SAFETY PRECAUTIONS WARNINGS: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTIONS: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
The unit can playback. DVDs [8cm/12cm disc] Audio CDs [8cm/12cm disc] Region Management Information Region Management Information: This unit is designed and manufactured to respond to the Region Management Information that is encoded on DVD discs. If the Region number printed on the DVD disc does not correspond to the Region number of this unit, this unit cannot play that disc.
Please check and identify the supplied accessories. Remote control (with battery) ... x 1 AC adaptor ... x 1 AC power cord ... x 1 12V car plug adaptor ... x 1 Audio/Video cable ... x 1 EZ View cable ... x 2 Strap ...
CONTROL REFERENCE GUIDE Remote Control 1) ZOOM button Zoom into an image of a DVD. TV MODE button In stop mode, select whether to output the video signal. TV shows "AUTO" means output signal depends on DVD (either NTSC or PAL). TV shows "PAL"...
Page 8
CONTROL REFERENCE GUIDE Unit 1) Open button Open the disc door. 2) POWER ON/OFF switch 3) DC IN 12V jack 4) Disc Door Close by pushing the disc door. 5) MONITOR 1 & 2 ports (output) 6) DIGITAL OUT jack 7) DVD AV OUT jack 8) Cursor ( ) button...
CONTROL REFERENCE GUIDE Monitor DC IN 12V jack POWER ON/OFF switch POWER indicator VIDEO IN / AUDIO IN (AV1) jacks AV1 / AV2 switch AV2 (EZ VIEW CABLE) socket Connect to main unit port (Input) Headphone / Earphone jacks BRIGHTNESS control Adjust the relative lightness or darkness of the color.
INSTALLING THE STAND • Use supplied stand installing the monitors stand up on the table. 1) Hold the screws on the monitor's backward. SCREEN VIEWING ANGLE ADJUSTMENT The Monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted as top -12°~ +12°. 1.
A. Using the car power adaptor The included 12V car power adaptor is designed for use with vehicles that have a 12V, negative ground electrical system. Bottom of To AV2 socket Monitor EZ VIEW CABLES Bottom of To AV2 socket Monitor Cautions: •...
Using this Unit with Other Equipment A. Connecting Game Systems/Video Equipment • You can connect Game Systems or other Video Equipment for playback through the monitors. Right side of unit To AV IN Jack AUDIO/VIDEO CABLE (included) B. Connecting the unit to a TV •...
C. Connecting a Stereo Receiver or Amplifier Analog connection Rear of unit AUDIO/VIDEO CABLE (included) Connecting to a Surround Sound System Rear of unit Listening to another audio equipment 1. Turn on the Unit. 2. Turn on your audio equipment and follow the instructions provided with it to select the AUDIO IN or DIGITAL IN function.
You can use monitor without the main unit (DVD Player) POWER SUPPLY A. Using the AC adaptor This AC adaptor operates on AC between 100V and 240V. To AC ADAPTOR To wall outlet Cautions: • The included AC adaptor is for use with this monitor only. Do not use them with other equipment. •...
Page 15
CONNECTIONS A. Connecting the DVD Player or VCR (Yellow) (White) AUDIO/VIDEO CABLE (not included) Watching a DVD player and VCR 1. Turn on the monitor, slide the AV 1/ AV 2 switch to select "AV 1". 2. Turn on the DVD player or VCR and follow the instructions provided with it to playback. Note: If you have a mono VCR, the volume level from the speakers will be low.
MONITOR Note: When the monitor is connected to the main unit(DVD Player) with the EZ VIEW cable, DC 12V power, Audio/ Video and IR signals will all be supplied through the EZ VIEW cable to the connected monitor. So there is no need for another power source to be connected to the DC 12V jack on the right side of the monitor.
Turning the Unit On The system is in the standby condition (STANDBY indicator lights) when the AC power supply cord or Car adapter is connected. 1. Slide the POWER ON/OFF switch (on unit) to the ON position to turn ON the unit. •...
Basic playback This owner’s manual explains the basic instructions of this unit. Some DVD discs are produced in a manner that allows specific or limited operation during playback. As such, the unit may not respond to all operating commands. This is not a defect in the unit. Refer to the instructions accompanying the DVD disc.
