Bosch 0 601 B44 000 Original Instructions Manual page 21

Table saw
Hole diameter
A) Measured at 20−25 °C with rechargeable battery ProCORE18V 12.0Ah.
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
Maximum workpiece dimensions: (see "Maximum workpiece dimensions", page 26)
Noise information
Noise emission values determined according to
EN 62841-3-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 81 dB(A); sound power level
94 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Items included
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Table saw with fitted saw blade (26) and riving knife (4)
– Angle guide (2)
– Parallel guide (5)
– Additional parallel guide (43)
– "Additional parallel guide" fastening set (44) (2 fastening
screws, 2 washers, 2 wing nuts)
– Protective cover (3)
– Hex key (10)
– Ring spanner (9) with slotted screwdriver tip
– Push stick (12)
– Table insert (25)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
Bosch Power Tools
GTS 18V-216
mm 30
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Extra tools required (not included in the
delivery):
– Cross-headed screwdriver
– Angle gauge
Fitting individual components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
– Turn the locking screws (34) as far as possible in the "Un-
lock" direction using the tip of the ring spanner (9) and
open the base grid (33) (see figure a).
Remove the packing material under the motor block.
The following tool elements are attached directly to the tool
housing: Push stick (12), ring spanner (9), hex key (10),
parallel guide (5), angle guide (2), extraction adapter (31),
additional parallel guide (43) with fastening set (44), pro-
tective cover (3).
– If you require one of these parts, remove it carefully from
its storage location.
Positioning the riving knife (see figures b1–b2)
Note: If necessary, clean all parts to be fitted before you po-
sition them.
– Turn the crank (15) clockwise as far as possible so that
the saw blade (26) is in the highest possible position
above the saw table.
– Release the clamping lever (36) clockwise until it points
upwards.
– Slide the riving knife (4) towards the clamping lever (36)
until it can be pulled upwards.
– Pull the riving knife all the way up until it is positioned ex-
actly over the centre of the saw blade.
– Allow both pins (37) to engage in the lower bore holes in
the riving knife and then retighten the clamping lever
(36).
The markings (35) on the clamp and clamping lever (36)
must be aligned as shown.
English | 21
GTS 18V-216
25,4
1 609 92A 714 | (01.09.2021)