notify Warrantor directly in writing of the
failure to successfully repair the defect(s) so that Warrantor can become directly
involved in exercising a final repair attempt for the purpose of performing a successful
repair to the identified defect(s).


Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vacationer Diesel 2006 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Holiday Vacationer Diesel 2006

  • Page 1 However, a subsequent owner must submit a warranty appearance items may occur at the factory during manufacture, during delivery of transfer form by filing the form through an authorized Holiday Rambler dealer. A the motorhome to the selling dealer or on the selling dealer’s lot. Normally, any such subsequent owner’s warranty coverage period is the remaining balance of the warranty...
  • Page 2 2006 Holiday RambleR limited waRRanty HOW TO GET SERVICE: EVENTS DISCHARGING WARRANTOR FROM OBLIGATION UNDER WARRANTY: The “Acknowledgement of Receipt of Warranty/Production Information” form must be returned to Warrantor promptly upon purchase to assure proper part replacement Misuse or neglect, accidents, unauthorized alteration, failure to provide reasonable and repair of your motorhome. Failure to return the “Acknowledgement of Receipt and necessary maintenance (See Owner’s Manual), damage caused by off road use, collision, fire, theft, vandalism, explosions, overloading in excess of rated capacities, of Warranty/Production Information”...
  • Page 3 2006 RoadmasteR limited waRRanty ROADMASTER CHASSIS LIMITED WARRANTY WHAT WE WILL DO TO CORRECT PROBLEMS: WHAT THE PERIOD OF COVERAGE IS: Warrantor will repair and/or replace, at its option, any covered defect if: (1) you notify Warrantor or one of its authorized servicing dealers of the defect within the If you use the Roadmaster Chassis that your motorhome is mounted upon for only warranty coverage period and within five (5) days of discovering any such defect; recreational travel and family camping purposes, the Limited Warranty provided by and (2) you deliver the Roadmaster Chassis to Warrantor or Warrantor’s authorized Roadmaster (“Warrantor”) covers your Roadmaster Chassis for thirty-six (36) months servicing dealer at your cost and expense.
  • Page 4 2006 RoadmasteR limited waRRanty HOW TO GET SERVICE: DISCLAIMER OF CONSEQUENTIAL AND INCIDENTAL DAMAGES: For warranty service simply contact one of Warrantor’s authorized service centers THE ORIGINAL RETAIL PURCHASER OF THE ROADMASTER for an appointment, then deliver your Roadmaster Chassis (at your expense) to the CHASSIS AND ANY PERSON TO WHOM THE ROADMASTER CHASSIS service center.
  • Page 5 Vacatoner Desel 2006 Sectons 1 ~ G ..................... 1 ection eneral nformatIon 2 ~ D & S ......................11 ection rIvInG afety 3 ~ e & I ....................45 ection xterIor nterIor 4 ~ a ........................67 ection pplIanCeS 5 ~ e ........................81 ection quIpment 6 ~ W...
  • Page 6 ©Copyright Holiday Rambler Corporation. All rights reserved. All other trademarks or registered trademarks are property of their respective holders. Brand name products of other companies mentioned in this manual are not endorsed by the manufacturer of the motorhome.
  • Page 7: ExterOr & InterOr Care - SectOn

    Vacatoner Desel 2006 General Informaton — Secton 1 Warranty InformatIon fIle ......4 reportIng Safety DefectS ......4 Safety termS ..........4 gloSSary of termS ........5 oWner’S manual Survey ......7 lImIteD Warranty tranSfer applIcatIon/ change of oWner InformatIon ....9...
  • Page 8 2006 section 1 — GeneRal infoRmation remedy campaign. However, NHTSA cannot POISON: Warranty InformatIon fIle become involved in individual problems between A warning or caution pertaining to safety you, your dealer or Monaco Coach. To contact and/or use of a poisonous substance or In addition to this Owner’s Manual you will NHTSA you may call the Auto Safety Hot line harmful chemical.
  • Page 9 2006 section 1 — GeneRal infoRmation TIP: Black Water - Term associated with the Direct Current (DC) - Power that is Tips contain information, helpful hints sewage holding tank. The toilet drains stored in a battery bank or supplied by and/or suggestion for ease of operation of the directly into this tank. photovoltaics, alternator, chargers and DC motorhome or its components. generators. Direct current is also known as CCA - Cold Cranking Amperage is the battery power.
  • Page 10 2006 section 1 — GeneRal infoRmation Pounds Per Square Inch Gauge (psig) - Grey Water - Term associated with the Wet Cell Battery - A type of battery that waste water holding tank. Water from the Pressure measured with respect to that of the uses liquid as an electrolyte.
  • Page 11 Owner’s Manual survey: vacationer Diesel 2006 Your suggestions are very important to us and we are continually striving 5. Were the operating instructions clearly written, and were you able to to improve the quality of our manuals. After becoming familiar with your...
  • Page 13 liMiTed WarranTy Transfer applicaTion/change of oWner inforMaTion Mail to: submitted By: limited warranty Transfer name: Monaco coach corporation address Change Warranty Transfer address: 91320 coburg industrial Way coburg, or 97408 City: state: Zip: Phone: ( Please read terms and representations below before signing. a.
  • Page 15: Table Of Contents

    Vacatoner Desel 2006 Drvng & Safety — Secton 2 DrIvIng & Safety ........... 12 Wheel mountIng ........... 31 Inspections........... 12 WeIghIng the motorhome ......32 Familiarize.Yourself........12 Weight.Terms..........32 Mirror.Adjust..........12 Weight.Label..........34 Safety.Seat.Belts........... 12 Four.Corner.Weighing.(Example)....
  • Page 16: Driving & Safety

    2006 section 2 — dRivinG & safety general inspection, which includes examining Using the socket wrench have the DrIvIng & Safety  the condition of the motorhome and the assistant loosen the bolt located at the surrounding area of the motorhome. Look high base of the arm. (See point A on the Section Two contains information on driving and low when walking around the motorhome.
  • Page 17 2006 section 2 — dRivinG & safety To fasten the seat belt, pull the belt out of the top of the safety seat. Secure safety seat retractors and insert the tab into the buckle; a harness straps at or below the shoulders (Example 1). click will sound when the tab locks into the buckle. Seat belt lengths automatically adjust to your size and sitting position. DO NOT route Toddlers - Children over one year and ...
  • Page 18: Driving Tips

    2006 section 2 — dRivinG & safety Seat Belt Care: require quick momentum changes. Increase Driving lanes in work zones can be  Keep the belt clean and dry. Clean with mild reaction time by paying attention to traffic and uneven, congested and narrower than soap and lukewarm water. DO NOT clean seat road conditions 12 to 15 seconds ahead of the usual.
  • Page 19 2006 section 2 — dRivinG & safety Right Turns: Left Turns: IMPORTANT SAFETY TIP Turn on the four way flashers if road DO NOT start the turn until the center Negotiating a right hand turn in a motorhome  speed degrades to the point where the can be difficult.
  • Page 20 2006 section 2 — dRivinG & safety Guidelines to Help Increase Fuel Efficiency: Extreme Heat and Hot Weather Conditions: Wet Conditions: Frequently observe all gauges. Variations Worn or improperly inflated tires can When starting out, apply the throttle    lightly and accelerate gradually. Avoid from normal conditions should be increase the risk of hydroplaning.
  • Page 21: Trip Preparation

    2006 section 2 — dRivinG & safety Operate the transmission with the Hand tools, a 12 Volt overhead cabinets. Close and secure all   MODE function set to Economy DC test light, a 120 cabinet doors and drawers, shower and whenever possible; this allows for earlier Volt AC polarity pocket doors. Turn off interior lighting.
  • Page 22: Hitch

    2006 section 2 — dRivinG & safety WARNING 2. Make the electrical connection and hItch Most states and Canadian provinces Using the Rear Receiver perform a light check before starting a require trailers and/or towed vehicles trip and at each rest stop. to have adequate auxiliary brakes.
  • Page 23: Rear Vision System

