Advertisement
Troubleshooting
If the wireless signal indicator shows no bars:
• Relocate the display unit and/or the outdoor sensor.
The units must be within 165 ft (50 m) of each other.
No outdoor Hnsor
• Make sure both units are placed at least 3 feet (.9 m)
away from electronics that may interfere with the
reception
wireless communication (such as TVs, microwaves,
THII
no bars
computer1, etc).
• Use standard alkaline batteries (or lithium batteries in
sensor when temperature is below -4°F/-20°C). Do not
use heavy duty or rechargeable batteries. NOTE: It
may
take
up to 20 minutes for display unit and sensor
to synchronize after batteries are replaced.
Flashing of the outdoor temperature is generally an
indication of wireless interference.
Outdoor
1. Bring both the sensor and display unit indoors and
temperature
remove at least one battery from each.
11 flashing or
2. Reinstall the battery in the outdoor sensor.
showing dashH
3. Reinstall the battery in the display unit.
4. Let the uf its sit within a couple feet of each other
for abou 20 minutes to gain a strong connection.
Inaccurate
• Make sure both the display unit and sensor are
temperature
placed out of direct sunlight and away from any heat
sources or vents (see page_6).
Display screen
• Check that the batteries are installed correctly.
not working
Batteries may need to be replaced.
I
I
If your AcuRite product does not operate properly after trying
the troubleshooting steps, visit www.AcuRite.com or email
support@chaney-lnst.com for assistance.
I
1
8
Care
&
Maintenance
Display Unit Care
/
I
Cleon with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt and moisture. Cleon ventilation ports regularly with a
gentle puff of air.
Outdoor Sensor Care
[
Clean with a soft damp cloth. Do not uselcaustic cleaners or abrasives.
Specifications
TEMPERATURE RANGE
Outdoor: -40°F to 158°F;
-40°C
to 70°C
Indoor: 32°F to 122°F; 0°C to 50°C
WIRELESS RANGE
165 ft / 50 m depending on home construction materials
WIRELESS FREQUENCY
433
MHz
POWER
Display: 2 x AAA alkaline batteries
Sensor: 2 x AA alkaline or lithium batteries
DATA REPORTING
30 second upd~tes
FCC Information
This device complies with part 15 of FCC rule,. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications lo this unit not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant lo Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, ii not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. II this equipment does cause harmful interference lo radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged lo try to correct the interference by one or more of the following measures:
• Reorient or reloccte the receiving antenna.
• lncroaat the 1eporation belwHn the equipment and the receiver.\
• Connell tht equipment Into on outlet on o circuit different from that to which the receiver is connected.
• Consuh the daoler or on experienced radio/TV technician for he. I p.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
Such modifications could void the user authority to operate the eq~pmenl.
This device complies with Industry Canada licence-exempt RSS stanpard(s).
Operation is subject to the following two conditions:
(1
J
This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
9
Advertisement
