Advertisement
Available languages
Available languages
4. Check t hatwaterlineis ontheleftsideofopening and
drainhoseisnearthecenter o ftheholeinthecabinet.
5.
Slowly
move
dishwasher
completely
into
cabinet
opening.
Do not kink
or pinch
copper
tubing,
drain
hose,
power
supply
cord
or direct
wire
between
dishwasher
and cabinet.
HeipfuJTip:
Once the dishwasher
is in position,
you
may
have to support
the front
of the dishwasher
by
raising,
lowering
or shimming
front
feet.
6.
Remove
cardboard
from
under
dishwasher,
NOTE:
it is all right
if dishwasher
fits tightly
into
cabinet
opening.
Do not remove
insulation
blanket
--the
blanket
reduces
the sound
level.
Check door spring
tension
1.
With
another
person
holding
the dishwasher
to prevent
it from
tipping,
open
and close
the door
a few times,
if
the door
closes
or falls
open
under
its own
weight,
the
door
tension
will
need
to be adjusted.
2.
To adjust
the door
spring
tension,
unhook
the spring
from
the rear
leg of dishwasher.
3.
With
a 5/16"
nut driver
or hex socket,
remove
the screw
from
the tensioner.
4.
The screw
can be put into
one of three
holes
D,
F_Jl,D
in front
leg of dishwasher.
If the door
closes
by itself,
move
the tensioner
to a higher
number
hole
and
replace
screw.
When
door
is unlatched,
if it opens
by
itself,
move
tensioner
to a lower
numbered
hole
and
replace
screw.
5.
Re-attach
door
spring
to rear
leg.Tensioners
on both
sides
of dishwasher
should
be secured
at same
holes.
spring
screw
LeveU the dishwasher
Align
front
of dishwasher
door
panel
with
cabinet
doors.You
may
need
to adjust
alignment
to be even
with
your
cabinets.
He[pfu[Tip:
Prop up one side of frame
to hold
dishwasher
up off floor
when
adjusting
front
legs,
2.
Check that
leveling
legs are firmly
against
the floor.
3.
Close
and latch the door,
and place
level
against
the
front
panel.
Check that
dishwasher
is plumb,
if needed,
adjust
leveling
leg or add shims
under
rear
wheel
until
dishwasher
is plumb.
4.
Repeat
for other
side of dishwasher,
NOTE:
Shims
must
be securely
attached
to floor
to prevent
their
movement
when
the dishwasher
is operated,
5.
Place
level
against
top front
opening
of tub,
Check that
dishwasher
is level
from
side to
side,
If dishwasher
is not level,
adjust
front
legs up or down
until
dishwasher
is level,
Make
EJectricaJ
Connection
Check "Electrical
requirements"
section.
You
need
to:
o have
the correct
electrical
supply
and recommended
grounding
method.
if you
are:
o direct
wiring,
use Option
1
o using
a power
supply
cord,
use Option
2
Option
1, Direct wire method
1. Route direct wire so that it does not touch dishwasher
motor
or lower part of dishwasher
tub,
2. Pull direct wire through
hole in terminal
box,
Helpful
Tip:
o Select
the proper
size twist-on
connectors
to connect
your
household
__
wiring
to 16-gauge
dishwasher
wiring,
o Insert
wire
ends
into
twist-on
connector,
Do not pre-twist
bare wire,
oTwist
connector,
o Gently
tug on wires
to be sure
both
are __
secured,
12
Advertisement