    2006 section 2 — dRivinG & safety communication while the camera is designed unit ON will allow continuous operation to provide the driver with a rear view when of the rear vision system when ignition backing up. The rear camera is adjustable up key is on. and down and is controlled by the driver. On the optional three camera system, CA. SEL. - Press this button to ...
  • Page 24: Backing Up A Motorhome

    2006 section 2 — dRivinG & safety remaining visible in the roadside mirror at all 3. Co-pilot uses both arms and hands BackIng up a motorhome times. The co-pilot should make a conscious parallel with thumbs pointing up and to effort to maintain sight of the driver through the rear in a waving vertical motion. This Whether you are a long time owner of roadside mirror as the motorhome maneuvers.
  • Page 25: Parking Brake

    2006 section 2 — dRivinG & safety Backing Up Trailers: 2. Hook up utilities and prepare appliances parkIng Brake for use: Towed vehicles using a tow bar or tow dolly have more than one pivot point and are not Open the LP-Gas tank primary valve. The motorhome parking brake is a foot  suitable for backing. Attempting to back up the Prepare the shore cord for connection.
  • Page 26: Dry Camping

    2006 section 2 — dRivinG & safety NOTE tanks are empty. Turn OFF interior 12 Volt DC power  To avoid shore power overload when To conserve water and fuel: whenever possible. Refrigerator, battery hooked to 30 Amp service, determine Operate the refrigerator on LP-Gas. Plan charging and inverter operation will not ...
  • Page 27: Breaking Camp

    2006 section 2 — dRivinG & safety NOTE hose with clean water from a non-potable BreakIng camp To extend/retract the slide-out room, hose. Store the hose. Replace the sewer the ignition must be OFF and the park cap. Preparing the motorhome for travel will brake set.
  • Page 28: Emergency Roadside Procedures

    2006 section 2 — dRivinG & safety Ensure jack pad is clear of debris when placing warning triangles depend upon the road of sudden tire failure, avoid heavy braking. Hold  characteristics and visibility. For example: The retracting hydraulic jacks. Loose rocks, the steering wheel firmly and gradually decrease...
  • Page 29 2006 section 2 — dRivinG & safety WARNING Battery Boost Switch: Next, start the generator. This may  Always ventilate the battery The Battery Boost switch engages a heavy- require using the Battery Boost switch compartment prior to any work or duty solenoid to electrically connect the house for the generator to start from the engine service to the batteries. Gas emitted by batteries to the engine battery in the event the battery.
  • Page 30: Towing Procedures

    2006 section 2 — dRivinG & safety CAUTION a support arm that goes under the motorhome DO NOT tow the motorhome from the  DO NOT use the towed vehicle for and secures to the front axle. Inform the tow rear. Towing from the rear will severely jump-starting. The charging system of...
  • Page 31: Tires

    2006 section 2 — dRivinG & safety Tread: Provides traction and cornering grip. of the utmost importance and must be a part of tIreS regular motorhome maintenance. Belts: Stabilize and strengthen the tread. Tires designed for the motorhome are a WARNING technically engineered product. Since the tire is Driving on a tire that is under-inflated...
  • Page 32: Tire.chart.-.Goodyear

    2006 section 2 — dRivinG & safety Always inflate tires to the Tire Chart - Goodyear pressure indicated in the i n f l a T i o n p r e s s U r e p s i tire chart for the load...
  • Page 33: Inspecting.&.Pressure

    2006 section 2 — dRivinG & safety Understanding the Inflation Table: Under-inflation can cause: axle. Ensure the valve cap is replaced on the The tire size is on the left margin of the table. stem after the inflation pressure is checked. Use Tire squeal on turns.
  • Page 34: Air.pressure.checklist

    2006 section 2 — dRivinG & safety WARNING 9. Check the sidewalls for gouges, cuts, Tire Vibration For safety purposes clear the area of bulges, or other irregularities. people and pets during tire inflation. Sudden tire failure is often preceded by tire Inflate tires using a remote inflation NOTE vibration.
  • Page 35: Tire.rotation

    2006 section 2 — dRivinG & safety circumference with the tire. Though the Wheel mountIng Tire Rotation For used nuts add two drops of oil sidewall of the tire may look structurally between flange and sound, weathering can occur inside Tire rotation can increase the useful life of the hex.
  • Page 36: Weighing The Motorhome

    2006 section 2 — dRivinG & safety Front Wheels: The Gross Axle Weight Rating (GAWR) of WeIghIng the motorhome Slide the front the axles is listed on the federal certification wheel over the label attached to the motorhome. This is Proper weight distribution, load management studs.
  • Page 37 2006 section 2 — dRivinG & safety The Federal Certification Label is a guide Weight of this motorhome as built at chassis components. How the motorhome is in knowing the maximum loaded axle weight factory with full fuel, engine oil and loaded will influence tire inflation pressure and coolants. UVW does not include cargo, rating GAWR, and subsequently the correct the load carried by each axle. This is why each tire inflation pressure for that weight.
  • Page 38: Weight.label

    2006 section 2 — dRivinG & safety NOTE Weight Label The most accurate method to determine proper tire pressure is four-point weighing. Each wheel position must be weighed independently. Weighing the entire axle will not accurately determine the total weight carried by that wheel position.
  • Page 39: Four.corner.weighing.(Example)

    2006 section 2 — dRivinG & safety Weigh the passenger side Four Corner Weighing (Example) rear corner (Scale D) and NOTE record weight on chart Scale Following scale readings and Gross Axle D, line 2. Example: 4,100 Weight Ratings are fictitious. Actual lbs. scale readings and Gross Axle Weight...
  • Page 40 2006 section 2 — dRivinG & safety Load and Inflation Table: Rated load capacities are listed for Water weight is the number of gallons   The load and inflation table helps to determine individual tires in a Dual or Single multiplied by 8.3. the correct inflation for the motorhome tire, position. LP-Gas weight is the number of gallons ...
  • Page 41: Cargo.carrying.capacity.flowchart

    2006 section 2 — dRivinG & safety Cargo Carrying Capacity (CCC) is how towed vehicle, are found in other areas of this manual. much cargo the motorhome can carry. However, tongue weight of a towed vehicle will further reduce this amount. Cargo Carrying Capacity Flowchart Now the motorhome can be fully loaded and weighed to ensure GVWR is not exceeded.
  • Page 42: Weighing.procedure.worksheet

    2006 section 2 — dRivinG & safety Weighing Procedure Worksheet example Worksheet 020255b conv...
  • Page 43: Weight.record.sheet

    2006 section 2 — dRivinG & safety actual Worksheet Weight Record Sheet 020255b...
  • Page 44: Smoke Detector

    2006 section 2 — dRivinG & safety batteries average a service life of one to Smoke Detector Maintenance two years. Steps to keep the smoke alarm working Statistics show that most fire casualties are properly: not caused by direct flame, but by less visible Test the smoke alarm once a week.
  • Page 45: Carbon Monoxide Detector

    2006 section 2 — dRivinG & safety WARNING carBon monoxIDe Detector Constant beeping and a flashing red light means CO gas has been detected. American National Standards Institute (ANSI) Shut off appliances, motorhome A119.2 - Fire & Life Safety 3-4.6 Carbon engine, and water heater.
  • Page 46: Alarm

    2006 section 2 — dRivinG & safety count to check that all persons are accounted for. One beep and one green flash indicate  Call the nearest fire department and ask them to memory is clear. Two beeps and two red flashes indicate determine the source of the Carbon Monoxide.
  • Page 47: Fire Extinguisher

    2006 section 2 — dRivinG & safety There are three classes of fire to be concerned fIre extInguISher eScape (egreSS) WInDoW with in a motorhome. Any fire can fall into more than one class; a fire that involves both burning...
  • Page 48 2006 section 2 — dRivinG & safety NoteS...
  • Page 49 Vacatoner Desel 2006 exteror & Interor Care — Secton 3 exterIor care ..........46 ShoWer ............55 Corrosion............46 ceIlIng............. 56 Washing............46 Wall coverIngS ..........56 Drying............46 WooD care ............57 Waxing............46 countertopS ..........58 Paint.Codes..........
  • Page 50: Exterior Care

