Table of Contents
Advertisement
Quick Links
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
Fig. A
3
10
4
Trigger switch
1
Lock-off lever
2
Spindle lock button
3
Spindle
4
Side handle
5
Grinding wheel (Fig. G)
6
Unthreaded backing flange
7
Locking flange
8
Type 27 Guard (x2) 6"and 4.5"
9
Guard release lever
10
Battery pack
11
Battery release button
12
9
5
7
8
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING: To reduce the risk of injury, read the
instruction manual.
if you have any questions or comments about this or
any D
WALT tool, call us toll free at:
e
1-800-4-D
WALT (1-800-433-9258).
e
English
12
11
1
2
1
Advertisement
Table of Contents
Related Manuals for DeWalt DCG414T2
Summary of Contents for DeWalt DCG414T2
- Page 1 English Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
-
Page 2: General Power Tool Safety Warnings
English GENERAL POWER TOOL SAFETY WARNINGS b ) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust WARNING! Read all safety warnings and all mask, non-skid safety shoes, hard hat, or hearing instructions. Failure to follow the warnings and protection used for appropriate conditions will reduce instructions may result in electric shock, fire and/or personal injuries. -
Page 3: Safety Warnings Common For Grinding
English into account the working conditions and the e ) The outside diameter and the thickness of your work to be performed. Use of the power tool for accessory must be within the capacity rating of operations different from those intended could result your power tool. -
Page 4: Kickback And Related Warnings
English n ) Regularly clean the power tool’s air vents. The toward or away from the operator, depending on direction motor’s fan will draw the dust inside the housing and of the wheel’s movement at the point of pinching. Abrasive excessive accumulation of powdered metal may cause wheels may also break under these conditions. -
Page 5: Additional Safety Information
English f ) Do not use worn down wheels from larger power to the brush. The wire bristles can easily penetrate tools. Wheel intended for larger power tool is not light clothing and/or skin. suitable for the higher speed of a smaller tool and b ) If the use of a guard is recommended for wire may burst. -
Page 6: Batteries And Chargers
English battery packs will stand upright on the battery pack • Charge the battery packs only in designated but may be easily knocked over. WALT chargers. • Air vents often cover moving parts and should be • DO NOT splash or immerse in water or other liquids. avoided. - Page 7 1-800-4-D WALT (1-800-433-9258) or quantity of three batteries with the lower watt hour rating visit our website www.dewalt.com. can exempt the pack from certain shipping regulations that The RBRC® Seal are imposed upon the higher Watt hour batteries.
- Page 8 English Any other uses may result in risk of fire, electric shock electric shock. Removing the battery pack will not reduce or electrocution. this risk. • Do not expose the charger to rain or snow. • NEVER attempt to connect 2 chargers together. • Pull by the plug rather than the cord when •...
-
Page 9: Charger Operation
English Charger Operation Wall Mounting Refer to the indicators below for the charge status of the DCB107, DCB112, DCB113, DCB115, DCB118, DCB132 battery pack. These chargers are designed to be wall mountable or to sit upright on a table or work surface. If wall mounting, DCB101 locate the charger within reach of an electrical outlet, Charging... -
Page 10: Intended Use
English ASSEMBLY AND ADJUSTMENTS is no battery pack in the cavity. Unplug the charger before attempting to clean. WARNING: To reduce the risk of serious personal 6. Do not freeze or immerse the charger in water or any injury, turn unit off and remove the battery pack other liquid. - Page 11 English for the manufacturer's label to see if they can be used for 3. Replace the lever, positioning the chosen end under the surface grinding or only edge grinding/cutting. A Type 1/41 spring 13 . Ensure the lever is in proper contact with guard must be used for any wheel where surface grinding the spring.
- Page 12 English Mounting Non-Hubbed Wheels (Fig. H) WARNING: Proper guard must be reinstalled for grinding wheel, cutting wheel, sanding flap disc, WARNING: Failure to properly seat the flange/ clamp wire brush or wire wheel applications after sanding nut/ wheel could result in serious injury (or damage to applications are complete.
-
Page 13: Operation
English Mounting Wire Cup Brushes and WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a Wire Wheels sudden reaction. CAUTION: To reduce the risk of personal injury, Proper hand position requires one hand on the main handle wear work gloves when handling wire brushes and one hand on the side handle. - Page 14 English recommend the following precautions when sanding Fig. N any paint: Personal safety 1. No children or pregnant women should enter the work area where the paint sanding or wire brushing is being done until all clean up is completed. 2.
-
Page 15: Maintenance
Federal Consumer into a liquid. Safety Act. Accessories Register online at www.dewalt.com/register. The capacity of this tool is 6" (152.4 mm) diameter x Three Year Limited Warranty 1/4" (6.35 mm) thick grinding or cutting wheels. It is important to choose the correct guards, backing pads and WALT will repair, without charge, any defects due to flanges to use with grinder accessories. - Page 16 WALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase. 2 YEARs FREE sERViCE On DEWAlT BATTERY PACKs DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120, DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361...