Table of Contents
Advertisement
Basic setting
Wi-Fi
Remote control status Monitoring
15.3 Operating the appliance with the
Home Connect app
You can use the Home Connect app to set and start
the appliance remotely.
WARNING ‒ Risk of fire!
Combustible objects that are left in the cooking com-
partment may catch fire.
Never store combustible objects in the cooking
▶
compartment.
If smoke is emitted, the appliance must be switched
▶
off or the plug must be pulled out and the door
must be held closed in order to stifle any flames.
Requirements
¡ The appliance is switched on.
¡ The appliance is connected to the home network
and to the Home Connect app.
¡ In order to be able to set the appliance via the app,
the manual or permanent remote start must be se-
lected in the "Remote control status" basic setting.
To activate remote start, press .
1.
Configure a setting in the Home Connect app and
2.
send it to the appliance.
Notes
¡ When you start the oven using the controls on
the appliance itself, the remote start function is
activated automatically. You can use the
Home Connect app to adjust the settings or start
a new programme.
¡ You can open the appliance door within 15
minutes of having activated remote start. Remote
start will not be deactivated by this. Once 15
minutes have elapsed, opening the appliance
door will deactivate manual remote start.
15.4 Software update
Your appliance's software can be updated using the
software update function, e.g. for the purposes of op-
timisation, troubleshooting or security updates.
To do this, you must be a registered Home Con-
nect user, have installed the app on your mobile device
and be connected to the Home Connect server.
Possible settings
On
Off
Manual remote start
Permanent remote start
Explanation
You can use the Wi-Fi to switch off the network connection for
your appliance. When you have connected successfully once,
you can deactivate the Wi-Fi and not lose your detailed data.
As soon as you activate Wi-Fi again, the appliance connects
automatically.
Note: In networked standby mode, the appliance requires a
maximum of 2 W.
During monitoring, you can only view the operating status of
the appliance in the app.
For manual remote start, you must activate the remote start
each time before you can start the appliance via the app. You
can open the appliance door within 15 minutes of having activ-
ated remote start. Remote start will not be deactivated by this.
Once 15 minutes have elapsed, opening the appliance door
will deactivate manual remote start.
For permanent remote start, you can start and operate the ap-
pliance remotely at any time. If you often operate the appliance
remotely, it is helpful to set the remote start to "Permanent".
As soon as a software update is available, you will be
informed via the Home Connect app and will be able to
start the software update via the app. Once the update
has been successfully downloaded, you can start in-
stalling it via the Home Connect app if you are in your
home network (Wi-Fi). The Home Connect app informs
you once installation is successful.
Notes
¡ The software update consists of two steps.
– The first step is the download.
– The second step is the installation on your appli-
ance.
¡ You can continue to use your appliance as normal
while updates are downloading. Depending on your
personal settings in the app, software updates can
also be set to download automatically.
¡ Installation takes a few minutes. You cannot use
your appliance during installation.
¡ We recommend that you install security updates as
soon as possible.
15.5 Remote diagnostics
Customer Service can use Remote Diagnostics to ac-
cess your appliance if you contact them, have your ap-
pliance connected to the Home Connect server and if
Remote Diagnostics is available in the country in which
you are using the appliance.
Tip: For further information and details about the avail-
ability of Remote Diagnostics in your country, please
visit the service/support section of your local website:
www.home-connect.com.
15.6 Data protection
Please see the information on data protection.
The first time your appliance is registered on a home
network connected to the Internet, your appliance will
transmit the following types of data to the
Home Connect server (initial registration):
¡ Unique appliance identification (consisting of appli-
ance codes as well as the MAC address of the Wi-Fi
communication module installed).
¡ Security certificate of the Wi-Fi communication mod-
ule (to ensure a secure data connection).
Home Connect en
17
Advertisement
Table of Contents