    2006 section 3 — exteRioR & inteRioR caRe NOTE Washing Drying “Section 3 - Exterior Care & Maintenance” is a general cleaning Chamois cloths come in natural and synthetic Periodic cleaning will help to preserve the section. Some of the articles within this paint finish. The motorhome is painted with a materials.
  • Page 51: Paint.codes

    2006 section 3 — exteRioR & inteRioR caRe INFORMATION When selecting a product, the container should To Obtain the Paint Code: When selecting a product, follow the be marked, “safe for clear coats” or “clear 1. Contact National Parts at 1-877-466- product manufacturer’s recommended coat safe.” Carefully follow the application 6226. application instructions. instructions when using a product. Upon first 2.
  • Page 52: Tire.care

    2006 section 3 — exteRioR & inteRioR caRe WARNING Each wheel cover is secured by four lug covers Wheels - Coated Aluminum If the mask becomes wet it MUST BE identified by indent or notch markings. When removed or paint damage could result.
  • Page 53: Bright.metal

    2006 section 3 — exteRioR & inteRioR caRe NOTE 5. Carnauba wax can be applied to help motorhome, such as the “beltline” or vent When using chemicals to remove road protect the finish. attached on the roof, there is a seal preventing tars, use only automotive products that water intrusion. There are many types of...
  • Page 54: Sealant.types

    2006 section 3 — exteRioR & inteRioR caRe WARNING as paint thinner. Gloves are required as this Sealant Types Inspecting sealant will require use of considered a hazardous material. a ladder or scaffold assembly. Roof Rubber Sealant: access is also required. Follow proper...
  • Page 55: Interior Care

    2006 section 3 — exteRioR & inteRioR caRe InterIor care faBrIcS Vinyl Cockpit General Care & Cleaning Several areas of the motorhome, such as the Special care needs to be taken when the The cockpit area dashboard is a molded- dash, ceiling and items of furniture, may be motorhome is exposed to a very humid climate fiberglass, vinyl-wrapped pod. The instrument covered in vinyl. The care and cleaning of these for an extended period of time. Protect the fabric...
  • Page 56 2006 section 3 — exteRioR & inteRioR caRe Urine Stains: Latex Paint: will cause permanent staining. Rinse Sponge with soapy water containing a Fresh paint can be wiped off with a damp thoroughly with clean water. small amount of household ammonia. cloth. Hot soapy water will normally Rinse thoroughly with clean water.
  • Page 57: Leather

    2006 section 3 — exteRioR & inteRioR caRe CAUTION Disinfect with a 5:1 NON- Leather  If there is residue of bleach, the CHLORINATED (only) bleach polyurethane resin and back cloth will Spots & Spills: solution. deteriorate. Absorb excess liquid immediately with a clean Dry clean using commercial dry cleaning ...
  • Page 58 2006 section 3 — exteRioR & inteRioR caRe Pretest the spot removal agent in an household ammonia to one cup water.  inconspicuous area to make certain it will G. Stain Removal Kit: Available from not damage the carpet dyes. retail carpet stores or professional Apply a small amount of the cleaning cleaners.
  • Page 59: Tile.floor

    2006 section 3 — exteRioR & inteRioR caRe product. If there is any doubt, apply Tile Floor Laminate Floor several test patches of the solution in an inconspicuous place to determine Tile floors vary in porosity and surface Laminate flooring used in the motorhome product suitability.
  • Page 60: Ceiling

    2006 section 3 — exteRioR & inteRioR caRe Care for the Tower Wall Covering: Nail Polish, Shellac or Lacquer: To prevent excessive moisture and a continual Remove ordinary stains with Remove liquid using a dry cloth. Use growth of mildew, use the shower only with adequate ventilation. The sealant in a regularly mild soap and warm water.
  • Page 61: Wood Care

    2006 section 3 — exteRioR & inteRioR caRe Fixing scratches in stained woodwork: needed. Always sand with the grain. WooD care Light scratches will often disappear when griT grade carefully rubbed with furniture polish or paste For general cleaning, regularly wipe wood smoothing the surface, wax. When scratches appear lighter than the...
  • Page 62: Countertops

    2006 section 3 — exteRioR & inteRioR caRe Restoring the clear finish: Preventing Heat Damage: countertopS Check the scratches carefully. If flaking Solid Surface Hot pans and heat-generating appliances, such varnish is visible with dark-stained wood as frying pans or crockpots, can damage the Routine Care: underneath, only the clear finish may need to surface. To prevent heat damage, always use a The motorhome solid surface countertops and be restored.
  • Page 63: Stainless Steel Surfaces

    2006 section 3 — exteRioR & inteRioR caRe Controlling Moisture Condensation: StaInleSS Steel SurfaceS WInDoW treatmentS Reduce or eliminate interior moisture Mini-Blinds condensation during cold weather by using the Clean stainless steel once a week with a damp following steps: Dusting: sponge. Apply stainless steel cleaner/polish Partially open the roof vents and Regular dusting will maintain the appearance with the grain, not across, using a non-abrasive  of the mini-blinds. Keep aluminum blinds windows so that outside air can circulate cloth or sponge.
  • Page 64: Day/Night.shades

    2006 section 3 — exteRioR & inteRioR caRe are susceptible to mold. that ozone cleaners are not effective at killing Day/Night Shades Temperate climate and moisture also help airborne mold or surface mold contamination. Guidelines for care and maintenance of to cultivate mold growth. Moisture in the motorhome can result from unattended spills, Controlling Mold Growth: polyester blended day/night shades: leaks, overflows and condensation.
  • Page 65: Pest Control

    2006 section 3 — exteRioR & inteRioR caRe 5. Inspect for leaks on a regular basis. Keep foods such as flour, cereal, peSt control  Look for discolorations or wet spots. spaghetti and pet food in re-sealable Repair leaks promptly. Inspect containers with tight lids.
  • Page 66 2006 section 3 — exteRioR & inteRioR caRe Rodents: Regularly inspect the exterior of the that all fleas have encountered the treatment. Rodents may chew through wires or build motorhome for signs of a budding wasp nest, Flying outdoor insects are attracted to nests in components of the motorhome. Signs of and promptly destroy small nests before they bright light. Yellow porch light covers on the rodent infestation include droppings, shredded become too large.
  • Page 67: Storage

    2006 section 3 — exteRioR & inteRioR caRe Best sources of information about common Be sure to understand what is guaranteed If available, leave the motorhome   household pests: and what is not. hooked to shore power. Leave the main The Internet is a great place to find battery disconnect switches ON.
  • Page 68 2006 section 3 — exteRioR & inteRioR caRe NOTE CAUTION Cardboard templates can be made for  The natural process of condensation A 20 Amp service using light duty the windows to protect the interior from will occur with temperature changes extension cords and the required exposure to direct sunlight.
  • Page 69: Winter.storage.checklist

    2006 section 3 — exteRioR & inteRioR caRe Brakes: Fuel Tank - Diesel fuel tank should be Winter Storage Checklist  full of fuel. Brakes suffer from non-use during periods of storage. The bare metal machined surfaces of Plumbing Lines - Drain and protect by  brake drums or rotors have only a light coating filling with approved RV antifreeze.
  • Page 70 2006 section 3 — exteRioR & inteRioR caRe Check all the chassis fluid levels: engine Repair as necessary. Operate each LP-Gas appliance. Observe   oil, engine coolant, hydraulic fluid Operate all 12 Volt DC lights and all burner/pilot flames for proper color ...
  • Page 71 Vacatoner Desel 2006 Applances — Secton  applIanceS - IntroDuctIon ......68 refrIgerator ..........68 Operation.Specifics........68 Control.Panel.-.Two.Door......69 Control.Panel.-.Four.Door.(Optional)..... 69 Tips............. 70 Icemaker............70 Doors............71 Refrigerator.Alarm........71 Storage.Procedures........71 Service............72 mIcroWave/convectIon oven ....
  • Page 72: Appliances - Introduction

    2006 section 4 — appliances bulls eye (fence post) level. Place the levels on applIanceS - IntroDuctIon refrIgerator the bottom shelf of the refrigerator. The bubble Refrigerant is heated until it vaporizes. should be at least half-way inside the circles.
  • Page 73: Control.panel.-.Two.door

