Page 1
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JH 6P72 TV Service...
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JH 6P72 TV Service...
EN 1 MQC2.OA LA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: VGA:Video RGB In 1.1 Technical Specifications 1.2 Connections 1.3 Chassis Overview Note: Figures below can deviate slightly from the actual situation, due to the different set executions.
Page 4
Technical Specifications, Connections, and Chassis Overview EN 2 MQC2.OA LA 1.2.2 Right I/O Connections 1.2.3 Left I/O Connections RF_Analog 75ohm Unbalance F-type connector RF_Digital 75ohm Unbalance F-type connector AV1-S1/AV2-S2: S-Video 1Fh Y/C-In Line-out -Ground Y Audio R 0.5 Vrms/10Kohm -Ground C Audio L 0.5 Vrms/10Kohm -Video Y...
EN 3 MQC2.OA LA Safety Instructions, Warnings, and Notes 2. Safety Instructions, Warnings, and Notes 2.1 Safety Instructions • Where necessary, measure the waveforms and voltages with ( ) and without ( ) aerial signal. Measure the Safety regulations require that during a repair: voltages in the power supply section both in normal •...
If this is not • Use only lead-free soldering tin Philips SAC305 with order possible, try to align the (LF)BGA with any board markers. code 0622 149 00106. If lead-free solder paste is required,...
Mechanical Instructions EN 5 MQC2.OA LA 4. Mechanical Instructions Index of this chapter: 4.1 Cable Dressing 4.2 Foam Bars 4.3 Panel/PCBA Removal 4.4 Disassemblyt and Re-assembly 4.1 Cable Dressing 4.2 Service Positions 4.2.2 Stands 4.2.1 Foam Bars The foam bars (order code 3122 785 90580 for two pieces) can Figure 4-3 Stands be used for all types and sizes of Flat TVs.
Page 8
EN 6 MQC2.OA LA Mechanical Instructions 4.3 Panel/PCBA removal 4.3.4 Main Board & Translation Board 4.3.1 IO/Sub IO 1. Disconnect all cable from Base unit 2. Remove the fixation screws 3. Take out the Translation/B & Main Board 4.3.5 AD6 CPU Board & Translation Board 1.
Page 9
EN 7 MQC2.OA LA Mechanical Instructions Disassembly process 4.4.1 4.4.2...
Page 10
Mechanical Instructions EN 8 MQC2.OA LA 4.4.3 4.4.4...
Page 11
Mechanical Instructions EN 9 MQC2.OA LA 4.4.5 4.4.6...
Page 12
Mechanical Instructions EN 10 MQC2.OA LA 4.4.7 4.4.8...
Page 13
Mechanical Instructions EN 11 MQC2.OA LA 4.4.9 4.4.10...
Page 14
Mechanical Instructions EN 12 MQC2.OA LA 4.4.11 4.4.12...
Page 15
Mechanical Instructions EN 13 MQC2.OA LA 4.4.13 4.4.14...
Page 16
Mechanical Instructions EN 14 MQC2.OA LA 4.4.15 4.4.16...
Page 17
Mechanical Instructions EN 15 MQC2.OA LA 4.4.17 4.4.18 Re-assembly To re-assemble the LCD panel, execute all processes in reverse order. Note: .While re-assemble, make sure that all are placed and And connected in their original position. See figure “Cable dressing” .Pay special attention not to damage the EMC foams at the SSB shielding.
Service mode, Fault Finding EN 16 MQC2.OA LA 5 Service mode and Fault Finding Index if this chapter: Setup 5.1 Service Modes for ATV 1. Off TV Power 5.2 Service Modes for DTV 5.3 Fault Finding 2. Process Pixlworks program 3.
Page 19
EN 17 MQC2.OA LA Service mode, Fault Finding Setup...
Page 20
EN 18 MQC2.OA LA Service mode, Fault Finding...
Page 21
Service mode, Fault Finding EN 19 MQC2.OA LA 5.3 Fault Finding Purpose To find the fault How to find fault...
Page 22
EN 20 MQC2.OA LA Service mode, Fault Finding Power cable Check Power cable Plug-in? Replace P/B or P/B to M/B LED bright? Power cable LCD panel can Replace M/B Display? LCD panel can Replace I/V to power cable Display? or LVDS cable TV source can Replace I/O board Display?
Page 23
EN 21 MQC2.OA LA Service mode, Fault Finding DVBT/ATSC source Replace DVBT/ATSC board can display Inverter power cable Change inverter power cable Plug in? LCD back light Replace Power board Bright? LCD back light Bright? Replace LCD Inverter board LCD back light Replace M/B Bright?
