Advertisement
i> inte lelal-9i <5 |e
e PROGRAMABLE
REMOTE
CONTROL
UNIT
FOR VSX-5300S/KUC
TYPE (AXD1055)
LEARNING
FUNCTIONS
Introduction
This system remote control can "'learn'"' the commands of other remote
control units, regardless of manufactur, as long as the other unit is
of the infrared type.
In some cases you may still need the original remote contro! unit for
special situations. But as a rule, you will be able to use this Pioneer
remote for most system control needs, including video as well as audio
equipment.
NOTE:
When using the "LEARN"
mode it is a good idea to take the two remote
control units to another room.
This avoids problems such as sudden
high volume
output or accidental tape erasure
that may occur if
particular infrared command signals reach your components. Alterna-
tively, you may wish to unplug your component system. Simply turn-
ing off the power may not be sufficient since power on/off switching
may also be remote-controllable.
Which keys can be programmed with new commands?
There are two mode selector switches near the front end of the remote.
The LEARN mode selector lets you select the USE or LEARN function.
The LEARN
mode allows the Pioneer remote to 'LEARN' the com-
mands of other remote control units. The USE mode allows you to use
this remote control unit for operation of your system.
AUDIO mode
rene
ven, teams
Banta
SVem ny
veas
vems cov
rw
coco
Coco
co
Yaer)
vase
'
2
TORE? T6a'®
co
Tunem encowo
tases race
everem
memors 29
cOnTRoL
In the AUDIO mode the TAPE func-
tion keys can be preset with new
functions for the DAT position or
the TAPE position.
VIDEO mode
vom:
vcae
cov
C3
fa
fo
everem
memore ay
conten. ©
In the VIDEO mode the DAT/TAPE
1 switch is inoperative (43 keys can
be programmed.}.
The keys on the remote control unit change their functions according
to how the TRANSMIT
mode selector is set. You can switch the
TRANSMIT mode between the AUDIO, VIDEO, and AUX modes. How-
ever, the keys in the SURROUND AMPLIFIER section always have the
same functions.
You can assign new commands to the keys in each of the modes. In
the AUX mode, all keys are available to be programmed with new com-
mands.
In the VIDEO
and
AUDIO
modes,
all keys
except
the
SURROUND AMPLIFIER keys can be assigned new commands.
When you first start using the remote control unit, it contains initial com-
mands appropriate for Pioneer components (when set to the AUDIO
and VIDEO modes). If your audio and video equipment consists of
Pioneer components exclusively you can use the remote control unit
as is. It is also possible to restore the original Pioneer commands after
assigning other commands. (Refer to 'Returning to the Initial Settings''
for this procedure.)
* In each mode one function per key may be programmed, for a total
of up to 154 functions.
¢ When presetting keys, make sure that the remote control units of
both this and the other component are loaded with fresh batteries.
* For some special types of infrared remote contro! units, programming
may be impossible.
AUX mode
seams
—_Q teanemer
Vom cme
w
® PIONEER
AUDIO
vOWO smCom AMM Ame
REMOTE CONTRA LowrT
Cu-avoor
everem
muncore
oy
covracn =
All buttons can be preset (68 keys
can be programmed.).
In the AUX mode
the DAT/TAPE
The initial § settings will remain in
the other position (43 keys can be
Programmed.).
When teaching functions whose
names differ from those of the
keys, write in the names
or
switch is inoperative.
' codes of the functions on the
included templates and piace on
the panel.
58
Advertisement
