Table of Contents
Advertisement
Quick Links
1. Panel, back panel diagram and button description............................................. 1
1.1
Panel diagram............................................................................... 1
1.2
Backplane diagram....................................................................... 1
1.3
Electronic ruler (or magnetic ruler) pin signal................................2
1.4
Button description......................................................................... 2
2 Basic Operation Instructions............................................................................... 3
2.1
Power on...................................................................................... 3
2.3
Absolute/relative coordinate switching......................................... 3
2.4
Metric/Imperial unit conversion.................................................... 4
2.5
Score............................................................................................4
2.6
Preset value................................................................................ 4
2.7
Outbound call operation...............................................................5
Three internal operation parameter function settings............................................6
3.1
3.2
Resolution settings...................................................................... 6
3.3
D/R mode setting.........................................................................7
3.4
Counting direction setting............................................................7
3.5
The last two digits of display settings.................................................. 8
3.6
Linear compensation setting........................................................8
3.7
Automatic setup...........................................................................9
3.8
Exit internal function settings........................................................ 9
Appendix A: Specifications...................................................................................10
www.ato.com
contents
sales@ato.com
Global Shipping
800-585-1519
Advertisement
Table of Contents
Related Manuals for ATO ATO-DR-WE100
Summary of Contents for ATO ATO-DR-WE100
-
Page 1: Table Of Contents
Entering the internal operation parameter function setting ..6 Resolution settings..............6 D/R mode setting.................7 Counting direction setting............7 The last two digits of display settings..........8 Linear compensation setting............8 Automatic setup................9 Exit internal function settings............9 Appendix A: Specifications...................10 www.ato.com sales@ato.com Global Shipping 800-585-1519... -
Page 2: Panel, Back Panel Diagram And Button Description
1.1 Panel diagram R/D indicator light window R/D LED Window WE-100 INCH ZERO PRESET Clear Score Preset/call out Relative/absolute coordinates English/Metric ZERO HALF Inch/mm Preset/Recall Inc/Abs 1.2 Backplane diagram EXTERN ZERO POWER LINEAR SCALE ver 2.13 www.ato.com sales@ato.com Global Shipping 800-585-1519... -
Page 3: Electronic Ruler (Or Magnetic Ruler) Pin Signal
The display value switches between metric/imperial system INCH Imperial/Metric units and increases the number by 1 when presetting the number. The preset/recall operation is a preset /call out PRESET confirmation key when setting the internal settings and preset numbers. ver 2.13 www.ato.com sales@ato.com Global Shipping 800-585-1519... -
Page 4: Basic Operation Instructions
Function introduction: The coordinates are between "ABS" (absolute coordinates) and "INC" (relative coordinates) switch between. Operation steps: according to key to complete the switch. Note: When the light is on, it means that the coordinate mode is "INC" (relative coordinates). ver 2.13 www.ato.com sales@ato.com Global Shipping 800-585-1519... -
Page 5: Metric/Imperial Unit Conversion
Function introduction: When the digital display is in normal display state, preset the display value of the current position. Example: Preset-125.455 Operation steps: PRESET 1) Press and hold For about 3 seconds, the window displays the current value of the electronic ruler (or magnetic ruler), ver 2.13 www.ato.com sales@ato.com Global Shipping 800-585-1519... -
Page 6: Outbound Call Operation
At this time The light above the key lights; Press PRESET key to cancel the call. 2) To prevent misoperation, you can press it again Note: Outbound calls can only be made in the INC state. 2.13 www.ato.com sales@ato.com Global Shipping 800-585-1519... -
Page 7: Three Internal Operation Parameter Function Settings
"UNIT 1" indicates that it has entered the internal function settings. 3.2 Resolution setting Set the electronic ruler (or magnetic ruler) resolution. Operation steps: 1) Enter the internal function settings; ZERO 2) Press key until the window displays "unit 1"; ver 2.13 www.ato.com sales@ato.com Global Shipping 800-585-1519... -
Page 8: D/R Mode Setting
(or magnetic ruler). 0 and 1 directions 3) Press the opposite direction, the specific direction will be determined during installation. The factory setting value is 0. ver 2.13 www.ato.com sales@ato.com Global Shipping 800-585-1519... -
Page 9: The Last Two Digits Of Display Settings
5) If the button was originally a positive number, the current value will become a negative number. On the contrary, if the button was originally a negative number, the current value will become a positive number. ver 2.13 www.ato.com sales@ato.com Global Shipping 800-585-1519... -
Page 10: Automatic Setup
Operation steps: ZERO 1) Press key until the window displays "QUIT". ZERO PRESET 2) Press to store the setting value and leave the internal function setting. (Press back to internal Key weight function settings) ver 2.13 www.ato.com sales@ato.com Global Shipping 800-585-1519... -
Page 11: Appendix A: Specifications
WE100 manual Appendix A: Specifications size: 104*77*35(mm) weight: 252.5g DC 7.5~9V Power <5W supply: Power consumption: Electronic interface: TTL ver 2.13 www.ato.com sales@ato.com Global Shipping 800-585-1519...
Need help?
Do you have a question about the ATO-DR-WE100 and is the answer not in the manual?
Questions and answers