    2006 section 4 — appliances 030864c TEMP SET Button: When 120 Volts AC is available “AU  Adjusts the temperature. AC” flashes in the display. This indicates To adjust, push and hold the SET TEMP the refrigerator is operating on AC 040575  figure a button.
  • Page 74: Tips

    2006 section 4 — appliances Allow the refrigerator 24 hours of  operation before actual use to help get a head start with the refrigeration process. A box of open baking soda will help  absorb food odors. Ice build up can be slowed in high  humidity if the end of the drain tube is submersed in drip pan. It may be...
  • Page 75: Doors

    2006 section 4 — appliances NOTE when operating the refrigerator in any mode If the alarm sounds, note the code to help prevent moisture accumulation in high in the LED display and turn the humidity conditions. refrigerator off to silence the alarm. Mold and mildew may contaminate a INFORMATION completely sealed refrigerator in storage. The...
  • Page 76: Service

    2006 section 4 — appliances the microwave/convection oven to dry the test item works, contact an appliance Service clothes, newspapers, shoes or other repair facility to have the microwave/ items. convection oven checked. The LP-Gas function of the refrigerator and Steam accumulating inside or around LP-Gas pressure will require annual service.  NOTE...
  • Page 77: Range Hood

    2006 section 4 — appliances DO NOT use harsh detergent or abrasive Use the following procedure to remove the upward and slide in. Be careful not to cleaner. grease filter and hood light. kink or warp the filter upon installation. It is occasionally necessary to remove the 4. Lock in place by securing with the clip ...
  • Page 78: Burner.grate

    2006 section 4 — appliances The cooktop operates under the click. If the burner fails to light, continue amount of liquid is used. The choice turning the SPARK knob clockwise until following conditions: of cookware selected can make a big the burner lights. difference. The primary LP-Gas valve on the LP ...
  • Page 79: Cooktop With Oven (Optional)

    2006 section 4 — appliances Porcelain Enamel: Light the oven pilot After the burner lights, adjust the surface   Sharp blows, radical surface temperature located near the burner control knob between HI and changes, etc., will cause enamel to chip or back of the oven, LOW to select the desired flame size.  crack. Some foods, such as vinegar, lemon...
  • Page 80: Air Conditioning - Roof

    2006 section 4 — appliances NOTE Fan Operation: conditioning principle is reversed, supplying The Comfort Control must be ON to Circulates interior air by using heated air to the ceiling registers instead of operate any HVAC function. Do not the roof air conditioner blower. refrigerated air. There are ambient temperature select conflicting modes of operation.
  • Page 81: Return.air.filters

    2006 section 4 — appliances Press the UP or DOWN buttons to set furnace Operation  desired heating temperature. Select Zone 1 or Zone 2, using the The furnace operates in the following The furnace and its related components  MODE button. manner: The wall thermostat sends a signal are 12 Volt DC operated, using LP-Gas as the to the front roof air conditioner circuit board, fuel source. Electronic circuitry (automatic which closes a relay. Closing a relay sends ignition) is used to ignite the burner.
  • Page 82: Using.the.furnace

    2006 section 4 — appliances Water heater Using the Furnace If the Furnace Fails to Light Slide the ON/OFF switch The water heater uses two different methods If the furnace fails to light make sure the  (on wall thermostat) to the LP-Gas primary supply valve is open. The to heat water: (1) 120 Volt AC, supplied either ON position.
  • Page 83 2006 section 4 — appliances To Purge Air and Pressurize the System: Water Heater Operation: NOTE LP-Gas and 120 Volt AC functions can Turn the water heater bypass valve Turn on the   be on at the same time. This will speed (located at the back of the water heater) battery cut-out up the process of heating water for to Normal Flow.
  • Page 84 2006 section 4 — appliances The bypass valve water heater. it will use approximately 12 Amps at 120 is located on the 4. Open the handle Volts AC. Appliances that operate from back of the water of the P & T 120 Volts AC may need to be operated in heater in a curbside valve.
  • Page 85 Vacatoner Desel 2006 equpment — Secton  eQuIpment - IntroDuctIon ......82 Sofa ..............92 entry Step............82 Jack.Knife.Sleeper.Sofa......... 92 Operation............82 Hide-A-Bed.(Optional)........93 Stepcover............. 83 Air.Mattress.(Optional)........93 entry Door ............ 83 Booth DInette ..........93 Latch.Adjustments........83 Bed.Conversion.
  • Page 86: Equipment - Introduction

    2006 section 5 — equipment WARNING 3. Open the door. The step should extend eQuIpment - IntroDuctIon If the motorhome is driven with the and lock in the OUT position. The step step in the extended position there is the will retract when the door is closed.
  • Page 87: Stepcover

    2006 section 5 — equipment good operating condition requires some routine down movement for vibration control in Stepcover maintenance items on a regular basis. travel. Cover: Test the operation of the dead bolt lock  to ensure proper function. An electrically operated stepwell cover will Latch Adjustments Apply silicone weekly to the entry door extend and retract using the switch on the center ...
  • Page 88: Slide-Out Operation

    2006 section 5 — equipment Adjusting the Screen Door for In and Out awning if extended in snow, sleet, ice or products can damage the paint and will freezing rain. In such conditions, if the cause premature aging of the rubber...
  • Page 89: Manual Override

    2006 section 5 — equipment WARNING WARNING 5. Attach a 1/4” socket and ratchet or drill The outside area must be clear of DO NOT work on slide-out system to the other end of the flexible shaft. obstructions that can restrict slide unless the battery is disconnected.
  • Page 90: Awnings

    2006 section 5 — equipment If the slide room does not operate after 5. Once the slide room has been manually Attach to checking the safety requirements: retracted, reconnect power supply. rachet or drill. Check the fuses in the roadside This is necessary to stop the slide room  front electrical box and the bedroom from moving once retracted.
  • Page 91: Entry.door.awning.(Optional)

    2006 section 5 — equipment CAUTION Entry Door Awning (Optional) When the awning is at full extension do not allow the awning to snap back into To Extend the the retracted position. Personal injury Awning: or damage to the awning or motorhome Unlock front arm may occur.
  • Page 92 2006 section 5 — equipment NOTE Ensure the locking tab on the support brace is latched through in the hole in the end cap. 4. If equipped with Canopy Clamps, fasten the clamps at this time. 5. Using the arm extension...
  • Page 93 2006 section 5 — equipment 2. Support the weight of the up on the awning. To position the awning in the 4. Raise the rear arm extension lock awning with one hand while rain release setting, lower one arm of the awning handle all the way up or to the desired opening the extension lock and leave the other arm in the normal position.
  • Page 94: Patio.awning.-.Eclipse.(Optional)

    2006 section 5 — equipment To Operate: Vinyl Awnings - Mildew will not form on the Patio Awning - Eclipse (Optional) Turn the ignition switch OFF. awning material itself, but it may form on the  Check for sufficient clearance before dust accumulated on the canopy. A quality vinyl The Eclipse is a box awning that operates on ...
  • Page 95: Fans

    2006 section 5 — equipment The awning was not designed to WARNING NOTE withstand the 500 to 700 pounds of Do not hold switch after the motor has DO NOT leave the fan switch in the water that could accumulate on the stopped.
  • Page 96: Seat Controls

    2006 section 5 — equipment NOTE If, for any reason, the pocket door needs to be Sofa The seats operate from 12 Volt DC house removed, locate the portion that is secured to the Jack Knife Sleeper Sofa power. The house battery and battery top of the pocket door and rotate the small lever cut out switch must be on to operate the outward to release the latches.
  • Page 97: Hide-A-Bed.(Optional)

    2006 section 5 — equipment Sleeper to Sofa: Plug in the pump Hide-A-Bed (Optional)  Remove all bedding from the hide-a-bed. motor to inflate to a  The sofa hide-a-bed will convert easily into Grasp the foot of the hide-a-bed in the desired firmness.
  • Page 98: Free Standing Dinette (Optional)

