Related Manuals for iStartek VT100-L
Summary of Contents for iStartek VT100-L
- Page 1 File Name VT100-L User Manual Ver. Update 2022-02-28 Page 1 of 23 iStartek GPS Vehicle Tracker VT100-L User Manual V1.0 Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved...
-
Page 2: Table Of Contents
8.1 Power Cable Function Introduction ....................11 8.2 Device Installation ........................... 12 8.3 Analog Input Installation ........................13 8.4 Ultrasonic Fuel Sensor Installation ..................... 16 8.5 Speed Limiter Installation ........................21 Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... -
Page 3: Copyright And Disclaimer
This manual cannot be copied for any purpose, disseminated in any way without the written authorization of iStartek. iStartek shall not be liable for direct, indirect or all losses (including but not limited to economic losses, personal injuries, property and assets) caused by the use or inappropriate use of the product or documents. -
Page 4: Product Specification
VT100-L CN： LTE-FDD: B1/B3/B5/B8 LTE-TDD: B34/B38/B39/B40/B41 GSM: 900/1800MHz Standard version I/O: DCIN+GND+OUT1+IN2+SOS+MIC (8-wire) LTE/WCDMA/GSM Bands VT100-L EU： LTE-FDD: B1/B3/B5/B7/B8/B20 GSM: 900/1800MHz Standard version I/O: DCIN+GND+OUT1+IN2+SOS+MIC (8-wire) VT100-L SA： LTE-FDD: B1/B2/B3/B4/B5/B7/B8/B28/B66 Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... - Page 5 Nano SIM card 2 Digital inputs（Can be configured by software for high and low level trigger, Analog input. IN2 is set to ACC detection by default） 1 Output 1 Micro USB Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved...
-
Page 6: Products And Accessories
（Customizable, MOQ500pcs） 5. Products and accessories 5.1 Standard accessories Main Unit with 8 Wires Main Unit with 6 Wires Power Cable 5.2 Optional accessories 12V/24V Relay USB Cable Buzzer Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... -
Page 7: Product Appearance
SOS Button Ultrasonic Fuel Sensor Capactive Fuel Sensor Speed Limiter 5.3 Customizable accessories RFID Reader RFID Tag OBD Decoder Magnetic Card Reader 6. Product Appearance Front view of 8-wire device Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... - Page 8 File Name VT100-L User Manual Ver. Update 2022-02-28 Page 8 of 23 Front view of 6-wire device Back image Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved...
-
Page 9: Product Operation
7.1 Recharge When using VT100-L for the first time, please connect the tracker's red wire (positive) and black (ground wire) to a 12V or 24V power supply and charge for at least 2 hours to ensure sufficient power. After configuration and testing are completed, install it on the vehicle. -
Page 10: Parameter Configuration
7.5 Parameter configuration Download and install the USB driver《PL2303_Prolific_Driver》. After the device is turned on, connect the VT100-L to the computer via iStartek USB cable, run the "iStartek Parameter Editor_V1.6" configuration software and open the port to enter the parameter configuration state. -
Page 11: Product Installation
Ver. Update 2022-02-28 Page 11 of 23 For more SMS command functions and parameter configuration, please refer to "iStartek GPS tracker Communication Protocol V1.3" and "iStartek Parameter Editor User Manual V1.5". 8. Product Installation 8.1 Power Cable Function Introduction Color Function DC In (power input), connect to the positive pole of the car battery. -
Page 12: Device Installation
An external relay can be connected to remotely cut off the car's fuel/engine power supply, etc. Mic+ Brown External Microphone, used for listening. Mic- Blue 8.2 Device Installation ①．8-wire standard version of VT100-L wire connection： Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... -
Page 13: Analog Input Installation
The range of analog input AD1 and AD2 is 0-6.6V. Need to configure IN1 (white wire) or IN2 (orange wire) as AD INPUT, up to two fuel sensors (voltage output type sensors) can be connected, the wiring connection is as follows Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... - Page 14 After connected wires, can set the size of the fuel tank (length, width, height), data source (AD1/AD2), sensor type (capacitive fuel sensor or ultrasonic fuel sensor), liters of fuel stolen, fuel stolen time, low fuel alarm by Parameter Editor. Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved...
- Page 15 Example: Connect the GPS Tracker analog input to capactive fuel sensor, the yellow-green wire of the sensor are connected to the white wires (AD) of the VT100-L. When the fuel is empty, the sensor output voltage is 0V, when the fuel is full, the sensor output voltage is 5V Calculate the percentage of remaining fuel: Fuel percentage=(AD/5)*100%=(4.56/5)*100%=91.2%.
-
Page 16: Ultrasonic Fuel Sensor Installation
8.4.1 Connect ultrasonic fuel sensor to VT100-L AD Take the analog input of VT100-L connected to the fuel sensor as an example, the green wire of the sensor is connected to the IN1 white wire of VT100-L (Need to configure IN1 as AD1 by parameter editor) or the IN2 orange wire (Need to configure IN2 as AD2 by parameter editor) ①... - Page 17 Select "Ultrasonic Sensorr" and set the data source of the fuel tank (select RS232-1/2), the sensor type is ultrasonic fuel sensor (Ultrasonic(100cm)/(250cm)), the size of the fuel tank (length, width, height) these parameters, then the tracker can obtain the remaining oil value Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved...
- Page 18 After opening the APP of the ultrasonic fuel sensor and connecting the Bluetooth, click "Settings", then enter the password "52381", click "Read" first - modify the baud rate as "115200" - click "Modify" - power off and restart ultrasonic fuel sensor. Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved...
- Page 19 Set the fuel theft alarm to active when the fuel reduction exceeds 20 liters within 60 seconds; Set low fuel alarm to active when the fuel volume is less than 10 liters. Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved...
- Page 20 20 of 23 Configuration by SMS Command: Set fuel tank parameters through SMS commands 138, 139, 140, and 141, 142. For related parameter setting commands, please refer to "iStartek GPS tracker Communication Protocol V1.3". Send above parameters by SMS commands: Set fuel tank parameters, you can send commands: 0000,138,1,1000,500,1000 Description: 1 is the serial number of the fuel tank.
-
Page 21: Speed Limiter Installation
V Cut off the gas pedal signal wire of the car, and connect the GPS Tracker VT100-L and speed limiter as shown in the figure below. (Note: The color of the gas pedal signal wire of different car models may be different. The following figure is only an example, and subject to the actual vehicle signal line) Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. - Page 22 22 of 23 ．After the wires are connected, the speed limit value can be set through the parameter editor or SMS command: ．Parameter editor settings: set as shown in the figure below: Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved...
- Page 23 0000,212,1,1,22 Set to trigger output 1 after exceeding the set speed value If you have any other questions, please send an email to info@istartek.com, we are happy to serve you. Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved...
Need help?
Do you have a question about the VT100-L and is the answer not in the manual?
Questions and answers