Subscribe to Our Youtube Channel
Related Manuals for Sumake SAF-100R
Summary of Contents for Sumake SAF-100R
- Page 1 INSTRUCTION MANUAL SAF-100R ITEM NO.: AUTOMATIC SCREW DRIVING MODULE SAF-100R-I-23087A-YM...
-
Page 2: Table Of Contents
SAF-1000R Instruction Manual Table of contents Instruction ････････････････････････････････････ II. Item inspections ･･･････････････････････････････ III. Safety precautions ･･････････････････････････････ IV. Specification Exterior ･･････････････････････････････････････ Working environment ･････････････････････････････ Weight ･･････････････････････････････････････ V. Pre-job checking ･･･････････････････････････････ VI. Test run ･･････････････････････････････････････ VII. Operating steps･････････････････････････････････ VIII. Troubleshooting Stripping ･･････････････････････････････････････ Working fail･･････････････････････････････････････... -
Page 3: Saf-1000R
I. Instruction The SAF-100R Automatic Screw Driving Module is suitable to automatic production also saves the trouble of manually picking screws as practiced conventionally. Furthermore, the machine can feed the screw to screwdriver also screwing to work-piece automatically. The working stability characteristic can enhance productivity, reduce human cost. -
Page 4: Specification
Remove the power plug if the machine is to remain idle for a long period of time Do not use non-specified screws DO perform regular maintenance of the machine as scheduled Specification 1. Exterior ： 2. Working environment ： Model SAF-100R Working voltage sensor：DC24V electric screwdriver: AC 110V / 220V Working air pressure 5.5(±0.5)kg/cm =0.54(±0.05)MPa Working Humidity 10℃~ 40℃... -
Page 5: Weight
3. Weight： Model SAF-100R Approx. 4.5KG Weight (kg) V. Pre-job checking 1. Install each items correctly. 2. Confirm that all power connectors, signal joint and air joint are properly installed in place. 3. Confirm the input power is correct. 4. Confirm that each sensor and cushion are positioned. -
Page 6: Operating Steps
A﹒ Make cylinder to minimum limit position. B﹒ Move the whole set SAF-100R and ensure the BIT aim the screw hole of work-piece, also the sensor lamp must be light. (3) Feeding：please ensure the screw can fed to tip of jaw after connecting with screw feeder, and the screw shank need exceed jaw. -
Page 7: Working Fail
(3) The BIT is bent and can’t be accurately aligned to the screw position. ➢ Check if the BIT is bent. ➢ Change BIT. (4) The BIT is worn after working period of time. ➢ Check if the BIT is worn. ➢... -
Page 8: Automatic Screw Feeder Breakdown
5. Automatic screw feeder breakdown： ➢ Please refer to the screw feeder instruction manual. IX. Maintenance 1. Please clean the component regularly every week. 2. Check whether the BIT is worn, and replace it if necessary. ※The maintenance period should be shortened if the operation is frequent or the environment is bad. - Page 9 SNF-A1, SNF-A2, SNF-A3, SNF-A4, SNF-A8, SNF-A9, SNF-A10, SNF-A11, SNF-A12, SNF-A13, SF40TH, SF30A, SF30M, SF30T, SF40A, SF40T, SF501, SF501T, SF502, SF502T, SAF-100S, SAF-100G, SAF-100L, SAF-100R, SDA, SF-SERIES The object of the declaration described above is in conformity with the relevant union harmonization legislation: ...
- Page 12 NOTE www.SUMAKE.com www.AIRCOMPRESSOR.com.tw...
Need help?
Do you have a question about the SAF-100R and is the answer not in the manual?
Questions and answers