Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Wisenet ONV-9081R
Summary of Contents for Wisenet ONV-9081R
- Page 1 NETWORK CAMERA User Manual ONV-9081R ONO-9081R...
- Page 2 Network Camera User Manual Copyright ©2021 Co., Ltd. All rights reserved. Hanwha Techwin Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved.
- Page 3 15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated EXPLANATION OF GRAPHICAL SYMBOLS from 12 Vdc 1.8 A, or PoE, 0.46 A. (ONV-9081R) 16. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated The lightning flash with arrowhead symbol, within an equilateral triangle, is from 12 Vdc 1.9 A, or PoE, 0.47 A.
- Page 4 For below models only. The ITE is to be connected only to PoE networks without routing to the outside plant. ONV-9081R/ONO-9081R The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3at shall be a UL Listed device with the output evaluated as a Limited Power Source Risk Group 1 as defined in UL60950-1 or PS2 as defined in UL62368-1.
-
Page 5: Table Of Contents
CONTENTS OVERVIEW NETWORK CONNECTION AND Important Safety Instructions Connecting the Camera Directly to Local Recommended PC Specifications Area Networking SETUP Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs Optional Accessories for Installation OUTDOOR VANDAL DOME CAMERA What’s Included WEB VIEWER Connecting to the Camera At a Glance Password setting... -
Page 6: Recommended Pc Specifications
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS ~ CPU : Intel(R) Core(TM) i7 3.4 GHz or higher ~ Recommended capacity : 200GB or higher is recommended. ~ RAM : 8G or higher ~ For this camera, you are recommended to use a NAS with the following manufacturer’s specs. ~ Recommended browser: Chrome Recommended products : QNAP NAS, Synology NAS ~ Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based) - Page 7 Outdoor Vandal Dome Camera Outdoor Bullet Camera ONV-9081R ONO-9081R English _7...
-
Page 8: Optional Accessories For Installation
You can purchase appropriate optional accessories available. Model name Hanging Mount Pole Mount SBP-300LMW (Parapet Mount) SBP-300CMW (Ceiling Mount) SBP-300WMW (Wall Mount) SBP-300WMW1 (Wall Mount) ONV-9081R SBP-187HMW SBP-300NBW (Instalation Box) SBP-300NBW (Wall Mount Base) SBP-300PMW (Pole Mount) SBP-300KMW (Corner Mount) ONO-9081R SBP-302PM... -
Page 9: Outdoor Vandal Dome Camera
WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Mount-plate Camera body Dome-cover ONV-9081R Pipe-cover IR LED Reset button Illumination Sensor Zoom/Focus Control Button Network Port Micro USB port Power port... -
Page 10: Installation
outdoor vandal dome camera INSTALLATION 2. Take off the lens cover protecting the camera lens. This camera is waterproof and in compliance with the IP67 / IP6K9K spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. Precautions before installation Ensure you read out the following instructions before installing the camera: ~ Select an installation site that can hold at least 5 times the camera’s weight. - Page 11 Installation (mount plate) [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. [Directly installing on wall/ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. 2-2. Separate the pipe cover of the mount plate by pressing its sides. 1-2.
- Page 12 outdoor vandal dome camera 2-3. Place the pipe on the mount plate. 1-4. Mount the cable bushing to the camera body. 2-4. Fix the mount plate using appropriate screws. 2-5. Pull out necessary cables among network/power cables through the pipe. [Installing the network cable] (IP66) Installation 2-1.
- Page 13 2-3. Mount the cable bushing to the camera body. 4. Connect the network/power cables to the port on the camera body. 5. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the camera” section. (page 21) 3.
- Page 14 outdoor vandal dome camera Outdoor installation Be careful not to alter the monitoring direction of your camera. When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1.
-
Page 15: Outdoor Bullet Camera
outdoor bullet camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Sunshield fixing screw Pipe-cover Washer Mount plate Sunshield Bottom cover ONO-9081R Camera body Micro USB port Test monitor out port Network port Zoom/Focus Control Button Power Port... -
Page 16: Installation
outdoor bullet camera INSTALLATION 1-2. Fix the Mount plate using appropriate screws. 1-3. Pull out necessary cables among network/power cables through the hole in the Mount plate. This camera is waterproof and in compliance with the IP67 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. - Page 17 2-2. Separate the pipe cover of the Mount plate by pressing its sides. Installation (Bottom cover) Use a cable bushing compliant with the network cable to be connected. Camera main: use a cable with the diameter of Ø5 to 6.5 Components: use a cable with the diameter of Ø5 to 8.5 [Installing network/power cables] 1-1.
- Page 18 outdoor bullet camera [Installing the network cable] 3. Join the Mount plate with the Bottom cover. 2-1. Pull off the extruded part of the 1-hole cable bushing provided. 2-2. Use the cap installer to pass through the RJ45 cable. Cap Installer 2-3.
- Page 19 Installing the camera module 3. Attach the camera body to the Bottom cover. 1. Hang the safety wire on the hook inside the bottom cover. Make sure to firmly tighten the fastening screws so that there is no water damage issue. e.g.) 4.
- Page 20 outdoor bullet camera 5. Assemble the sunshield to the camera body using sunshield fixing screw. Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be Sunshield fixing screw purchased in stores) so that water does not leak from the gap of the cable connected to the outside. Washer 1.
-
Page 21: Installation & Connection
installation & connection ADJUSTING THE MONITORING DIRECTION FOR THE CAMERA Adjust the direction of IR LEDs not to hinder their view by an instrument. Tilt Lens rotation ` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling. At this time, rotating the main body of the camera in the left and right direction is called PAN, and adjusting the angle of the camera is called TILT. -
Page 22: Connecting With Other Device
Camera Setup 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB port. Smartphone Setup 1. Install the Wisenet Installation application. 2. Select the camera SSID after turning on the WiFi. 3. Run the Wisenet Installation application. 4. When you log in to the camera, the video will be connected. - Page 23 Connect the set and the adapter power line first, and then connect the power cable to the outlet on the wall. Power Cable Specification for Each Model Model Input power Wire Type (AWG) Cable Length (Max.) ONV-9081R DC 12V ONO-9081R Be careful not to reverse the polarity when you connect the power cable. Network Cable Specification Item...
-
Page 24: Connecting The Camera Directly To Local Area Networking
network connection and setup network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN 1. Launch an Internet browser on the local PC. 2. -
Page 25: Connecting To The Camera
web viewer CONNECTING TO THE CAMERA PASSWORD SETTING When you access the product for the first time, you must register the Normally, you would login password. By factory default, the IP address will be assigned from the DHCP server automatically. If there is no DHCP server available, the IP address will be set to 192.168.1.100. -
Page 26: Camera Web Viewer Setup
web viewer CAMERA WEB VIEWER SETUP 1. Click the [Setup ( )] icon. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and system over the network. 4. Click <Help ( )>... -
Page 27: Troubleshooting
appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM SOLUTION When an Windows 10 user accesses Cannot record in the NAS. ~ Confirm that the information registered in the NAS is correct. ~ This is what happens when microphone driver has been set to Realtek driver. the web viewer through Chrome Install the High Definition Audio device (Windows Default Driver) or the third party driver as or Firefox, the sound volume of... - Page 28 Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the ONV-9081R and is the answer not in the manual?
Questions and answers