Page 24
Service mode, Fault Finding EN 22 MQC2.OA LA Remote control have Change battery Battery? IR board cable Check IR/B cable or replace Plug in? IR/B cable Press remote menu key Replace IR/B OSD can display? Press remote menu key Replace M/B OSD can display?
Page 25
EN 23 MQC2.OA LA Service mode, Fault Finding Key board cable Check K/B cable or replace plug in K/B cable Press Menu key Replace K/B cable Check function? Press Menu key Replace K/B cable Check function?
Page 26
EN 24 MQC2.OA LA Service mode, Fault Finding Check RF cable or replace RF cable RF cable Plug in? CVBS1 can’t Replace Tuner board display Replace I/O board Replace M/B RF can display Replace I/O board...
Page 27
EN 25 MQC2.OA LA Service mode, Fault Finding Component cable Check component cable or Plug in? Replace component cable Replace I/O board Component can Replace M/B Display?
Page 28
EN 26 MQC2.OA LA Service mode, Fault Finding S-video cable Check S-video cable or replace Plug in? S-video cable Replace I/O board S-video can Replace M/B display...
Page 29
EN 27 MQC2.OA LA Service mode, Fault Finding Check CVBS cable or replace CVBS cable CVBS cable Plug in? Replace I/O board CVBS can Replace M/B display...
Page 30
Service mode, Fault Finding EN 28 MQC2.OA LA Check Audio R/L cable or Audio R/L cable Replace Audio R/L cable Plug in? Check video cable or replace Video can display? Video cable Mute turn-off,volume=30 Earphone remove Check speaker cable or replace Speaker R/L cable Speaker cable Plug in?
Page 31
EN 29 MQC2.OA LA Service mode, Fault Finding Check or replace DVBT/ATSC Check DVBT/ATSC power Power cable Cable plug in? Replace DVBT/ATSC board Replace M/B DVBT/ATSC can display...
Page 32
EN 30 MQC2.OA LA Service mode, Fault Finding Check VGA cable or replace VGA cable plug in? VGA cable Read EDID data EDID data normal? Write EDID data Replace M/B VGA can display?
Page 33
EN 31 MQC2.OA LA Service mode, Fault Finding Check HDMI cable or replace HDMI cable plug in? HDMI cable Read EDID data EDID data normal? Write EDID data HDMI can display? Replace M/B...
Page 34
EN 32 MQC2.OA LA Service mode, Fault Finding Check HDMI cable or replace HDMI cable plug in? HDMI cable Read EDID data EDID data normal? Write EDID data Mute turn-off,Volume – 30 Check HDMI cable or DVD player Earphone remove Or replace HDMI cable PC volume setting to On Replace M/B...
Page 35
EN 33 MQC2.OA LA Service mode, Fault Finding Check line in cable or replace Line in cable plug in? Line in cable Mute turn-off,Volume – 30 Earphone remove PC volume setting to On Check Video cable or PC or PC/DVI can display? Replace VGA/DVI cable Replace M/B PC/DVI sound normal?
Page 36
EN 34 MQC2.OA LA Service mode, Fault Finding Check component cable Component cable Or replace component cable Plug in? Mute turn-off,Volume – 30 Earphone remove Component source Check component cable Can display? Or replace component cable Component sound Replace I/O board Normal? Component sound Normal?
Page 37
EN 35 MQC2.OA LA Service mode, Fault Finding Check video and R-L cable or AV1/S-video/R-L Replace video or R-L cable Cable plug in? Mute turn-off,Volume – 30 Earphone remove AV1/S-video source Check video and R-L cable or Can display? Replace video or R-L cable AV1/S-video sound Replace I/O board normal?
Page 38
EN 36 MQC2.OA LA Service mode, Fault Finding DVBT/ATSC RF cable Check RF cable or replace RF Plug in? cable Mute turn-off,Volume – 30 Earphone remove DVBT/ATSC source Can display? DVBT/ATSC sound Replace D-Tuner/B normal? DVBT/ATSC sound Replace DVBT/ATSC normal? DVBT/ATSC sound Replace M/B normal?
Page 39
EN 37 MQC2.OA LA Service mode, Fault Finding Check LVDS cable or replace Check M/B to LCD panel LVDS cable LVDS cable plug in? Check LCD panel Replace LVDS cable Tcon board voltage Check LCD panel backlight Replace M/B LCD panel display Replace LVDS cable Normal? Replace LCD panel...
Page 54
EN 52 MQC2.OA LA R726 NC/0R3 Watchdog IC R735 NC/0R3 NC/MAX809T-2.63V R727 1,2 and 9,10 Short for PROJet NC/4.7K3 FB25 C242 PICVPP BEAD/3 NC/0.1u3 CPU SLAVE MODE CON4 RESET R221 30mA 4.7K3 TESTMODE NC/PH1S-205GB-10P-LUV R728 TRSTn NC/4.7K3 R222 C243 C244 Flash memory must check the pin define 3.3K3...