Fast Forward/Fast Reverse 1. Press the SEARCH SEARCH button of the remote unit when a disc is playing. • The disc begins fast scan at x2 speed. • Four speeds are available. Each time SEARCH SEARCH button is pressed, the speed of fast scan changes in the following sequence: Note : You also can press and hold...
Angle selection Some DVDs contain scenes which have been shot from a number of different angles. For these discs, the same scene can be viewed from each of these different angles. 1. While you are playing a DVD with different angles recorded, press the ANGLE button to view the number of the current angle.
Basic playback DISPLAY function Using DISPLAY, you can check and change the current settings of the following : ANGLE, AUDIO and SUBTITLE. • While the disc is playing, press the DISPLAY button of the remote unit to display the screen shown below. Elapsed time: Elapsed time from the beginning of the chapter which is currently playing.
Basic playback Locating a specific title If a DVD disc contains title numbers, you can locate a specific title by directly selecting a title number. 1.Press the GOTO button. 2. Press button to highlight a specific field and press the corresponding number button(s) for the title you want.
Basic playback Locating a specific time You can move to a specific location by entering its corresponding time (hours, minutes, seconds) 1. Press the GOTO button. 2. Press button to highlight time. 3. Press the corresponding number buttons for the setting point you want. •...
Advanced CD / DVD PROGRAMMABLE MEMORY playback Programmable memory The two types of programmed playback provided by this unit are title programmed playback and chapter programmed playback. Title / Chapter programmed playback 1. Press the MEM (Memory) button while the disc is stopped. 2.
Advanced playback You can play a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat) Repeating a title You can play the same title repeatedly. 1. While the disc is playing, press the REPEAT DISC button until the “ ”...
Advanced playback Repeating a specific section You can play a specific section repeatedly. 1. While the disc is playing, press the REPEAT A-B button at the beginning of the section (( Rep A- play repeatedly. 2. Press the REPEAT A-B button again at the end of the section ) is displayed).
PLAYING A PICTURE FILE DISCS This unit can play a Picture files recorded on CD-R and CD-RW discs Playing Digital Picture files 1. Press the OPEN switch to open the disc door. 2. Hold the Picture disc by its sides and carefully fit it onto the central spindle in the disc compartment with the label side facing up.
CUSTOMIZING THE FUNCTION SETTINGS LANGUAGE setting 1. Press the SETUP button in stop mode. 2. Use button to highlight your desired language, then press the ENTER button. The screen will change to your selected language. 3. To exit the SETUP MENU and return to the normal screen, press the RETURN button.
CUSTOMIZING THE FUNCTION SETTINGS Brightness 1. Press the SETUP button in stop mode. 2. Use button to select Video, then press the ENTER button. 3. Use button to select Brightness, and then press the ENTER button. 4. Use button to shift and select the Off/On, then press the ENTER button. 5.
CUSTOMIZING THE FUNCTION SETTINGS Virtual Effect This function provides virtual surround sound effects from just two speakers. 1. Press the SETUP button in stop mode. 2. Press button to select Audio, press the ENTER button. 3. Press button to select Virtual Effect, then press the ENTER button. 4.
LANGUAGE CODE LIST Code Language Name Code Afar Abkhazian Afrikaans Ameharic Arabic Assamese Aymara Azerbaijani Bashkir Byerlorussian Bulgarian Bihari Bislama Bengali Bangla Tibetan Breton Catalan Corsican Czech Welsh Danish German Bhutani Greek English Esperanto Spanish Estonian Basque Persian Finnish Fiji Faroese French Language Name...
Cleaning Disc A defective or soiled disc inserted into the unit can cause sound to drop out during playback. Handle the disc by holding its inner and outer edges. • Do NOT touch the surface of the unlabeled side of the disc. •...
TROUBLE SHOOTING GUIDE SYMPTOM CAUSE (AND REMEDY) No power. • Check that the Car plug adapter or AC adapter and AC power cord are connected. • Turn on the unit. The remote does not • Remove any obstacles between the remote and the unit. function.
Need help?
Do you have a question about the PVS1971 and is the answer not in the manual?
Questions and answers