    2006 section 5 — equipment Use both seat cushions and one back Storage unDer BeD laDDer - rear  cushion for a mattress. Leave one back To use the storage compartment located under cushion in a vertical position. The rear ladder allows access to the roof. Care the bed, lift up the bed by the front edge of the should be used when climbing the ladder. Access mattress platform.
  • Page 99: Television.(Front).Lockout.feature

    2006 section 5 — equipment CAUTION Television (Front) Lockout Feature TV Antenna DO NOT move motorhome with antenna in the raised or partially The television antenna is a manual crank style The ignition switch controls the outlet for the raised position and risk damage by tree antenna with built in electronics that use 12 front TV, allowing the front TV to be operated limbs or wires. Worm gear damage or Volts DC to “boost”...
  • Page 100 2006 section 5 — equipment Video switch allows independent Press the TV ANT button located in the Initiate a channel Auto Search to scan    viewing of signals on different area marked “MAIN TV.” available channels. Exit menu. televisions with a record option from On the television press the TV/VIDEO Select desired channel for viewing.
  • Page 101: Satellite.system.-.Dss.prewire

    2006 section 5 — equipment To Watch Front Television from a DVD: preset stations. home theatre SurrounD SounD On the television press the TV/VIDEO The CD/DVD player features single disc auto – (optIonal)  button and select VIDEO. The word load, random shuffle track playback, repeat and “VIDEO”...
  • Page 102: Systems Control Center

    2006 section 5 — equipment 7. Water Heater Switch - Applies 120 SyStemS control center Volt AC power to the Water Heater, if preferring to operate the Water Heater The System Control Center enables a central with 120 Volts. location for many of the switches and control monitors used to operate the motorhome. This 8. Slide-Out Room Controls - Provides panel is a flush wall-mounted unit.
  • Page 103 Vacatoner Desel 2006 Water Systems — Secton 6 Water SyStemS - IntroDuctIon ....100 Water tankS ..........100 Measurements.&.Calibration....... 100 Fresh.Water.Fill.......... 100 City.Water.Hook-up........101 Water pump ..........101 Water.Pump.Troubleshooting...... 102 Water fIlter - faucet ....... 102 Water SyStemS ..........
  • Page 104: Water Systems - Introduction

    2006 section 6 — wateR systems Waste Water System: Water SyStemS - IntroDuctIon Fresh Water Fill The waste water system consists of a waste holding tank (grey water), sewage holding tank When connecting the motorhome to fresh This section contains (black water), flush system, toilet and drains. water, use a hose manufactured and labeled information about the “for potable water.” This ensures that the hose operation and care of various WARNING will not flavor the water.
  • Page 105: City.water.hook-Up

    2006 section 6 — wateR systems 4. Connect the other end of the hose to the 1. Install the provided pressure regulator water source. on the city/fresh water fill valve. Arrow 5. Turn the City/Fresh on regulator must be pointed towards Water Control Valve valve.
  • Page 106: Water.pump.troubleshooting

    2006 section 6 — wateR systems The water pump can be operated from by tightening the hardware. Check the following leaky toilet or valves. these following locations: items: Look for a loose drive assembly or pump  Hallway Systems Control Panel head screws.  Water Service Center Water pump will not start or blows the fuse: ...
  • Page 107: Water Systems

    2006 section 6 — wateR systems • Store diverter hose for use 5. Use a small funnel to pour the correct Disinfecting Fresh Water amount of disinfecting solution into the when winterizing the water Disinfecting the water system with household hose. system. 6. Hook one end of another potable water bleach (superchlorination) protects against hose to the short hose and the other end bacteriological or viral contamination from A fresh replacement cartridge to a water source.
  • Page 108: Faucet Screens

    2006 section 6 — wateR systems INFORMATION DO NOT use any type of tissue that WaSte Water SyStemS Household bleach is 5.25% Sodium Proper Waste Disposal remains in one piece. Paper designed Hypochlorite. Higher concentration will specifically for holding tanks is available increase PPM ratio.
  • Page 109: Waste.drain.hose

    2006 section 6 — wateR systems Black Water Tank: The shore fitting for the sewer hose may be a The black water valve remains closed until Before initially operating the toilet, treat the three or four-inch, male or female thread pipe; the tank is full or until time of departure to help sewage holding tank with a pre-charge of water or a four-inch pipe with no threads, covered prevent clogging. Use the outside faucet or and an odor-control chemical (available at most by a metal plate.
  • Page 110: Toilet

    2006 section 6 — wateR systems WARNING CAUTION Dumping the Tanks: Never operate the flush system To prevent 1. When preparing to dump the black unattended. Flooding may occur. Use the accumulation of solids tank, first close the grey water valve.
  • Page 111: Cleaning.&.Maintenance

    2006 section 6 — wateR systems AutoVents: Water flow pressures vary. Therefore, holding height. Adjust the flange height to 7/16" above floor, if necessary. Replace flange the flush lever down for several seconds may be The auto vent seal if damaged.
  • Page 112: Cold.weather.storage

    2006 section 6 — wateR systems recommendation for winterization. System Heat Operation: 3. Drain the fresh water tank by opening 1. Systems heat switch the fresh water tank drain valve located is turned ON to apply in a curbside compartment. WInterIzatIon power to the snap disc thermostat. Water, plumbing and sewer systems require 2. When the bay...
  • Page 113: Using.non-Toxic.antifreeze

    2006 section 6 — wateR systems 8. After the water is drained 14. Shut off the air compressor and 2. Remove water faucet filter cartridge and connect an air hose to disconnect the air hose. replace filter with diverter hose. (See the City/Fresh Water Fill 15.
  • Page 114: De-Winterization

    2006 section 6 — wateR systems 13.Connect a hose to the City/Fresh Water 20. If the motorhome is equipped with an connection and place the other end into ice maker, remove the valve outlet the container of antifreeze. line located in the outside refrigerator access compartment. Cycle ice maker several times until antifreeze is present.
  • Page 115: Water Service Center

    2006 section 6 — wateR systems Water ServIce center...
  • Page 116: Water System Diagram

    2006 section 6 — wateR systems Water SyStem DIagram 040487q NOTE Drawing is a general depiction of Water System Layout.
  • Page 117 Vacatoner Desel 2006 LP-Gas Systems — Secton 7 lp-gaS SyStemS .......... 114 lp-gaS Detector ........114 Testing............115 Alarm............115 Maintenance..........116 lp-gaS emergency proceDureS checklISt ............ 116 lp-gaS tank ..........116 Measurement..........116 Tank.Capacity..........
  • Page 118: Lp-Gas Systems

    2006 section 7 — lp-Gas systems WARNING accessory control valves. All fittings lp-gaS SyStemS When storing portable LP-Gas tanks tested should be thoroughly rinsed and that are not connected to an LP-Gas dried after testing. Never attempt to...
  • Page 119: Testing

    2006 section 7 — lp-Gas systems LP-Gas is heavier than air and will settle to propellant used in spray cans and cleaning Testing the lowest point in the motorhome. The LP-Gas solvents. In some cases, vapors from glue and Press the TEST switch any time during the...
  • Page 120: Maintenance

    2006 section 7 — lp-Gas systems 2. Turn off 4. After two minutes the detector will primary return to normal operation (solid valve green) or resound the alarm if on the dangerous levels of gas remain in the LP-Gas area. tank. 050250d Fault Alarm: 050272 Determine and repair the source of the Should the microprocessor sense a fault in the leak. If necessary, contact a qualified gas detector, a fault alarm will sound twice every DO NOT operate any electric switch.
  • Page 121: Tank.capacity

    2006 section 7 — lp-Gas systems WARNING NOTE The monitor uses Before entering a refueling station, turn If the tank is new and being filled for the colored lights with a off all pilot lights and LP-Gas operated first time, inform the service technician corresponding scale appliances.
  • Page 122: Accessory.hookup

    2006 section 7 — lp-Gas systems lp-gaS funDamentalS Accessory Hookup Exterior Gas Line Hookup Prep: An auxiliary remote LP-Gas hookup is for external LP-Gas accessories and is to be used for external components only. For safety, only approved LP-Gas quick disconnect fittings and flexible hose should be used to connect external accessories to the remote hookup.
  • Page 123: Lp-Gas Regulator

