Advertisement
Available languages
Available languages
Option 2, Power s upply cordmethod:
NOTE: Amating, t hreeprong, g round-type wanreceptacb
is required ina cabinet next t o thedishwasher opening.
1. DrHH a 1ol/2"
(3.8 cm)hobin
optionalpreferred
thecabinet r ear
locations l ocations
or side, P referred [ii_i
andoptional
......
bcafions are
shown.
2. VVood cabinet:
Sand hobuntil
smootL
Metai cabinet: Cover hone with grommet
(Part No.
302797) inciuded
with power suppiy
cord kit.
mnstall
the
water
line
NeJpfuJTip:
Routing the water Hne through
the Heft side
of cabinet opening
will make water connection
easier.
Drill a minimum
1/2" {1.3 cm) hole in the cabinet side,
rear or floor. Preferred
and optional
locations
are
shown.
preferred
locations
optional
locations
2.
Measure
overall
length
of copper
tubing
required.
3.
Attach
copper
tubing
to the water
line with
a
manual
shutoff
valve.
copper
tubing
4.
Slowly
feed
copper
tubing
through
hole
in
cabinet.
Copper
tubing
will
bend
and kink easily,
so be
gentle.The
copper
tubing
should
be far enough
into the
cabinet
opening
to connect
it to dishwasher
inlet
on the
front
left of the dishwasher.
5.
Turn
water
shutoff
valve
to "ON"
position.
Flush
water
into
a shallow
pan to get rid of particles
that
may
clog
the inlet valve.
6. Turn shutoff
valve to "OFF" position.
mnstaH the drain
hose
IMPORTANT: Always
use a new drain hose.
1, Drill a 1-1/2" (3,8 cm)
diameter
hole in
cabinet wall or floor on
the side of the opening
closest to the sink
2.
Connect
drain
hose to waste
tee or waste
disposer
using
one of the following
methods:
o Option
1, Waste
disposer-with
air gap
o Option
2, No waste
disposer-
with
air gap
o Option
3, Waste
disposer
- no air gap .×
Option
4, No waste
disposer
- no air gap _
_an air gap is recommended
HeJpfu_Tip:To
reduce the vibration
of the hose, keep
the hose away from the floor and the edge of the hole
where it passes through
the cabinet.
Option
1, Waste
disposer
= with
air gap:
1.
Remove
the disposer
knockout
plug.
Cut end of drain
hose
if needed
(do not cut ribbed
section}.
2.
Attach
drain
hose
to air gap with
large
spring-type
clamp.
If the drain
hose was
cut, use a 1-1/2"
to 2"
(3.8 to 5 cm) screw-type
clamp x.
3.
Use a rubber
hose
connector
_ with
spring
or screw-
type
chmps
x to connect
air gap to disposer
inlet.
This connection
must
be before
the drain
trap
and at
least
20" (50.8 cm) above
the floor
where
dishwasher
will
be installed.
drain hose -
cut here if needed
rubber hose
connector
gap
spring-type
clamp
"" drain
hose
drain trap
E
4.
Insert
drain
hose
|
drain hose
through
hole cut in
cabinet
to the front
center
of opening
where
drain
connection
will
be
/
...................
made.
Parts available
from local plumbing
supply stores
Advertisement
