Package Contents; Markings On Tool; Description (Fig. A); Intended Use - DeWalt DCG440NLR Original Instructions Manual

English
p
See Technical Data for charging time.
q
Do not probe with conductive objects.
r
Do not charge damaged battery packs.
s
Do not expose to water.
t
Have defective cords replaced immediately
u
Charge only between 4 ˚C and 40 ˚C.
v
Only for indoor use.
x
Discard the battery pack with due care for
the environment.
y
Charge battery packs only with designated D
chargers. Charging battery packs other than the
designated D WALT batteries with a D
e
charger may make them burst or lead to other
dangerous situations.
z
Do not incinerate the battery pack.
B
USE (without transport cap). Example: Wh rating
indicates 108 Wh (1 battery with 108 Wh).
A
TRANSPORT (with built‑in transport cap). Example: Wh
rating indicates 3 x 36 Wh (3 batteries of 36 Wh).
Battery Type
The following tools operate on a 54 volt battery pack: DCG440
These battery packs may be used: , DCB546, DCB547, DCB548,
DCB549. Refer to Technical Data for more information.

Package Contents

The package contains:
1 Angle grinder
1 180 mm Guard (Type B)
1 180 mm Guard (Type A)
1 Side handle
1 Side handle extension
1 Hex wrench
2 Li‑Ion battery pack (T2, X2 models)
1 Li‑Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1, Y1 models)
2 Li‑Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2, Y2 models)
3 Li‑Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3, Y3 models)
1 Instruction manual
nOTE: Battery packs, chargers and kitboxes are not included
with N models. Battery packs and chargers are not included with
NT models. B models include Bluetooth® battery packs.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
12
such marks by D
trade names are those of their respective owners.
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.

Markings on Tool

The following pictograms are shown on the tool:
a
g
f
n
Date Code Position (Fig. B)
The date code
is printed into the housing.
WALT
e
Example:
WALT
e
Description (Fig. A)

Trigger switch
1
Lock‑off lever
2
Spindle lock button
3
Spindle
4
Auxiliary handle
5
Grinding wheel
6
Unthreaded backing flange (fixed to spindle)
7
Locking flange
8
Type B Guard 180 mm (Do not use for cut‑off operations)
9
Guard release lever
10
Battery pack
11
Battery release button
12
Main Handle
13
Type A Guard 180 mm
14
Side handle extension
15

Intended Use

The DCG440 cordless angle grinder has been designed
for professional cutting, grinding, sanding and wire
brush applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
This cordless angle grinder is a professional power tool.
DO nOT let children come into contact with the tool. Supervision
is required when inexperienced operators use this tool.
WALT is under license. Other trademarks and
e
Read instruction manual before use.
Wear ear protection.
Wear eye protection
Visible radiation. Do not stare into light.
, which also includes the year of manufacture,
30
2020 XX XX
Year and Week of Manufacture
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.