Page 69
Circuit Diagrams EN 67 MQC2.OA LA 3915X_CVBS 3915X_GREEN 20.25MHz FBM2125HM330 3915X_RED 3915X_BLUE R38 1MR3 SC10U10V SCD1UX Place guard trace R191 R192 R193 R194 +5VD H2 NC H1 HEADER_2x10(2.54) RST_CPU# 2 Rev.B: Change the UART MODRI S-UART_RX R177 NC DBG_RXD MODDCD routing of Download port S-UART_TX R178 NC...
Page 70
EN 68 MQC2.OA LA Circuit Diagrams 3V3_M EM ORY 3V3_M EM ORY GADR[0..15] AM29LV320DT90EF 16bit flash should be able to GADR2 work on 8bit mode GADR3 GCS-0 GADR4 GADR5 GOE- GDAT0 GADR6 GADR7 Flash speed can be 120nS GDAT1 GADR8 Package :TSOP48 GDAT10 4 GDAT2...
Page 78
EN 76 MQC2.OA LA Circuit Diagrams IO connector CVBS S-VIDEO1 S-VIDEO2 VIDEO SWITCH Analog Tuner AUDIO FOR AV1 & S-VIDEO1 AUDIO AUDIO FOR AV2 & S-VIDEO2 ANALOG TUNER (video &audio) COMPONENT1 Y CB CR VIDEO SWITCH COMPONENT2 AUDIO AUDIO FOR COMPONENT1 SWITCH AUDIO FOR COMPONENT2 DIGITAL...
Page 85
EN 83 MQC2.OA LA Circuit Diagrams IR board LED1 +5V_IR L-3WEGC 0.1u BEAD_120 R4 1K BEAD_120 PHOTO IR GREEN POWER ON 33R3F power POWER OFF 33R3F GREEN SCREW HOLE SCREW HOLE SCREW HOLE 0.1u SCREW HOLE SCREW HOLE SCREW HOLE SCREW HOLE 220P/NC Standby mode: Red...
Alignments EN 85 MQC2.OA LA 8. Alignments How to align white Balance Equipment HDMI input ,VGA input, SCART RGB input, YUV input Method: 1.Input VGA 1024*768 @60hz Pattern: white . Do auto calibration 2.Input YUV 720p pattern: SMTPE. Do auto calibration 3.Input YUV (Component 1) 720p pattern: SMTPE.
Page 88
EN 86 MQC2.OA LA Alignments Input HDMI signal 1024*768@60HZ Pattern: white balance(190/225) 1024*768@60HZ Pattern: Dark balance(60/225) Adjust Standard, Cold Warm R,G,B Gain R,G,B Bias...
Page 89
IC Data Sheet EN 87 MQC2.OA LA 9. IC Data Sheets...
Page 90
Spare Parts List EN 88 MQC2.OA LA 10. Spare Parts List TV set 996500043051 HH2T TRANSLATION/B ASSY 996500043049 HH7T M/B ASSY(TWN) 996500043050 AD6 CPU/B ASSY(FOR HH7T) DVB-T 996500043030 HH2 LCD BEZEL ASSY (PHILIP) 996500043032 HH6 KEYPAD/B ASSY(FOR HR2K) 996500043041 HH2T PCB-HOLDER ASSY 996500043034 HH6 IR/B ASSY(FOR HH2) 996500043035 HH2 STAND-SUB ASSY 996500043033 HH6 POWER-IR-LED ASSY...
Page 91
EN 89 MQC2.OA LA Spare Parts List Media Box HH2T TUNER MODULE(W/PACKING)(TWN)SKD HH2T HDMI/B ASSY(W/PACKING)(TWN)SKD REMOTE CONTROLLER HH2T(EURT47BTPHQT1)
Page 92
Revision list EN 90 MQC2.OA LA 11. Revision list Manual xxxx xxx xxxx.0 • First release.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JH 6P72 TV Service...
MQC3.0A LA EN 1 Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: VGA:Video 2fh RGB In 1.1 Technical Specifications 1.2 Connections 1.3 Chassis Overview Note: Figures below can deviate slightly from the actual situation, due to the different set executions.
Page 95
MQC3.0A LA Technical Specifications, Connections, and Chassis Overview 1.2.2 Right I/O Connections Aerial-In Audio Out -F-type 75ohm Level: 500 mVrms AV1-S1/AV2-S2: S-Video 1Fh Y/C-In Type: Stereo R/L Channels 1-Ground Y Impedance: Low Impedance 2-Ground C Interface: RCA Jack, R: Red color, L: White color 3-Video Y 1Vpp/75 ohm 4-Video C...