    2006 section 7 — lp-Gas systems Under normal atmospheric conditions an Damage to the regulator can occur when the lp-gaS regulator LP-Gas regulator will not freeze, nor will the tank is overfilled. The regulator is designed LP-Gas is compressed into liquid form in the LP-Gas. Vapor passing through the regulator to work with vapor only.
  • Page 124: Lp-Gas Hose Inspection

    2006 section 7 — lp-Gas systems Slippage; evidenced by the misalignment lp-gaS hoSe InSpectIon  Attach the manometer of the hose and coupling and/or the gauge to the accessory It is suggested by the hose manufacturer that scored or exposed area where slippage hookup line to avoid a flexible LP-Gas supply hose undergo regular has occurred.
  • Page 125: Lp-Gas Consumption

    2006 section 7 — lp-Gas systems LP-Gas appliances are rated in Input Divide the total of BTUs of the LP-   BTU (British Thermal Units). The rating Gas tank by the total number of BTUs is usually stamped or printed on a tag the appliances consume, equals the affixed to the appliance.
  • Page 126 2006 section 7 — lp-Gas systems DO NOT cover the oven bottom with The motorhome is equipped with many  LP-Gas operated appliances because it is a foil. Air circulation will be restricted. Never use LP-Gas ranges or ovens for convenient and efficient source of fuel. LP-Gas ...
  • Page 127 Vacatoner Desel 2006 electrcal Systems - House — Secton 8 houSe electrIcal - IntroDuctIon ..124 converter (55 amp only) ......125 Battery DISconnect ........125 House............125 Battery cut-out SWItch ......126 Shore poWer hook-up ......126 tranSfer SWItch ........
  • Page 128: House Electrical - Introduction

    8 — electRical systems - House vacationeR diesel 2006 WARNING The panels contain fuses for the house, interior houSe electrIcal - IntroDuctIon The electrical system is engineered lighting and appliances such as the furnace and and tested for safety. Circuit breakers the water heater. This section contains guidelines, procedures and fuses protect the electrical circuits Each panel electrical circuits may be protected and information that assist in understanding from overloading.
  • Page 129: Converter (55 Amp Only)

    2006 section 8 — electRical systems - House NOTE Be careful when using outlets that are applying the power converter is functioning properly. When using adaptors, care will loads such as electric motors, heaters, coffee The converter is located in the rear curbside have to be used when operating the makers, toasters, hair dryers or other large compartment. appliances and using the outlets to avoid current consuming loads.
  • Page 130: Battery Cut-Out Switch

    8 — electRical systems - House vacationeR diesel 2006 Plugging in the Shore Cord: Some are federal Shore poWer hook-up mandate items, such Located in the roadside compartment is  the shore power cord. as the LP detector. If The power requirement the motorhome is not Unscrew the deck plate and extend a for the motorhome is 30 ...
  • Page 131: Transfer Switch

    2006 section 8 — electRical systems - House Disconnecting the Shore Cord: Another common adapter is a 30 to 20 Amp tranSfer SWItch Turn off all AC appliances. This will adapter. This type of connector adapts the 30 ...
  • Page 132: Pre-Start.checks

    8 — electRical systems - House vacationeR diesel 2006 The generator can be started from the NOTE nearby vehicles. Operate the generator The generator may stop running or will only when there is a safe dispersion of following locations: not start before the chassis fuel tank exhaust.
  • Page 133: Powering.the.equipment

    2006 section 8 — electRical systems - House in sequence rather than at the same time. If the circuit breaker Powering the Equipment immediately trips, the INFORMATION electrical distribution The AC output of the generator powers the The generator may shut down for system has a short or the motorhome air conditioners, the AC Inverter/ reasons other than an overload.
  • Page 134: Inverter - 140 Watt (Optional)

    8 — electRical systems - House vacationeR diesel 2006 Inverter - 140 Watt (optIonal) DIStrIButIon panel (30 amp) House 120 Volt AC Panel When the inverter The AC is turned ON and distribution shore power or panel is located generator (optional) in a bedroom power is not used, 060318 overhead the inverter operates 140 Watt Inverter cabinet.
  • Page 135: Gfci.breakers.&.Outlets

    2006 section 8 — electRical systems - House For example: A breaker with a 20 Amp can be felt, but such a shock is considerably less GFCI Breakers & Outlets rating will operate a continuous 16 Amp load. than one without ground fault protection. People This design leaves a small amount of working with heart conditions, or other conditions that A ground fault circuit interrupter capacity within the breaker.
  • Page 136: Distribution Panel

    8 — electRical systems - House vacationeR diesel 2006 the same amperage. If a higher rated fuse is DIStrIButIon panel BatterIeS - houSe House 12 Volt DC installed it can damage the wiring. Fuse current set points follow much of the same electrical House batteries are designed for use with The 12 Volt house contains fuses (located in principle as the 120 Volt AC breakers. Using 12...
  • Page 137: Battery.maintenance

    2006 section 8 — electRical systems - House Check the battery connections for tightness Battery Maintenance Testing the Battery and corrosion. If corrosion is found, disconnect the cables (mark cable locations) and carefully Liquid Lead Acid (LLA) battery cells A battery can be tested clean them with a mild solution of baking soda should be checked at least once a month. The...
  • Page 138: Battery Charge Time & Consumption Rate

    8 — electRical systems - House vacationeR diesel 2006 Placing a load on the Battery: Temperature and recent battery activity with different battery types and chemical (charging or discharging) affect the hydrometer Another test that can be performed is to place compositions. Deep cycle batteries are generally a specific load on the battery for a predetermined readings.
  • Page 139: Lights

    2006 section 8 — electRical systems - House Increasing the load applied to the battery to 20 to batteries, affect run times. Calculating the 4. Align contacts of bulb with terminals in Amps will not yield five hours discharge time exact run time is not precise due to all the fixture base.
  • Page 140 8 — electRical systems - House vacationeR diesel 2006 To Replace a Bulb: 1. Remove the light cover either by hand and pulling it off, or carefully with a thin, flat blade like a butter knife. Take care as not to scratch the wood. 2. Two pins allow the light lens to pivot.
  • Page 141 Vacatoner Desel 2006 electrcal Systems - Chasss — Secton 9 chaSSIS electrIcal - IntroDuctIon ..138 Battery DISconnect ........138 Chassis............. 138 Battery - chaSSIS ........138 fuSe & cIrcuItS .......... 138 Front.Distribution.Panel......138 alternator ..........139 Alternator.Testing.Procedure....... 140 SteerIng column ........
  • Page 142: Chassis Electrical - Introduction

    2006 section 9 — electRical systems - cHassis WARNING chaSSIS electrIcal - IntroDuctIon Battery - chaSSIS When welding is involved for motorhome repair or modification, This section contains guidelines, procedures The chassis battery is designed to produce high only qualified, experienced technicians and information that will assist in understanding amperage necessary to start the engine. Maintain should weld on the chassis.
  • Page 143: Alternator

    2006 section 9 — electRical systems - cHassis Using a fuse of a different rating will defeat alternator the circuit protection provided by the fuse, which could result in damage to the motorhome The alternator electrical system. If a fuse has been replaced is designed for and it “BLOWS” repeatedly, that may be an output through indication that a fault exists or an electronic the engine component has failed. It is recommended that operating range. the motorhome be taken to a qualified...
  • Page 144: Alternator.testing.procedure

    2006 section 9 — electRical systems - cHassis NOTE DO NOT disconnect the battery, or and hold the lever down. Push down or  The alternator is not designed to charge battery wire, from the alternator with the pull up on the steering wheel until the the house batteries from a complete engine running as this can damage the wheel is in place. Release the lever and discharge to a full state of charge.
  • Page 145: Dash

    2006 section 9 — electRical systems - cHassis Hazard Flasher Button: Located on the Overheating may be a Result of any of 7. MILEAGE/TRIP RESET BUTTON: Steering Column. the Following Conditions: Used to toggle between the odometer Pull out on flasher button to turn four Low coolant level.
  • Page 146: Switches

