Husqvarna 325iR Operator's Manual page 14

• Always use approved protective googles that comply
with ANSI Z87.1 standard in the USA or EN 166 in
EU countries.Use visor for face protection. Visor is
not enough to protect the eyes.
(Fig. 19)
• Use gloves when it is necessary, for example when
you attach, examine or clean the cutting equipment.
• Use protective boots with steel toe-cap and non-slip
soles.
• Use clothing made of a strong fabric. Always use
heavy, long pants and long sleeves. Do not use
loose clothing that can catch on twigs and branches.
Do not use jewelry, short pants or sandals. Do not
go with bare feet. Put your hair up safely above
shoulder level.
(Fig. 20)
• Keep first aid equipment near.
(Fig. 21)
Safety devices on the product
WARNING:
instructions that follow before you use the
product.
In this section the product's safety features, its purpose
and how checks and maintenance should be carried
out to ensure that it operates correctly. See instructions
Product overview on page 8 to find
under the heading
where these parts are located on your product.
The life span of the product can be reduced and the risk
of accidents can increase if product maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest servicing dealer.
WARNING:
damaged safety components. The product's
safety equipment must be inspected and
maintained as described in this section.
If your product fails any of these checks,
contact your service agent to get it repaired.
CAUTION:
on the machine requires special training.
This is especially true of the machine's
safety equipment. If your machine fails
any of the checks described below you
must contact your service agent. When
you buy any of our products we guarantee
the availability of professional repairs and
service. If the retailer who sells your
machine is not a servicing dealer, ask him
for the address of your nearest service
agent.
14
Read the warning
Never use a product with
All servicing and repair work
To do a check of the user interface
1. Press and hold the start/stop button (A).
a) The product is on when the display (B) comes
on. (Fig. 22)
b) The product is off when the display goes off.
2. If the warning indicator on the display is on or
Troubleshooting on page 20 .
flashes, refer to
To do a check of the power trigger lockout
The power trigger lockout prevents accidental operation.
When you push the power trigger lockout forward (A)
and then press the power trigger lockout against the
handle (B), the power trigger (C) is released. When you
release the handle, the power trigger and the power
trigger lockout move back to their initial positions. This
movement is operated by independent springs.
(Fig. 23)
1. Make sure that the power trigger is locked when the
lock is in its initial position. (Fig. 24)
2. Press the power trigger and make sure that it goes
back to its initial position when you release it. (Fig.
25)
3. Make sure that the power trigger and the lock moves
freely and that the return spring operates correctly.
(Fig. 26)
4. Start the product, refer to
page 18 .
5. Apply full speed.
6. Release the power trigger and make sure that the
cutting attachment stops fully.
Quick-release function of the harness
WARNING:
with a quick-release function that does
not operate correctly. Make sure that the
harness quick-release function operates
correctly when you adjust the product.
• The harness quick-release function is at the front of
the product.
(Fig. 27)
• The harness straps must always stay at the correct
position.
• In an emergency, the harness quick-release function
helps you to safely release from the product.
To do a check of the cutting attachment guard
WARNING:
attachment without an approved and
correctly attached cutting attachment guard.
Always use the recommended cutting
attachment guard for the cutting attachment
that you use, see
If an incorrect or faulty cutting attachment
To start the product on
Do not use the harness
Do not use a cutting
Accessories on page 23 .
1859 - 005 - 21.09.2023