Advertisement
>
C= tc jal a)
@) FM/AM ANTENNA terminals
Use these antenna terminals for reception of normal FM and AM -
broadcasts.
@ STATION
PRESET/STATION
NAME switch
Determines the number of presets possible using the STATION CALL
switches.
10:
You can store a name for each station at this position, but each
STATION CALL switch can store one station (10 station total).
30:
Each STATION
CALL switch can store three stations (30
stations total). (Press once, twice, or three times to select.)
@ GND terminal
Connect the turntable ground lead to this terminal.
@ SURROUND
BALANCE
control
Use to adjust the surround effect from the surround speakers. Normally
leave in the center position. When inputting a monaural signal, adjust
so that the surround output is minimum.
© CENTER OUT jack
This is the Dolby surround center channel signal output jack.It can also
be used as a 3D system MONO output.
@ REAR SPEAKERS terminals
Connect the surround speakers to these terminals.
NOTE:
Do not allow any of the cord's conductors to protrude from the termi-
nals or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
Use surround speakers of impedance 82 — 162.
@ REMOTE CONTROL IN/OUT jacks
IN: Connect this jack to other Pioneer components (main unit or remote
control unit) when using those components to control this unit.
OUT: Connect this jack to other Pioneer components when using the
... femote control of this units to control the other components.
NOTE:
The receiver's remote sensor does not function when a plug is inserted
in the IN jack. To operate, point the remote control unit at the remote
sensor on the component to which the receiver's IN jack is connected.
To the CONTROL
IN jack of other
component.
Receiver
Pioneer component
bearing the (¥j] mark.
Remote control unit
VIDEO QUT jacks
:
Use to connect a TV set for watching program materials from a VCR
or VDP/CDV connected to this unit.
{TO MONITOR TV jacks}
Connect to monitor TV or to TV sets with video input terminals.
[TO RF MODULATOR jack]
Use to connect a normal TV set. When performing connections, the
RF MODULATOR JA-RF5 (sold separately) is required. By connecting
an RF modulator, video signals can be converted to VHF signals (U.S.
channel 3 or 4), thus allowing this unit to be used to view the selected
"source on a normal television set.
56
NOTE:
A "normal TV set'' as noted above is one for which RF connections
alone are possible.
Sound is not output from the TO RF MODULATOR jack. Use the
speakers connected to this unit to listen to the sound.
@) SPEAKERS
(FRONT) terminals
A: Connect to a first set of speakers.
B: Connect to a second set of speakers.
Speaker lead wire preparation and connection.
Cutter
2
(2)
Speaker cable
:
Push do'
@ Push up
wn.
® Insert.
NOTE:
Do not allow any of the cord's conductors to protrude from the termi-
nals or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contacts with each other.
Use speakers of impedance 42 —
162. Also set the IMPEDANCE
SELECTOR switch to match the impedance of your speakers.
AC OUTLETS
(SWITCHED TOTAL 100W MAX).
= .
Power supplied through these outlets is turned on and off by the
receiver's POWER switch. Total electrical power consumption of con-
nected equippment should not exceed 100W.
(UNSWITCHED 200 W (U.S. and Canadian model), 100 W (Multi-
voltage model) MAX)
Power flows continually to this outlet, regardless of whether the receiver
is switched ON or OFF. Electrical power consumption of the connect -
ed equipment should not exceed 200 W (U.S. and Canadian model),
100 W (Multi-voltage model).
The equipment should be disconnected by removing the power plug
from the wall socket when not in regular use, e.g. when on vacation.
NOTE:
Do not connect appliances with high power consumption such as heat-
ers, irons, or television sets to the AC OUTLETS in order to avoid over-
heating or fire risk.
This can cause the receiver to malfunction.
@ IMPEDANCE
SELECTOR
switch
Set this switch to match the impedance of your speakers.
position
position
ome
A ORB
AORB
40 TO LESS THAN 82
82 OR MORE
AANDB
82 OR MORE
« When using a pair of speakers:
Advertisement