    2006 section 9 — electRical systems - cHassis 6. CRUISE: Indicates when cruise 11. HEADLIGHT BEAM: High beams the function and press the bottom to stop the control is activated. when illuminated. function. Following is a list of switches used and their functions. 7. WARNING: Out of range conditions 12. WAIT TO START: Monitors the air exist within the engine protection intake heater at engine start up.
  • Page 147: Controls

    2006 section 9 — electRical systems - cHassis NOTE Passenger Console GEN SET: The generator automatically Some municipalities have ordinances initiates a preheat cycle when the switch banning the use of the exhaust brake. STEP LIGHT: Provides power to the exterior is pressed to START. The preheat cycle Be sure to check road signs in densely is indicated by the light on the switch amber step light.
  • Page 148: Air Conditioner & Heater Controls

    2006 section 9 — electRical systems - cHassis NOTE MAX A/C - Recirculated air is aIr conDItIoner & heater controlS If the headlights are left ON and drawn from the passenger area the ignition turned OFF a warning and discharged through the dash The system is designed to only provide bell sounds alerting the driver that louvers.
  • Page 149: Diagnostic Plug Location

    2006 section 9 — electRical systems - cHassis Heat and Defrost Operation: slower blower speed until normal engine the A/C system. The air conditioning compressor operates operating temperature is obtained. The air system on the motorhome must  in all modes except VENT, FLOOR and OFF have adequate pressure to operate the Summer Use: to dehumidify the air. Rotate the temperature vacuum generator or damper doors will control switch to set discharge air temperature.
  • Page 150: Engine "No Start" Flow Chart

    2006 section 9 — electRical systems - cHassis engIne “no Start” floW chart...
  • Page 151: Tail Light Bulb Replacement

    2006 section 9 — electRical systems - cHassis Insert two flat head screwdrivers into the taIl lIght BulB replacement  “short side” of the light lens and gently pry the lens from the frame. Use the two The light lens assembly is removable giving points marked “A” as pry points. access to either replace a defective bulb or install a new light lens assembly.
  • Page 152 2006 section 9 — electRical systems - cHassis NoteS...
  • Page 153 Vacatoner Desel 2006 Chasss Informaton — Secton 10 chaSSIS - IntroDuctIon ......150 engIne general InformatIon ....158 hyDraulIc SyStem ........170 Brake SyStemS ........... 150 Diagnostic.Fault.Codes........ 159 Hydraulic.Reservoir.(Power.Steering)..170 Hydraulic.Brakes......... 150 StartIng proceDure ........160 Hydraulic.Filter.(Power.Steering).
  • Page 154: Chassis - Introduction

    2006 section 10 — cHassis infoRmation Both are located in the rear curbside chaSSIS - IntroDuctIon Brake SyStemS compartment. Unscrew and lift off the Hydraulic Brakes black box to access the transmission This section contains information and Electronic Control Module. The chassis incorporates three separate braking instruction regarding various components of the 5.
  • Page 155: Maintenance

    2006 section 10 — cHassis infoRmation The design of the Booster doesn’t function properly in braking effect.  master cylinder power or back-up mode. Repair the When the exhaust brake activates, an electrical provides two separate booster and pump assembly. signal is sent from the engine ECM (electronic brake fluid systems Booster works only in the back up mode.
  • Page 156: Abs System (Anti-Lock Brakes)

    2006 section 10 — cHassis infoRmation motorhome is parked. Investigate any unusual aBS SyStem (antI-lock BrakeS) Alignment or loud noises that occur. Begin by checking Camber: the level of the hydraulic fluid. Traveling at The Hydraulic Antilock slow speeds over rough terrain may cause a...
  • Page 157: Lubrication.maintenance.safety

    2006 section 10 — cHassis infoRmation INFORMATION Toe-in: Occurs when the tire front distance is For more information, contact a Dana less than the tire rear distance. service representative at (419) 535-4500 Toe-out: Occurs when the tire front distance is or visit their website at www.dana.com. greater than the tire rear distance.
  • Page 158: Steering.column

    2006 section 10 — cHassis infoRmation 2. With finger, cover the rear air hole so Steering Column grease flows to the front seal. Apply the The intermediate steering shaft connects the specified grease at the grease fitting on steering wheel to the steering box. Service the the slip yoke.
  • Page 159: Steering.gear

    2006 section 10 — cHassis infoRmation a telescopic, mono tube unit filled with nitrogen travel. The control panel will not activate until Steering Gear gas and hydraulic oil. The result of the mixture the following safety features are in place.
  • Page 160: Prior.to.leveling

    2006 section 10 — cHassis infoRmation CAUTION LOW VOLTAGE – Indicates chassis Manual Leveling Operation:  Ensure potential jack contact points voltage is low. Follow the instructions in Prior to  are clear of obstructions or depressions ENGAGE PARK BRAKE – Indicates Leveling.
  • Page 161: Automatic.leveling

    2006 section 10 — cHassis infoRmation down and the park brake is released or INSPECTION Extend the jack position according to the  transmission placed in gear. Before moving the motorhome always indicator lamp. Example: If the indicator...
  • Page 162: Engine General Information

    2006 section 10 — cHassis infoRmation Drive-away Protection: Adding Fluid: The diesel engine in the motorhome controls With the jacks extended and the park brake If the leveling system makes unusual noise or engine speed by varying fuel supply only. No is released, a warning alarm will sound and the alarm sounds when driving around corners or throttle plates are used. An exhaust driven all LEDs will illuminate. The jacks will over bumpy roads, this indicates a low fluid level.
  • Page 163: Diagnostic.fault.codes

    2006 section 10 — cHassis infoRmation NOTE INFORMATION CHECK ENGINE - Indicates the The engine dataplate, located on the Refer to the OEM for additional engine requires maintenance or fluids. curbside front of the engine block, shows information concerning the operation, The motorhome should be serviced to specific facts about the Cummins engine.
  • Page 164: Starting Procedure

    2006 section 10 — cHassis infoRmation Each fault code will flash twice before to the START position and crank the Cold Weather advancing to the next code. engine. The electronic controls on the In sub-freezing or engine will automatically deliver the correct amount of fuel for the engine to extreme cold, engine StartIng proceDure start. oil becomes thick Normal Starting 7. Release the ignition switch to the ON and battery output is reduced.
  • Page 165: Engine Shutdown

    2006 section 10 — cHassis infoRmation or oil with adequate low temperature properties the fluid levels are correct. Follow the normal used for Arctic operations where the engine starting procedures. If the oil pressure gauge cannot be kept warm when shut down, will aid does not register within 15 seconds, shut off the in starting.
  • Page 166 2006 section 10 — cHassis infoRmation Coolant Types: The charge air cooler cools intake air for engine is stopped, and coolant is drawn back in • Coolant must meet ASTM 04985 the engine after it has passed through the the radiator by a vacuum. Thus, the radiator is (6M6038M) specifications. turbocharger. This is necessary due to the heat kept filled with coolant to the desired level at all generated as the intake air is pressurized, and times, resulting in increased cooling efficiency.
  • Page 167: Coolant.system.maintenance

    2006 section 10 — cHassis infoRmation shedding from a rotten hose. Replace any hose charge aIr cooler Coolant System Maintenance found to be cracked, swollen or damaged. Inspect other components of the cooling Connections should be inspected periodically The diesel engine and hose clamps tightened. system when performing maintenance. Have...
  • Page 168: Transmission

    2006 section 10 — cHassis infoRmation Before air enters the intake manifold, the CAC selection in all drive ranges and automatic The window displays gear selection, various cools the intake air temperature to the engine engagement of the torque converter lockup transmission modes, oil level and transmission manufacturer specifications. Lowered intake air clutch. fault codes. temperatures reduce exhaust emissions, improve The electronic control system has five major fuel economy and increase horsepower. The...
  • Page 169: Shift.inhibits

    2006 section 10 — cHassis infoRmation NOTE When the Exhaust brake is used, the Shift Inhibits  For some problems, diagnostic codes display changes to a default reading of 2, may be registered without the ECU 3 or 4. This default is pre-selected at the Shift inhibits falls within certain categories.
  • Page 170: Periodic.inspections

