Wisenet XNP-9300RW User Manual
Hide thumbs Also See for XNP-9300RW:

Advertisement

NETWORK CAMERA
User Manual
XNP-9300RW
XNP-8300RW
XNP-6400RW

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XNP-9300RW and is the answer not in the manual?

Questions and answers

Summary of Contents for Wisenet XNP-9300RW

  • Page 1 NETWORK CAMERA User Manual XNP-9300RW XNP-8300RW XNP-6400RW...
  • Page 2 Network Camera User Manual Copyright ©2020 Co., Ltd. All rights reserved. Hanwha Techwin Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved.
  • Page 3 overview WARNING IMPORTANT SAFETY INSTRUCTIONS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT 1. Read these instructions. TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE 2. Keep these instructions. VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT. 3.
  • Page 4 For below models only. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802.3bt shall be a UL Listed device with the output evaluated as a Limited Power Source XNP-9300RW as defined in UL60950-1. XNP-8300RW Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102.
  • Page 5: Table Of Contents

    CONTENTS OVERVIEW WEB VIEWER Important Safety Instructions Connecting to the Camera Recommended PC Specifications Password setting Recommended Micro SD/SDHC/SDXC Login Memory Card Specifications Camera Web Viewer Setup NAS recommended specs What’s Included Optional Accessories for Installation At a Glance APPENDIX Troubleshooting INSTALLATION &...
  • Page 6: Overview

    overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS • CPU : Intel(R) Core(TM) i7 3.4 GHz or higher • Recommended capacity : 200GB or higher is recommended. • RAM : 8G or higher • For this camera, you are recommended to use a NAS with the following manufacturer’s specs. Recommended products : QNAP NAS, Synology NAS •...
  • Page 7: What's Included

    WHAT’S INCLUDED OPTIONAL ACCESSORIES FOR INSTALLATION Please check if your camera and accessories are all included in the product package. You can purchase appropriate optional accessories available. (As for each sales country, accessories are not the same.) Appearance Item Name Quantity Description Main Body...
  • Page 8 overview AT A GLANCE Appearance Inside Item Description Item Description Main cover IR LED Protects the internal PTZ mechanism from the direct sunlight, rain or external impact. These infrared LED’s are controlled by the illumination sensor. Used for wiping off raindrops or snow dripping on the window. Lens Lens for the camera.
  • Page 9 Mounting surface Item Description Cable bushing A waterproof rubber cap, which allows a network cable to go through it. Hang this hook on the safety wire of the mount when installing this product to prevent it Safety wire hook from falling. A port that connects to the HPoE injector and network cable for power and network HPoE port connection.
  • Page 10: Installation & Connection

    installation & connection INSTALLATION 2. Pull up the Micro SD card cover and push the Micro SD card to the arrow direction as shown in the figure. This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
  • Page 11 Removing a Micro SD card Getting ready for network cable installation Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD 1. Remove the cable bushing. card from the slot. Before removing the Micro SD card, in <Storage>, set the device to <Off>...
  • Page 12 installation & connection 4. For waterproof protection, pull down the cable below the cable bushing as shown in the figure below. 2. Connect the network cable to the HPoE port. 9~10 cm Installing using wall & pole mount 3. Plug the cable bushing of the network cable in the hole. Power on the HPoE injector only after installation is complete.
  • Page 13 4. Install the bushing clip. 6. Tightly fasten the 3 mounting screws on the inside of the Wall & Pole Mount. Let the arrow mark on the clip point in the direction of the safety wire hook, and click each side into place one at a time.
  • Page 14 installation & connection Installing with hanging mount 3. Connect the network cable to the HPoE port. If you use hanging mount, you can install the camera onto any mount other than the official product mount. 1. Install the hanging mount by turning it counterclockwise into the installed mount. 4.
  • Page 15 5. Install the bushing clip. 7. Tightly fasten the 3 mounting screws on the top side of the Hanging Mount. Let the arrow mark on the clip point in the direction of the safety wire hook, and click each side into place one at a time.
  • Page 16 installation & connection Replacing the rubber of wiper blade 3. Remove the rubber part by pulling it back. If the rubber part of your wiper blade is worn and not cleaning the window properly, you can replace the rubber part. 1.
  • Page 17 POWERING AND NETWORKING SFP port Specification Support SFP Voltage 3.3 V Typical Connect the HPoE injector with the HPoE port of the camera. Support SFP Current 300 mA Max. Support SFP Cage Standard mini-SFP Cage(for 6.5 mm pitch SFP) Support SFP Port Type LC Type HPoE injector Required SFP Speed...
  • Page 18: Network Connection And Setup

    network connection and setup CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE You can set up the network settings according to your network configurations. MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET 1.
  • Page 19: Using Device Manager

    USING DEVICE MANAGER If using a Broadband Router • IP Address : Enter an address falling in the IP range provided by the Broadband Router. Device manager program can be downloaded from <Technical Guides>-<Online Tool> menu at Hanwha Techwin website ex) 192.168.1.2~254, 192.168.0.2~254, (http://www.hanwha-security.com).
  • Page 20: Manually Registering Camera

    • Example of the Dynamic IP environment configure the IP. XNP-9300RW - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2. Click < + > at the main page of device manager.
  • Page 21: Port Range Forward (Port Mapping) Setup

    Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function. For more information, refer to the user manual of the applicable router. After connecting the network camera, select the checkbox from the menu <Quick connect> in <Wisenet DDNS> in “Settings -> Network -> DDNS”.
  • Page 22: Connecting To The Camera From A Shared

    2. From the remote PC, launch the Internet browser and type the DDNS URL address of the camera, or the IP address of the Broadband Router in the address bar. ex) http://ddns.hanwha-security.com/ID To use Wisenet DDNS, sign up at the Wisenet DDNS homepage (http://ddns.hanwha-security.com) and register the product at [My DDNS]>[Register Product]. 22_ network connection and setup...
  • Page 23: Connecting To The Camera

    To register your device to the <DDNS> server, visit http://ddns.hanwha-security.com and register your device first, and then set the Web Viewer’s <Network> - <DDNS> to <Wisenet DDNS>, as well as providing 2. Type the IP address and HTTP port number of the camera in the address bar.
  • Page 24: Password Setting

    web viewer PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the Setup ( 1. Click the [ ] icon. login password. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and For a new password with 8 to 9 digits, you must use at least 3 of system over the network.
  • Page 25: Troubleshooting

    appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM SOLUTION y On the authentication popup window prompted when initially accessing https, click "View y Verify the settings in the following sequence: <Motion detection> of <Analytics> is Authentication Certificate" and select the "Always trust when connecting to the designated set to <Enable>, but no notification A.
  • Page 26 Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This manual is also suitable for:

Xnp-8300rwXnp-6400rw

Table of Contents