Viking K-1900-3 Technical Practice page 5

E. Programming Examples
These examples would be entered after accessing programming as shown in section A.
Programming the K-1900-3...
1. ...to dial 555-1234 when a "1" is entered at the entrance phone
2. ...to dial a 9 and pause 3 seconds prior to dialing all numbers
3. ...to activate the door strike/magnetic lock when the tenant dials a "66"
4. ...to set keyless entry code for tenant 3 to "9876" with phone number 555-1234
5. ...to set a keyless entry code for tenant 4 to "9876" without a phone number
6. ...to delete the keyless entry code and phone number for tenant 5
7. ...to set a maximum call time of 10 minutes
8. ...to set the master keyless entry code to "123456"
F. Programmable Maximum Call Time
The K-1900-3 can be programmed to limit the call time on the entry phone. The maximum call time is programmable
from "00" (no maximum call time) to "99" (99 minutes) and is factory set to "02" (2 minutes) (see Programming, sec-
tion D). When the call timer is enabled (programmed to "01-99"), if a call exceeds the programmed time, both phones
are provided with three beeps then disconnected, indicating the termination of the call. This limits unnecessary and
lengthy conversations. When the call timer is disabled (programmed to "00"), there is no limit to the length of calls from
the entry phone. Only a CPC disconnect signal from the telephone line, or hanging up the entry phone will disconnect
the call.
G. Built-In Toll Restriction
The K-1900-3 features built-in toll restriction. When the K-1900-3 is in the Apartment Dialer Mode (factory setting),
the unit will disconnect when it detects any Touch Tone or pulse dialing generated by the entry phone, after speed dial-
ing has been completed. With the K-1900-3 in the Multi-Number Dialer Mode, the unit will disconnect when it detects
any flashes or pulse dialing generated by the phone after speed dialing has been completed.
O p e r a t i o n
O p e r a t i o n
A. Apartment Dialer Mode
When a visitor accesses the entry phone, simulated dial tone is heard. After the visitor enters the appropriate one to
three digit tenant number (equal to the memory location in programming), the K-1900-3 dials the tenant's phone num-
ber and bridges the phone line to the entry phone. If an unprogrammed tenant number is entered, a simulated fast busy
signal will be heard on the entry phone. When the tenant confirms the visitors identity, a one or two digit relay activa-
tion code may be entered from the tenant's phone. Two beeps will indicate that a valid activation code has been
entered. A buzzing sound is then heard on the entry phone to indicate the door strike has been activated. If an incor-
rect relay activation code is entered, the unit will disconnect. A simulated fast busy signal will also be returned to the
entry phone if the telephone line has become disconnected. A tenant may use their personal keyless entry code to let
themselves in by taking the entry phone off-hook and entering a "#" followed by their (4 - 6 digit) personal keyless entry
code. Note: To avoid busy signals on the entry phone, call waiting is recommended on each tenant's phone line.
B. Multi-Number Dialer Mode
This mode is useful when using the K-1900-3 in applications other than apartment/multi-tenant entry, such as Kiosks or
any other user selectable speed dialing application when 150 phone numbers or less are required. An off-hook on the
phone port will return simulated dial tone. The user can then enter their one to three digit speed dial memory location.
The K-1900-3 speed dials the phone number programmed in that memory location then bridges the phone to the line.
The user is now free to dial any Touch Tone numbers required to steer through automated attendants, etc. If the user
attempts to pulse dial or flash the line for fresh dial tone (to make a toll call), the K-1900-3 will restrict the call by switch-
ing the phone back to artificial talk battery with a simulated busy signal. Note: If this phone is to receive in-bound calls,
select the Ring Thru Mode (see Operation section C). Also, keyless entry codes work, but there is no relay activation
from the tenant's phone.
(factory setting)
(relay activation codes ignored after dialing)
Enter Digits
5551234 #001
9 ##2
66 ##4
,
5551234# 9876 #003
,
# 9876 #004
#005
10 ##6
,
# 123456 #150