    2006 section 10 — cHassis infoRmation A Park Pawl is used with the transmission 1. The shifting feels odd. The transmission fill/dipstick are located at the which effectively grounds the output shaft 2. The transmission leaks fluid. rear near the radiator. An orange colored cap preventing rotation of the driveline.
  • Page 171: Fuel System

    2006 section 10 — cHassis infoRmation Cold Check: Hot Check: commercial winter blend diesel fuels are the The concept of a cold check is to determine Because the fluid level rises as the most common commercially available and  adequate fluid level for safe operating until hot temperature increases, the fluid must be recommended for use. The use of #2 diesel fuel check can be performed.
  • Page 172: Fuel.tank

    2006 section 10 — cHassis infoRmation The “Centroid” sender has four 2 - Full Adjustment (FULL): The full Fuel Tank connections: adjustment can be used to correct for 1 & 2 - Positive (POS) and Negative slight differences between fuel meters. The diesel fuel tank is made of steel. Pick-...
  • Page 173: Fuel.lines.&.Hoses

    2006 section 10 — cHassis infoRmation fasteners frequently and tighten or replace NOTE C. Contact Centroid: Probably 90% of them as necessary. Always carry an extra filter as one tank the return Centroid tests work okay full of excessively contaminated diesel on the bench. If you have incorrect fuel can plug a filter.
  • Page 174: Hydraulic System

    2006 section 10 — cHassis infoRmation 6. Install the filter onto the housing. side of the dipstick. It should be in the Hydraulic Reservoir (Power Steering) Tighten an additional three-quarter to area of “HOT” on the dipstick. This is the normal range. Do not exceed the...
  • Page 175: Air Filter

    2006 section 10 — cHassis infoRmation 4. After replacing the filter assembly, normal wear particles from the axle components, reverse the process to re-assemble the but will cause faster than normal wear of reservoir. the axle components if allowed to circulate 5. When attaching the cover plate in through the lubricant. It is recommended that the rubber cover seal, check for any the magnetic plugs be tested, if not replaced, at damage. each lubricant change. These plugs should have 090317 sufficient magnetic strength to pick up a 1.5...
  • Page 176 2006 section 10 — cHassis infoRmation NOTE 3. If new grease does not purge at the While checking the lube level, also seals go around to the other side and check the housing breathers. Clean the grease at those fittings, then loosen the breathers if dirty or replace them if bearing cap bolts and re-grease until damaged.
  • Page 177: U-Joint Angles, Phasing & Drive Shaft Balance

    2006 section 10 — cHassis infoRmation WARNING components. If there are no alignment marks, economically, the drive shaft must be carefully Rotating shafts can be dangerous. they should be added before disassembly of the checked and lubricated at regular intervals. Rotating shafts can snag clothes, skin, shaft to assure proper reassembly.
  • Page 178 2006 section 10 — cHassis infoRmation Proper Lubricant Waste Disposal: in component failure. lubricating consistencies, properties and When performing service maintenance on maximum operating temperatures. Most the engine, transmission or rear axle, waste containers list the base compound and maximum Grease ratings and their base compounds are fluids and filters should be properly disposed of operating temperature usually listed as melting especially important when selecting a lubricant or recycled.
  • Page 179 2006 section 10 — cHassis infoRmation Greasing: To apply grease: Thoroughly clean all Zerk grease fittings Clean the grease fitting. Initially operate  before applying new lubricant. Keep paper grease gun until new lubricant discharges towels or disposable rags handy when greasing. from nozzle, then wipe nozzle clean to...
  • Page 180: Lubrication Charts

    2006 section 10 — cHassis infoRmation luBrIcatIon chartS 070166i 070167m...
  • Page 181 2006 section 10 — cHassis infoRmation component: action: When: code lubrication code chart: engine Oil Dipstick keep to Full Mark Before Each Trip + Daily Enroute *Cl-4 u-Joints located inside coach under steering cover. use chassis lubricant. 1 a. engine Oil Fill...
  • Page 182: Specifications Charts

    2006 section 10 — cHassis infoRmation SpecIfIcatIonS chartS Chassis Fluid Capacities Tank Capacities chassis liqUid capaciTies isB-ad Tank Capacities (approx. Gallons) all Models engine Oil 17 Qts. Grey water 60 gallons Transmission Oil (initial amount) 14.8 Qts. Black water...
  • Page 183: Battery Specification Charts

    2006 section 10 — cHassis infoRmation Battery SpecIfIcatIon chartS application ah (20 hr) cca† rc (25a @ 80° f) Minutes 12 volt Chassis* Group 31p - MHD (2 each) 6 volt Domestic** u2200 (4 75 Amp @ 80° F = 230 Min.
  • Page 184: Maintenance Records

    2006 section 10 — cHassis infoRmation maIntenance recorDS After scheduled services are performed, record the date, odometer reading and who performed the service in the boxes provided after the maintenance interval. Any additional information from “Owner Checks and Services” or “Periodic Maintenance” can be added on the following record pages. In addition, retain receipts. The owner information portfolio is a convenient place to store them.
  • Page 185 2006 section 10 — cHassis infoRmation BaTTery reCOrD servICe Make TyPe DaTe InsTalleD rePaIrs DaTe rePlaCeD MOnTHs MIles TIre reCOrD servICe DaTe DaTe Make TyPe rePaIrs InsTalleD rePlaCeD MOnTHs MIles...
  • Page 186 2006 section 10 — cHassis infoRmation BaTTery reCOrD servICe Make TyPe DaTe InsTalleD rePaIrs DaTe rePlaCeD MOnTHs MIles TIre reCOrD servICe DaTe DaTe Make TyPe rePaIrs InsTalleD rePlaCeD MOnTHs MIles...
  • Page 187 2006 section 10 — cHassis infoRmation Technical PublicaTions Manager: ILLuSTRATIONS: ONLINE TOuRS vance Buell kelly stroble, aaron Graham, Dustin Hutchcraft www.monaco-online.com/tours/ OPERATIONS PRINTING Vacationer Diesel 2006 ~ Technical Writer Technical Writers Holiday Graphics - In Thomas Joachim william Birch - Or Vacationer Diesel 2006 ~ Layout Design &...
  • Page 189 Vacatoner Desel 2006 Index Battery Disconnect ........125 Cooktop With Oven (Optional) ....75 House ............125 Lighting the Oven ........75 Battery Specification Charts ......179 Lighting Top Burners ........75 ABS System (Anti-lock Brake) ....152 Booth Dinette ..........93 Coolant System ..........161 Air Conditioner & Heater Controls ..144 Bed Conversion .........93 Alternator ............139 Coolant System Maintenance ....163 Brake - Exhaust Brake .......151...
  • Page 190 2006 Driving & Safety ...........12 Furnace ............77 Waxing ............46 Familiarize Yourself ........12 Wheels - Coated Aluminum ......48 If the Furnace Fails to Light ......78 Exterior Maintenance ........49 Inspections ..........12 Operation ...........77 Fiberglass ..........49 Mirror Adjust ..........12 Using the Furnace ........78 Fuse &...
  • Page 191 Retracting Leveling Jacks .......157 Sofa ..............92 Mold & Mildew ..........60 Lights ............135 Owner’s Manual Survey: Air Mattress (Optional) ......93 Directional Map Lights ......135 Vacationer Diesel 2006 ........7 Hide-A-Bed (Optional) ......93 Interior Incandescent .......135 Jack Knife Sleeper Sofa ......92 Limited Warranty Transfer Application/ P,Q,R Specifications Charts ........178 Change of Owner Information ......9...
  • Page 192 2006 W,X,Y,Z Tail Light Bulb Replacement .....147 Window Treatments ........59 To Reinstall the Light Lens Assembly ..147 Day/Night Shades ........60 To Replace a Light Bulb ......147 Mini-Blinds ..........59 Wall Coverings ..........56 Tires ..............27 Winterization ..........108 Wall Thermostat ..........75 Warranty Information File ......4 Air Pressure Checklist .......30...

Table of Contents