Subscribe to Our Youtube Channel
Related Manuals for iStartek VT140
Summary of Contents for iStartek VT140
- Page 1 File Name VT140 User Manual Ver. Update 2021-01-12 Page 1 of 11 iStartek Vehicle GPS Tracker VT140 User Manual V1.0 Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved...
-
Page 2: Table Of Contents
8.3 Digital inputs installation ........................9 8.4 Analog Input Installation ........................10 8.5 Output Control Wire Installation ......................10 8.6 Temperature Sensor Installation ......................11 8.7 Ultrasonic Fuel Sensor Installation ..................... 11 Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... -
Page 3: Copyright And Disclaimer
This manual cannot be copied for any purpose, disseminated in any way without the written authorization of iStartek. iStartek shall not be liable for direct, indirect or all losses (including but not limited to economic losses, personal injuries, property and assets) caused by the use or inappropriate use of the product or documents. -
Page 4: Product Specification
4 Digital inputs（Can be configured as high and low level trigger mode） 2 Analog input（0~36V） 2 Outputs 1 1-wire 2 RS232 1 5V output wire 1 Micro USB 5. Products and accessories 5.1 Standard accessories Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... -
Page 5: Optional Accessories
File Name VT140 User Manual Ver. Update 2021-01-12 Page 5 of 11 Main Unit 5.2 Optional accessories Ultrasonic Fuel Sensor Capacitive Fuel Sensor 12V/24V Relay USB Cable Buzzer 6. Product Appearance Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... -
Page 6: Product Operation
Download and install the USB cable driver "PL2303_Prolific_Driver". After the device is turned on, connect the VT140 to the computer via a USB cable, run the "iStartek Parameter Editor_V1.00" configuration software and open the port to enter the parameter configuration state. -
Page 7: Track By Gps Tracking Platform
You can set the server IP, Port, and APN parameters through SMS commands SET PIP、 SET PPT、 SET SIP、 SET SPT、 SET APN and you can also use the iStartek Parameter Editor software to configure related parameters. For more SMS command functions and parameter configuration, please refer to "VT140 protocol V1.0" and "iStartek Parameter Editor User Manual". -
Page 8: Product Installation
Digital, can be connected to iButton and temperature sensor Black DC 5V output, available for temperature sensor and serial port accessories. Green RS232-1 RX White RS232-1 TX Green RS232-2 RX Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... -
Page 9: Power Connection
8.3 Digital inputs installation Input2 can be connected to the vehicle ignition to detect ignition status. Input1, input3 or Input4 can be connected to the car door to detect the state. Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... -
Page 10: Analog Input Installation
8.5 Output Control Wire Installation The output wire can be connected to an external relay to cut off fuel/electricity and control the vehicle. You can also connect the buzzer to alarm. Copyright Notice ©Shenzhen iStartek Technology Co., Ltd. All rights reserved... -
Page 11: Temperature Sensor Installation
The height measurement range of the ultrasonic fuel sensor is 0~100cm (0~250cm optional), and the corresponding voltage output range is 0~5V. VT140 analog input connect to the ultrasonic fuel sensor, the green wire of the ultrasonic sensor is connected to the AD1 blue wire of the VT200 or the AD2 pink wire.
Need help?
Do you have a question about the VT140 and is the answer not in the manual?
Questions and answers