MQC3.0A LA EN 3 Safety Instructions, Warnings, and Notes 2. Safety Instructions, Warnings, and Notes 2.1 Safety Instructions • Where necessary, measure the waveforms and voltages with ( ) and without ( ) aerial signal. Measure the voltages in the power supply section both in normal operation ( ) and in stand-by ( ).
2.3.4 Lead Free Solder Avoid temperatures above 400°C, otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed. To Philips CE is going to produce lead-free sets (PBF) from avoid wear-out of tips, switch “off” unused equipment or 1.1.2005 onwards.
Mechanical Instructions MQC3.0A LA 4. Mechanical Instructions Index of this chapter: 4.1 Cable Dressing 4.2 Service Positions 4.3 ASSY/PCBA Removal 4.1 Cable Dressing 4.2 Service Positions 4.2.2 Stands 4.2.1 Foam Bars Figure 4-3 Stands The stands can be mounted with the back cover removed or still The foam bars (order code 3122 785 90580 for two pieces) can left on.
Page 99
EN 6 MQC3.0A LA Mechanical Instructions 4.3 Assy/Panel removal 4.3.4 Main Board 4.3.1 IO Box Warning: Disconnect the AC Power cord before you open the 1. Disconnect all cable from Base unit set. 2. Remove the fixation screws 1. Place the TV set upside down on a table top, using the foam 3.
Page 100
Instructions MQC3.0A LA 4.3.13 Tuner Assy Disassembly 1. Place the TV set down on the foam bars. Place Disassembly the bars at the edges of the set, so they will 1. Remove the 3 screws from Tuner box cover support the front frame and not only the glass plate! 2.
Service mode, Fault Finding EN 8 MQC3.OA LA 5 Service mode and Fault Finding Index if this chapter: Setup 5.1Service Modes 1. Off TV Power 5.1Fault Finding 2. Process Pixlworks program 3. Choose appcode.inf 5.1 Service Mode (update BIOS) 4. Check connection. Should be in serial 5.
Page 102
Service mode, Fault Finding EN 9 MQC3.0A LA 5.2 Fault Finding Purpose .To find the fault How to find fault...
Page 103
Service mode, Fault Finding EN 10 MQC3.0A LA...
Page 104
Service mode, Fault Finding EN 11 MQC3.0A LA...
Page 105
Service mode, Fault Finding EN 12 MQC3.0A LA...
Page 106
EN 13 Service mode, Fault Finding MQC3.0A LA...
Page 107
EN14 MQC3.0A LA Service mode, Fault Finding...
Page 108
EN15 MQC3.0A LA Service mode, Fault Finding...
Page 109
EN16 MQC3.0A LA Service mode, Fault Finding...
Page 110
EN17 MQC3.0A LA Service mode, Fault Finding...
Page 111
EN18 MQC3.0A LA Service mode, Fault Finding...
Page 112
EN19 MQC3.0A LA Service mode, Fault Finding...
Page 113
Service mode, Fault Finding EN20 MQC3.0A LA...
Page 114
EN21 MQC3.0A LA Service mode, Fault Finding...
Page 115
Service mode, Fault Finding EN22 MQC3.0A LA...
Page 116
EN23 MQC3.0A LA Service mode, Fault Finding...
Page 117
Service mode, Fault Finding EN24 MQC3.0A LA...
Page 118
EN25 MQC3.0A LA Service mode, Fault Finding...
Page 119
Service mode, Fault Finding EN26 MQC3.0A LA...
Page 120
EN27 MQC3.0A LA Service mode, Fault Finding EN 27...
EN77 MQC3.0A LA 8. Alignments Warm mode White Balance Purpose . To alignments color Tools Video Pattern Generator (Should be with YUV output ) RCA cable Setup 1. Connect YUV to TV set. 2. Enter Factory Mode (Hot-Key: Volume- & Channel+ & Power Key) Cool mode 3.
Page 171
EN 78 MQC3.0A LA IC Data Sheet 9. IC Data Sheets...
EN 79 MQC3.OA LA Space Parts List 10. Space Parts List TV set 996500043082 HH7T LCD BEZEL ASSY(PHILIPS) POWER SAFETY MYLAR HH2(FCHH2001,REV3B) SCREW T3*12-B(NI)EP RUBBER SQUARE HR7(GAHR7001,REV3A) 996500043084 SIDE BRACKET-R/L-AUO HH7(FBHH7007,REV3A) EPE BAG HH7(HAHH7003,3A)1230*800 996500043085 LCD(TFT) 37.02'' T370XW01 V.1(XGA-WIDE) EPE SHEET VWE6(HAVW6004,3A)800*500...
Page 173
Revision EN 80 MQC3.OA LA 11. Revision Manual xxxx xxx xxxx.0 • First release.