Summary of Contents for ICON Health & Fitness NordicTrack GX 4.4 PRO
Page 1
nordictrack.com USER’S MANUAL Model No. NTEX75016.4 Serial No. Write the serial number in the space above for reference. Serial Number Decal ACTIVATE YOUR WARRANTY To register your product and activate your warranty today, go to my.nordictrack.com. CUSTOMER CARE For service at any time, go to support.nordictrack.com.
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your exercise bike before using your exercise bike. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
BEFORE YOU BEGIN Thank you for selecting the revolutionary reading this manual, please see the front cover of this NORDICTRACK GX 4.4 PRO exercise bike. Cycling manual. To help us assist you, note the product model ® is one of the most effective exercises for increasing number and serial number before contacting us.
PART IDENTIFICATION CHART Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly.
ASSEMBLY • Assembly requires two persons. • In addition to the included tool(s), assembly requires the following tools: • Place all parts in a cleared area and remove the one Phillips screwdriver packing materials. Do not dispose of the packing materials until you finish all assembly steps.
Page 8
3. Set a sturdy piece of packing material under the front of the Frame (1). Attach the Front Stabilizer (2) to the Frame (1) with two M10 x 98mm Screws (53). Then, remove the packing material. 4. With the help of a second person, raise the Upright (4) to the vertical position.
Page 9
5. Attach the Front Shield Cover (9) to the Rear Shield Cover (7) with an M4 x 16mm Flat Head Screw (93). Then, attach the Accessory Tray (8) to the Upright (4) with an M6 x 50mm Screw (89). 6. Identify the Right Armrest (16). Attach the Right Armrest (16) to the Handlebar (5) with two M4 x 22mm Screws (84).
Page 10
7. Have a second person hold the Handlebar (5) near the Upright (4). See the inset drawing. Route the Upper Wire (87) through the Pivot Post (78) and the Pivot Bracket (71) as shown. Tip: It may be easier to route the Upper Wire if you adjust the angle of the Pivot Bracket by turning the Console Knob (77).
Page 11
9. Tip: Avoid pinching the wires. Press the Front Pivot Cover (12) and the Rear Pivot Cover (15) together around the Pivot Bracket (71). Attach the Front and Rear Pivot Covers (12, 15) to the Pivot Bracket (71) with two M4 x 22mm Screws (84).
Page 12
11. Loosen the Seat Post Knob (27) and pull it out- ward. Then, remove and discard the shipping bracket (not shown) that is inside the Seat Post Sleeve (28). Next, insert the Seat Post (6) into the Seat Post Sleeve (28), and release the Seat Post Knob (27).
Page 13
13. After the exercise bike is assembled, inspect it to make sure that it is assembled correctly, that it functions properly, and that all parts are properly tightened. Note: Extra parts may be included. Place a mat under the exercise bike to protect the floor or carpet.
HOW TO USE THE EXERCISE BIKE HOW TO PLUG IN THE POWER ADAPTER HOW TO ADJUST THE LATERAL POSITION OF THE SEAT IMPORTANT: If the exercise bike has been exposed to cold temperatures, allow it to warm to room To adjust the lateral temperature before you plug in the power adapter.
HOW TO USE THE CONSOLE CONSOLE DIAGRAM When you use the manual mode of the console, you can change the resistance of the pedals with the touch of a button. While you exercise, the console will display continu- ous exercise feedback. You can also measure your heart rate using the handgrip heart rate monitor or a compatible heart rate monitor.
Page 16
HOW TO USE THE MANUAL MODE Calories per Hour (Cals/Hr)—This display will show the approximate number of calories you are 1. Turn on the console. burning per hour. Distance—This display will show the distance that Begin pedaling or press any button on the console to turn on the console.
Page 17
Scan Mode and Priority rate, hold the handgrip heart rate monitor with your Mode—The calories and watts palms resting against the contacts. Avoid moving displays will appear in an your hands or gripping the contacts tightly. alternating cycle (scan mode). To select either the calories When your pulse is detected, your heart rate will display or the watts display for continuous display...
Page 18
HOW TO USE AN ONBOARD WORKOUT level and/or target speed is programmed for the next segment, the resistance level and/or target 1. Turn on the console. speed will appear in the display to alert you. The resistance of the pedals will then change. Begin pedaling or press any button on the console to turn on the console.
Page 19
HOW TO CONNECT YOUR TABLET TO THE 4. Record and track your workout information. CONSOLE Follow the instructions in the iFit–Smart Cardio The console supports Bluetooth connections to tab- Equipment app to record and track your workout lets via the iFit–Smart Cardio Equipment app and to information.
Page 20
HOW TO USE THE SOUND SYSTEM HOW TO CHANGE CONSOLE SETTINGS To play music or audio books through the console 1. Select the settings mode. sound system while you exercise, plug a 3.5 mm male to 3.5 mm male audio cable (not included) into the To select the settings mode, press the Settings jack on the console and into a jack on your personal button.
FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
MAINTENANCE AND TROUBLESHOOTING MAINTENANCE HOW TO ADJUST THE DRIVE BELT Regular maintenance is important for optimal If the pedals slip while you are pedaling, even while the performance and to reduce wear. Inspect and properly resistance is adjusted to the highest setting, the drive belt may need to be adjusted.
Page 23
HOW TO ADJUST THE REED SWITCH Locate the Reed Switch (57). Rotate the Left Crank Arm (20) until a Magnet (55) is aligned with the Reed If the console does not display correct feedback, the Switch. Next, loosen the M5 x 16mm Flat Head Screw reed switch should be adjusted.
EXERCISE GUIDELINES Burning Fat—To burn fat effectively, you must exer- WARNING: cise at a low intensity level for a sustained period of Before beginning this time. During the first few minutes of exercise, your or any exercise program, consult your physi- body uses carbohydrate calories for energy.
PART LIST Model No. NTEX75016.4 R1019A Key No. Qty. Description Key No. Qty. Description Frame M8 x 18mm Screw Front Stabilizer Knob Nut Rear Stabilizer M8 x 76mm Bolt Upright J-bolt Handlebar #10 x 12mm Screw Seat Post M10 x 98mm Screw Rear Shield Cover Drive Belt Accessory Tray...